Primera Label Stock Manual de usuario

Switch on the

unwinder, printer

and rewinder.

2Place the label stock

roll (max 12" OD) on

the unwinder chuck.

Push the stock all the

way back until it

touches the stop disc.

Stop Disc

3The loose stock should fall on

the right side of the roll. Turn

the tension knob clockwise to

secure the roll to the chuck.

Turn the knob as as tight as

you can! Feed the stock under

the dancer arm and through

the cutter.

Dancer Arm

Cutter

Tension Knob

Continue feeding the stock

into the printer feeder tray.

Feed the stock under the green

guides and under the paper

feed roller. Stop feeding when

the leading edge of the stock

has covered the red stop block

printed just outside the feeder

door entrance.

Green Guides

Feed Roller

Red Stop Block

Place an empty label

core on the rewinder

chuck. Push the core all

the way back until it

touches the back label

guide disc.

Loading Label Stock Quick Reference Guide

Place the outer label guide

disc on to the rewinder chuck.

Push the guide until it touches

the rewinder core. Turn the

tension knob clockwise to

secure the core and the label

guide to the chuck.

Note: Some cores may be shorter

than the the stock width. If so,

make sure the distance between

the label guide discs is slightly

larger than the stock width.

Attach the label stock to the

rewinder core.

As the printer is preparing to

print, get a piece of tape ready.

It is best to stand to the right

side of printer with your arms

above the rewinder roll. As

the stock is ejected from the

printer guide it with your left

hand through the tensioner

unit. As soon as it clears the

tensioner place the tape on the

middle of the end of the stock.

The stock will continue to

feed at a slower speed.

When it reaches the

rewinder, attach it to the top

of the empty label core.

Position the stock so that it

that it is centered on the

core.

Immediately after the label stock is attached,

engage the Rewinder by flipping the

Rewinder Dancer Arm toward the printer

until it touches the paper.

Important! To minimize the slack loop that

will be created under the rewinder, it is

very important that you engage this arm

immediately after the label stock is taped

to the core.

8a 8b

070609-511223

7Print your label according to Section 5 of the manual.

Note: Depending on when the printer was last used, the fuser will need to heat up or cool down before the printer will print.

This can take from 2 seconds to 2 minutes.

4 Seconds

iImportant Note: The taping process

occurs very quickly so you may not

get the label stock attached correctly

the first time you try it. It is impor-

tant to attach the label stock centered

on the core. If the attached label

stock is too far to the right or left the

the paper may fold over itself and

cause an uneven wrap. If you think

the label stock was not attached

properly, cancel the print job using

the control panel on the front of the

printer.

Otros manuales de Accesorios de impresora de Primera

Primera

Primera ADL-MAX Manual de usuario

Primera

Primera OptiVault Manual de usuario

Primera

Primera Impressa 3 Manual de usuario

Primera

Primera LX400 Manual de usuario

Primera

Primera Signature II Especificaciones

Primera

Primera AP-CODE Manual de usuario

Primera

Primera Bravo Pro Manual de usuario

Primera

Primera Disc Autoloader ADL-MAX Manual de usuario

Primera

Primera Bravo II Manual de instrucciones

Primera

Primera PN 510725-121304 Especificaciones

Primera

Primera Bravo Pro Manual de usuario

Primera

Primera Conductor Conductor Printer Manual de usuario

Primera

Primera LX-REWINDER Manual de usuario

Primera

Primera Bravo II Manual de usuario

Primera

Primera Ink Jet Printers Manual de usuario

Primera

Primera OptiVault Manual de usuario

Primera

Primera RW-12 Manual de usuario

Primera

Primera OptiVault Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual