PowerWalker VFI 1000 AT Manual de usuario
1
ENGLISH
PowerWalker VFI 1000-3000 AT
Quick Guide
LCD Panel
The UPS has an LCD panel with 6 pages to scroll.
Left side: Input Voltage
[V]
Right side: Output
Voltage [V]
Left side: Input frequency [Hz]
Right side: Output frequency
[Hz]
Left side: Load level [%]
Right side: Load in kW
Left side: Load level [%]
Right side: Load in kVA
Left side: Battery capacity [%]
Right side
: Battery voltage
[VDC]
Left side: Backup Time [min]
Right side:
Battery voltage
[VDC]
Modes and warnings
Operation
mode
LCD display Description
Line Mode
Outlets supplied with power. Batteries are charged.
Battery
The unit provides output power from battery.
ECO mode[1]
When the input voltage is within set range, UPS
bypasses input to output for energy saving. [1]
Bypass[2]
UPS bypasses voltage to output.
2
ENGLISH
Converter[3]
The UPS is set to a constant frequency of 50Hz or
60Hz if the input frequency is within range. [3]
Standby
Output is switched off. The batteries are charged.
EPO
Emergency Power Off – the UPS output is turned
off.
Fault
The UPS is in fault mode because of short-circuit on
the output.
Units defining the numeric value: percentage,
kilowatt, volt-ampere, minute, hertz
Fault
Sound disabled
Rear panel view
13
ENGLISH
1. Power On/Off button
2. Function buttons
3. Display
4. AC Input
5. Input Circuit Breaker
6. EPO (Emergency Power
Off) Connector
7. USB port
8. Serial Port
9. Extension slot
10. Output sockets
11. Battery Pack connector
12. Output Terminal Block
Battery Pack connection
1.
Input connector
2. Fuse Board
3. Output connector
Battery Packs are connected in parallel. Grounding
wire must be fixed to the housing.
14
ENGLISH
Communication connection
USB port
RS232 port
Extension Slot
Apart from standard USB Port, the UPS is equipped with RS-232. Those two ports do not work
at the same time.
Button control
The ON button
•Press this button to turn on the UPS.
•In line mode, ECO mode or converter mode, press the button for 5 seconds to activate
the battery test.
The OFF button
•Press this button to turn off UPS.
Enter button
•Press this button for 5 seconds to get into setting mode while in bypass mode or standby
mode.
•In setting mode, click this button to confirm selection, or press this button for 5 seconds
to save the changes and exit the setting mode.
•Press this button to scroll up in the LCD menu.
ESC button
•In setting mode, click this button to display next selection or press this button for 5
seconds to exit setting mode without saving changes.
•Press the button for 5 seconds to disable and enable buzzer alarm.
•Press this button to scroll down in the LCD menu.
Enter + ESC buttons
•Switch to bypass mode: When the main power is normal, press these two buttons
simultaneously for 5 seconds, the UPS will enter bypass mode.
UPS Setting
15
ENGLISH
1. Setting Item
2. Setting Value
3. Additional Icon
item Configure submenu Available Settings
001 Output Voltage =[208V] [220V] [230V] [240V]
002
Output Frequency
= [50.0Hz] [60.0Hz]
003 ECO Mode[1] input voltage
range [0%] (Disabled) [10%] [15%] (Enabled)
004
Bypass Mode
[2]
[DIS] (Disabled) [ENA] (Enabled)
005
Converter Mode
[3]
[CF DIS] (Disabled) [CF ENA] (Enabled)
006 EPO/ROO[4] [EPo] /[Roo]
007
Quantity of Battery Packs
[5]
[0bP]/[1bP]/[2bP]/[3bP]
008 Bypass when UPS is Off [DIS] (Disabled) [ENA] (Enabled)
009
Buzzer
[DIS] (Disabled) [ENA] (Enabled)
Default settings are marked bold.
Event description and troubleshooting
Event
Description
E11, E12, A62
Various issues related to batteries. Please check if batteries are connected
and they are in good condition.
E14
Issue related to the load. Check if there is no short-circuit or excessive load.
Test the UPS without the load.
E18, E19, A68
Issues related to overheating or fan failure. Please check that the fan is
rotating, ventilation holes are not covered and the ambient temperature is
within norm.
EPO
Missing EPO connection.
Technical Specification
MODEL
1000
2000
3000
CAPACITY
1000 VA / 900 W
2000 VA / 1800 W
3000 VA / 2700 W
INPUT
Voltage Range
80-300V for 0-30% load
120-300V for 30-60% load
140-300V for 60-80% load
160-300V for 80-100% load
80-300V for 0-30% load
140-300V for 30-60%
160-300V for 60-80%
190-300V for 80-100%
all values are ±5%
Frequency Range
40Hz ~ 70 Hz
16
ENGLISH
Power Factor
0.99 @ nominal voltage (input voltage)
OUTPUT
Output voltage 208/220/230/240VAC
ECO Mode Voltage[1] Adjustable ±10% or ±15%
AC Voltage Regulation
±1% (Batt. Mode)
Frequency Range
(Synchronized Mode)
Adjustable 1-10% (default ±8%)
Outside of the range, it switches to converter mode
Frequency Range (Batt.
Mode)
50/60 Hz ± 0.5 Hz
Overload
Line Mode: warning @ 100-110%; bypass after 60s @ 110-120%;
bypass immediately @ >120%
Battery Mode: warning @ 100-110%; shutdown after 10s @ 110-
120%; shutdown immediately @ > 120%
Current Crest Ratio
3:1
Harmonic Distortion
<3 % THD (linear load); < 5 % THD (non-linear load)
Transfer Time
Zero
Waveform (Batt. Mode)
Pure Sinewave
Efficiency
Energy saving technology. ECO mode over 95%
Protection
UPS output cut off immediately or input fuse.
Surge protection IEC 61000-4-5 level 4
BATTERY
Numbers
2 x 9Ah
4 x 9Ah
6 x 9Ah
Recharge Time
4 hours recover to 90% capacity (Typical)
Battery Pack
Battery Pack Connector available[5]
PHYSICAL
Dimension, W x H x D
(mm)
140 x 191 x 327
151 x 225 x 390
196 x 342 x 416
Net Weight (kgs)
14.5
17.14
21.3
Operation Humidity
20-90 % RH @ 0- 40°C (non-condensing)
MANAGEMENT
Smart RS-232 or USB
Supports Windows®, Linux, Unix, macOS and HID support for USB
Software
PowerMaster available at powermaster.powerwalker.com
Optional SNMP
Power management from SNMP manager and web browser
[1] ECO Mode offers higher efficiency in line mode, but transfer time is not guaranteed to be
0ms.
[2] When bypass is disabled, the UPS will not turn on to bypass in case of overload or fault.
[3] The load capacity will be derated to 60%. ECO Mode, Bypass Mode are disabled (regardless
of the settings)
[4]If ROO (Remote On/Off) is enabled, UPS can be turned on/off by the ROO port (opened
circuit turns off; closed circuit turns on). EPO (Emergency Power Off) only turns off the UPS’
output. After closing the circuit UPS needs to be manually turned on.
[5] UPS cannot detect the number of Battery Packs, so this setting is essential. If BP is 1-3, the
charger current is increased to 4A.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Unión Postal Universal de PowerWalker
PowerWalker
PowerWalker VFI 20000-40000TAP 3/3 BI Manual de usuario
PowerWalker
PowerWalker VI 1000 Manual de usuario
PowerWalker
PowerWalker VFI 1000T/E LCD Manual de usuario
PowerWalker
PowerWalker VFI 10000CP 3/3 Manual de usuario
PowerWalker
PowerWalker VFD 400 Manual de usuario
PowerWalker
PowerWalker VI 500 R1U Manual de usuario
PowerWalker
PowerWalker VI SCL Series Manual de usuario
PowerWalker
PowerWalker VFI 6000 CG PF1 Manual de instalación y operación
PowerWalker
PowerWalker VI CW Series Manual de usuario
PowerWalker
PowerWalker VI 3000RT LCD Manual de usuario
PowerWalker
PowerWalker VI 750 PSW Manual de usuario
PowerWalker
PowerWalker VI 500T/HID Manual de usuario
PowerWalker
PowerWalker PowerWalker VFI 10000RT LCD Manual de usuario
PowerWalker
PowerWalker VFI 3000T LCD Manual de usuario
PowerWalker
PowerWalker VFI 3000 LCD Guía de instalación
PowerWalker
PowerWalker VI 1200 RLE Manual de usuario
PowerWalker
PowerWalker VI 650 GX Manual de usuario
PowerWalker
PowerWalker VFI ICT IoT Series Manual de usuario
PowerWalker
PowerWalker 650 SH Manual de usuario
PowerWalker
PowerWalker VFI 10K CPH Manual de usuario
Manuales populares de Unión Postal Universal de otras marcas
Pylontech
Pylontech Victron & Pylontech US5000 Manual de usuario
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario
Mecer
Mecer ME-1000-WTU Manual de usuario
Mustek
Mustek PowerMust 530(B) Plus Manual de instalación y operación
Emerson
Emerson Liebert NXL series Manual de usuario
MAKELSAN
MAKELSAN BOXER SERIES Manual de usuario
