Powerware 9170+ Manual de usuario

9170

USER’S GUIDE

UPS

3–18 kVA,

50 and 60 Hz

www.powerware.com

Requesting a Declaration of Conformity

Units that are labeled with a CE mark comply with the following harmonized standards and EU

directives:

쑺Harmonized Standards: EN 50091-1-1 and EN 50091-2; IEC 950 Third Edition

쑺EU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage

limits

93/68/EEC, Amending Directive 73/23/EEC

89/336/EEC, Council Directive relating to electromagnetic compatibility

92/31/EEC, Amending Directive 89/336/EEC relating to EMC

The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of

the EC Declaration of Conformity, contact:

Powerware Corporation

Koskelontie 13

FIN-02920 Espoo

Finland

Phone: +358-9-452 661

Fax: +358-9-452 665 68

Powerware is a registered trademark and ConnectUPS and BestDock are trademarks of Powerware

Corporation.

be reproduced in any way without the express written approval of Powerware.

Class A EMC Statements

FCC Part 15

NOTE This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

ICES-003

This Class A Interference Causing Equipment meets all requirements of the Canadian Interference

Causing Equipment Regulations ICES-003.

Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel

brouilleur du Canada.

EN 50091-2

Some configurations are classified under EN 50091-2 as “Class-A UPS for Unrestricted Sales

Distribution.” For these configurations, the following applies:

WARNING This is a Class A-UPS Product. In a domestic environment, this product may cause radio

interference, in which case, the user may be required to take additional measures.

VCCI Notice

Powerware®9170+UPS User’s Guide SRev B www.powerware.com

Table of Contents

1Introduction 1................................................

Safety Warnings 2...........................................................

Physical Features 3..........................................................

2 Installation Setup 7............................................

Equipment Clearances 7......................................................

Location Requirements 8.....................................................

UPS Setup 8................................................................

Three- and Six-Slot Cabinets 8..............................................

Nine- and Twelve-Slot Cabinets 9...........................................

Caster Cart Installation 10.....................................................

Stabilizer Bracket Installation (Twelve-Slot Cabinet Only) 11.........................

Rack-Mount Installation (Three- and Six-Slot Cabinet) 12...........................

Floor Anchor Kit Installation 14................................................

Moving the Cabinets 16.......................................................

3 UPS with Bypass Electrical Installation 19.........................

Input Current Ratings 21......................................................

Bypass Switches 22...........................................................

UPS Installation with an External Bypass Switch 25.................................

System Wiring Diagrams 32....................................................

4 UPS Electrical Installation 37....................................

Input Current Ratings 38......................................................

UPS Electrical Installation 40...................................................

System Wiring Diagrams 46....................................................

5 Isolated Output Wiring Diagrams 51.............................

Neutral-to-Ground Bonding for Isolated Output 52................................

System Wiring Diagrams 54....................................................

Table of Contents

ii Powerware®9170+UPS User’s Guide SRev B www.powerware.com

6 Battery Cabinet Installation 57..................................

7 UPS Startup 63.................................................

Power and Battery Module Installation 64........................................

Startup for Plug-Receptacle Units 65............................................

Startup for Hardwired Units 68.................................................

Initial Startup Parameters 72...................................................

8Operation 75...................................................

Turning the UPS On 77........................................................

Removing Input Power 77.....................................................

Front Panel Display 78........................................................

Using the Front Panel Display 79................................................

Parameters 81...............................................................

Changing Parameter Settings 81................................................

Reading the Powerware 9170+ System Logs 81....................................

Inverter Log 82............................................................

Alarm Log 83.............................................................

Battery Test 84..............................................................

Menu Map 84...............................................................

9 Communication 87.............................................

LanSafe Power Management Software 87........................................

Optional Interface Kits 87.....................................................

Communication Slots 88......................................................

ConnectUPSt Web/SNMP Card (BD Model) 88..................................

Relay Interface Card (BestDock Model) 88.....................................

Dedicated Input Signals 88....................................................

DB-9 Communication Port 90..................................................

10 Maintenance 91................................................

Routine Maintenance 91......................................................

Storage Temperature 92......................................................

External Bypass Switch (Make-Before-Break Only) Operation 92.....................

Battery Replacement 93.......................................................

Power Module Replacement 94.................................................

Table of Contents

iii

Powerware®9170+UPS User’s Guide SRev B www.powerware.com

11 Specifications 95...............................................

12 Troubleshooting 103.............................................

Alarms 105...................................................................

Service and Support 109.......................................................

Table of Contents

iv Powerware®9170+UPS User’s Guide SRev B www.powerware.com

Powerware®9170+UPS User’s Guide SRev B www.powerware.com

Chapter 1 Introduction

The Powerware 9170+uninterruptible power system (UPS) is a modular

UPS that contains battery modules and power control modules (referred

to as power modules). These modules plug into a rack cabinet structure

containing additional control, communication, and display functions that

enable integrated control of all power modules. The UPS is housed in a

single cabinet, with extra battery capacity housed in auxiliary battery

cabinets.

The pluggable power modules can be removed and replaced

(hot-swapped) without powering the UPS down if the UPS has sufficient

redundant capacity. Battery modules may also be hot-swapped for

maintenance. Power control circuitry in the cabinet senses problems in

power modules, and automatically transfers control and load to the

remaining power modules.

All power modules share the load requirements equally. For example,

three power modules are capable of supplying a total of 9 kVA. If a load

requires only 4.5 kVA, each power module supplies 1.5 kVA to the

output. If one power module is removed or for some reason fails, each

of the two remaining power modules would supply half of the load, or

2.25 kVA. In other words, redundancy exists when the load can be

supplied by less than all of the installed power modules.

TheUPScanbeconfiguredwithuptosevenpowerand/oroptional

battery charger modules; its output is limited such that an excess number

of power modules allow the failure of one or more modules without

causing the UPS to lose any functionality.

To permit UPS removal from the power path, while maintaining power to

the loads, an external bypass switch is required. This switch is optional

but recommended for system serviceability.

Introduction

2Powerware®9170+UPS User’s Guide SRev B www.powerware.com

Safety Warnings

Read the following precautions before you install the UPS.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during

installation and maintenance of the UPS and batteries. Please read all

instructions before operating the equipment and save this manual for future

reference.

CAUTION

쑺Split-phase power modules (model ASY-0673) have brown labels on the

front and produce two output voltages: 100/100 for 200, 110/110 for 220,

120/120 for 240, 120/120 for 208, or 127/127 for 220 Vac. Universal power

modules (model ASY-0674) have black labels on the front and produce a

single output voltage: 200, 208, 220, 230, or 240 Vac. DO NOT mix the two

types of power modules in the same Powerware 9170+cabinet.

쑺Do NOT install more than seven power and/or optional battery charger

modules in the system.

쑺Battery modules to be used in the Powerware 9170+system are model

ASY-0529. Each battery module weighs 30 lb (14 kg). Use care in lifting and

moving battery modules.

쑺All input and output wiring must be copper and adequate to carrying

currents as listed in Table 16 and Table 17 on pages 97 and 99.

쑺Torque all bolts holding input and output power conductors to values

specified in Table 2 on page 22.

쑺The user is required to provide power input and output disconnect devices

for the UPS. These must be within sight of the UPS and easily accessible. For

a plug-receptacle unit, the plug serves as the power input disconnect device,

which must also be readily accessible.

Otros manuales para 9170+

Tabla de contenidos

Otros manuales de Unión Postal Universal de Powerware

Powerware

Powerware 9315 Manual de usuario

Powerware

Powerware 9320 Manual de usuario

Powerware

Powerware 9305 HS Series Manual de funcionamiento

Powerware

Powerware 5119 Manual de usuario

Powerware

Powerware 9125 Manual de usuario

Powerware

Powerware 9125 Manual de usuario

Powerware

Powerware UPS 1000 - 2200 Manual de usuario

Powerware

Powerware 5105 Manual de usuario

Powerware

Powerware 3105 Manual de usuario

Powerware

Powerware 3110 Manual de usuario

Powerware

Powerware 9170+ Manual de usuario

Powerware

Powerware P93 Manual de usuario

Powerware

Powerware 300 VA Manual de usuario

Powerware

Powerware Uninterruptible Power Supply Manual de usuario

Powerware

Powerware 9330 Manual de usuario

Powerware

Powerware BPIV 30 kVA Manual de usuario

Powerware

Powerware Ferrups FE/QFE 500VA Manual de usuario

Powerware

Powerware 9125 PowerPass Manual de usuario

Powerware

Powerware 9390 Manual de usuario

Powerware

Powerware 9910 p Series Manual de usuario

Powerware

Powerware 9315s Manual de usuario

Powerware

Powerware 9315 Manual de usuario

Powerware

Powerware 9125 Manual de usuario

Powerware

Powerware Plus 80 Manual de instrucciones

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario