Prime Design FBM-1061 Manual de usuario

Pages 2-4 Packaging Contents

Pages 5–8 FBM Mounting

Page 9 Mounting to OTC Channels

Pages 9–11 Installing Mount Braces

OTC Mounting System–Standard Height Service Body, Flip Top Lid Model

PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118

Toll Free: 1.8.PRIME.RACK ▪ Fax: 651-552-1799 ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

2

FBM-1061 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

CONTENTS OVERVIEW

Front Base Mounting Leg...................................... (Qty 2)

Rear Base Mounting Leg ...................................... (Qty 2)

Crossbar Mounting Brace..................................... (Qty 2)

Channel Mounting Brace...................................... (Qty 4)

Mounting Leg Connector Assembly ..................... (Qty 4)

Rear Mounting Leg Bracket.................................. (Qty 2)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

3

FBM-1061 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

Anti-Seize

Lock Washer (6X)

Crossbar Mounting Connector (4X)

M8 x 45MM (2X)

M8 x 30MM (8X)M8 x 20MM (2X)

M8 x 60MM Carriage Bolt (2X)

M8 x 55MM (6X)

M8 Lock Nut (10X) " Flat Washer (16X)

Fender Washer

(8X)

Rubber Washer

(8X)

M8 Nut Bracket (6X)

HKT-8065 Front Mount Hardware Kit

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

4

FBM-1061 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

Anti-Seize

Lock Washer (4X)

M8 x 45MM (2X)M8 x 30MM (10X) M8 x 55MM (2X)

M8 x 70MM (4X)

M8 Lock Nut (14X) " Flat Washer (22X)

Fender Washer

(10X)

Rubber Washer

(10X)

M8 Nut Bracket (4X)

HKT-8064 Rear Mount Hardware Kit

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

5

FBM-1061 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS

OVERVIEW: MOUNTING TO OTC CHANNELS

NOTE: Channels and Crossbars in this Overview are shown

for reference only. Specic congurations are determined

by Service Body size, and Crossbar preferences.

2.11Install Mounting Leg Connectors onto the Base Mounting

Legs as shown.

Install Rear Mounting Leg Brackets onto the Rear Mounting

Legs as shown and torque to 90 in-lbs.

Remove and

retain Hardware

LEG CONNECTORSREAR MOUNTING LEG BRACKETS

Align outer Connector hole with

the bolt hole on the Mounting Leg

for Hardware re-installation.

M8 x 70MM

Flat Washer

Locknut

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

6

FBM-1061 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS

2.2 Re-install Mounting Leg Connector Hardware as shown. FRONT MOUNTING LEGS

Right and Left

Front Legs Aligned

3.1

Install Front Mounting

Legs onto the front inside

corner of your service body

as shown.

NOTE: Depending on the application,

isolation tape (not included) may be

required to prevent the chance of

bimetallic corrosion.

FRONT MOUNTING LEG

DRILLING & BOLT SIZING

NOTE: Parts of the utility body are

cutaway for illustrative purposes

M8 x 30MM and M8 x 55MM available the

thickness of your utility body. Drill and attach

hardware as needed according to your utility

body’s OEM specications.

Front Passenger Side

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

7

Flat Washer

Locknut

Rubber Washer

Fender Washer

Flat Washer

Locknut

Rubber Washer

Fender Washer

FBM-1061 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS

FASTENING FRONT MOUNTING LEGS

M8 x 30MM

(Lower)

M8 x 30MM

(Lower)

M8 x 55MM

(Upper)

M8 x 30MM

(Upper)

3.2 Install Hardware with the appropriate bolt size needed

for your service body. Torque to 90 in-lbs.

NOTE: Parts of the utility body are

cutaway for illustrative purposes

Example shown with uitlity body requiring the

M8 x 55MM bolts in the upper drilling locations.

Front Passenger Side

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

8

FBM-1061 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS

REAR MOUNTING LEGS

M8 x 30MM

Align Front and

Back Legs

Flat Washer

Aligned with

Front Leg

Must clear Rear

Light and features

Locknut

Rubber Washer

Fender Washer

Avoid Rear Light

4.1

4.2

4.3 4.4

Install Rear Mounting Legs onto the outside rear of your

service body as shown.

Ensure alignment and light clearance

as shown below.

NOTE: Depending on the application,

isolation tape (not included) may be

required to prevent the chance of

bimetallic corrosion.

NOTE: Refer to OEM recommendations for the instllation of a

support or backing plate behind the mounts.

Install Hardware as shown and torque

to 90 in-lbs.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

9

FBM-1061 ASSEMBLY INSTRUCTIONS-MOUNTING TO OTC CHANNELS

MOUNTING TO CHANNELS

Torque all Mounting Bracket

bolts to 90 in-lbs

Crossbars must be installed directly

over the the rear and front mounts.

5.1 Loosen all indicated Nuts to

install the Channels. Do not

tighten until Step 5.3. 5.3

5.2

REAR MOUNTING FOOT

NUT BRACKETS

FRONT MOUNTING FOOT

NUT BRACKETS

6.1 Install one M8 Nut Bracket in each rear

Mounting Foot channel as shown. 6.2 Install one M8 Nut Bracket in each front

Mounting Foot channel as shown.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

10

FBM-1061 ASSEMBLY INSTRUCTIONS-INSTALLING MOUNT BRACES

MOUNTING LEG–CHANNEL

BRACE INSTALLATION

Keep Nut Bracket

loose for installation

into inner Channel sides

M8 x 45MM

Lock Washer

Flat Washer

M8 x 55MM

Lock Washer

Flat Washer

7.3 Install the lower end of

the Braces into the Mounting

Foot channels using the

Nut Brackets installed

in Steps 6.1–6.2,

and Hardware

as shown. Torque to

90 in-lbs.

7.1

*Holes must align

7.2 Install Braces into the inside of the Channels as shown.

ADDITIONAL FRONT MOUNTING

FOOT NUT BRACKETS

8Install a second M8 Nut Brackets in each

front Mounting Foot channel as shown.

Prime Design FBM-1061 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas