PROAIM 14ft. Jib Arm with Jib Stand Manual de usuario
14ft. Jib Arm with Jib Stand
(P-14-JS)
I n s t r u c t i o n M a n u a l
All rights reserved
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permied by
the applicable copyright statutes or in wring by the publisher.
PROAIM 14FT JIB ARM WITH STAND 2
IT IS IMPORTANT THAT YOU READ AND UNDERSTAND THIS GUIDE BEFORE ATTEMPTING TO
ASSEMBLE OR USE YOUR NEW PROAIM 14’ JIB ARM.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS AVAILABLE ‘ON
LINE' BY CONTACTING YOUR SALES REPRESENTATIVE.
INTRODUCTION
PROAIM welcomes you to the new and modernized era with its huge & sturdy 14 Jib Arm with
Jib Stand, a perfect lming soluon to increase your producon value. The Robust camera crane
produces breathtaking footage through its huge set of features at a small price. Lcd mounng
opon enables beer viewing possibilies for operator.
WHAT’S IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below. The padded shipping /storage container has been especially designed
to protect your purchase while in transit and is a good place to keep your PROAIM 14’ Jib Arm
when not in use.
PACKED IN AN EASY CARRY, PROTECTIVE TOTE BAG.
CONTENTS OF SHIPPING BOX:
Four 3.5 Secons
Central Post
Weight Shank
Weight Closers
Jib Stand
LCD Mounng Arm
Tool Pouch
This Manual
1st secon
2nd secon
3rd secon
4th secon
Weight closer Weight shank
Central post
Jib stand
Tool Pouch
LCD mounng arm
PROAIM 14FT JIB ARM WITH STAND 3
Using the following pictures and text as a guide for set up, please follow the instrucons in
order of appearance.
For stability and mounng of your 14’ Jib Arm on the stand take out the stand from the case
and proceed as follows:
Loosen the lower knob 1 located at the top of the spreader legs
Slide the legs down the center post to the widest possible posion and ghten the knob 1
to secure.
NOTE: A wider spread ensures more stability.
Draw the center post up to the desired jib height and lock into place using the provided
locking pin.
ASSEMBLING THE JIB ARM
Slide the Central Post of the Jib onto the Stand Mount and ghten the knob 2 to secure it.
JIB STAND SET UP
Knob 1
Knob 2
PROAIM 14FT JIB ARM WITH STAND 4
CONNECT THE 3RD JIB SECTION TO THE CENTER POST
Open the shank from the central post.
Leave the black washers at one side.
Then insert the end of this secon
inside the Center Post and align the
holes of the secon with the central
post to screw in the shank.
Similarly, insert the black washers
onto the other side and push the
shank towards the other side in order
to ghten the shank with the dome
nut.
Using a wrench, ghten the dome
nut from both sides to secure the
two secons.
PROAIM 14FT JIB ARM WITH STAND 5
CONNECTING ARM SECTIONS 3 WITH 2, 2 WITH 1 & 4 WITH 3
The 3rd secon has connecng bars aached to both the ends. Slide the bars of secon 3
into the slots of secon 2 & ghten both the secons together using the provided allen
Key. Similarly slide in secon 1 into secon 2 and nally secon 4 into secon 3.
Tighten the allen bolts as before to secure the secons. Your jib arm is now completely
connected
Tighten the wire puller and its
central pool adapter. Tighten the
bolts to secure them
ADJUSTING THE WIRE TENSIONER
To add strength and stability to your
Jib and allow for maximum weight
carrying, the fore and a wire ends
once posioned need to have the
slack taken out by use of the wire
adjuster shown above. Once
connected in line with the wire,
simply rotate the mid secon han-
dle to ghten the wire adding the
required amount of strength to the
system.
Screw-In System
Wire Adjustment
PROAIM 14FT JIB ARM WITH STAND 6
ADDING THE COUNTER WEIGHTS
Securing the counter weights to the Jib
is accomplished by the use of the
stainless steel shank. It has two lock
os, one for each side of the Arm to
prevent the weights from shiing
during use or accidentally falling o the
jib.
Standard exercise weights (not
supplied) with a 1’ hole are easily
mountable and are used to equal the
weight placed on the camera side of
the Jib.
Once you discover correct balance,
consider marking the weights for that
parcular camera facilitang an easier
set up the next me.
Weights shown in
The image are for
Demonstraon.
CAMERA MOUNTING PLATE
To accommodate various manufactur-
ers and dierent sized cameras,
mulple slots are provided for
aachment.
You will need to ne tune your
counterweights to accommodate
camera, head and other accessories
being used on the Jib Arm.
MOUNTING THE PAN-TILT HEAD
If you are using the remote capability of a
Pan/Tilt Head, it can be easily mounted to
the jib via the 4 slots located at the
corners of the plate using 4 screws.
This assembly is usually accomplished
from the underside (boom) of the jib
camera plate.
PROAIM 14FT JIB ARM WITH STAND 7
PIN FEATURE FOR TILTING SHOTS
Removing the locking pin on the Center
Post allows the operator to frame lng
shots by the use of control handle.
MOUNTING A MONITOR
Provisions for LCD monitor mounng to
the Jib Arm are built in. The monitor is
not provided.
PROAIM 14FT. JIB ARM WITH JIB STAND
ALL DRESSED UP AND GOOD TO GO
(SHOWN WITH OPTIONAL ACCESSORIES)
PROAIM 14FT JIB ARM WITH STAND 8
WARRANTY
We oer a one year warranty for our products from the date of purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
crasmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
dues are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product ,
or service by anyone other than our company.
We are not liable for incidental or consequenal damages resulng from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers aer the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. Aer that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without rst geng a response and geng the approval to send back
the item.
In case of any kind of dissasfacon, we urge you to Contact us immediately and we shall do our
best to help you out.
For any other assistance you can reach us via email.
Tabla de contenidos
Otros manuales de Accesorios para cámaras de PROAIM
PROAIM
PROAIM P-UTRA-01 Manual de usuario
PROAIM
PROAIM WS-284 Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM CAMTREE HUNT Manual de usuario
PROAIM
PROAIM Cambird Pro SL-CBPR-01 Manual de usuario
PROAIM
PROAIM Gripmag Manual de usuario
PROAIM
PROAIM P-FT-J Manual de usuario
PROAIM
PROAIM 9CTH-TMP Manual de usuario
PROAIM
PROAIM MB-10 Manual de usuario
PROAIM
PROAIM CINEMA TP-QUADO Manual de usuario
PROAIM
PROAIM DP-18 Manual de usuario
PROAIM
PROAIM QR-ELMG-01 Manual de usuario
PROAIM
PROAIM ROM-1 Manual de usuario
PROAIM
PROAIM P-PRT-D Manual de usuario
PROAIM
PROAIM Airwave Ultra Manual de usuario
PROAIM
PROAIM VI-252-00 Manual de usuario
PROAIM
PROAIM LB230 Manual de usuario
PROAIM
PROAIM Kite-22 Ultimate Package Manual de instrucciones
PROAIM
PROAIM P-L4-SL Manual de usuario
PROAIM
PROAIM SL-CNL Manual de usuario
