PowerWalker VI 400 SC Manual de usuario

Line Interactive UPS

PowerWalker VI 400 SC

PowerWalker VI 600 SC

PowerWalker VI 800 SC

PowerWalker VI 1000 SC

PowerWalker VI 1500 SC

PowerWalker VI 2000 SC

Quick Start Guide

EN/DE/FR/ES/IT/PT/SE/FI/NO/TR

RU/UA/BY/PL/CZ/HR/HU/BG/KZ/SR

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS –This manual contains important instructions for models

PowerWalker VI 400/600/800/1000/1500/2000 SC that should be followed during installation

and maintenance of the UPS and batteries.

This product is specially designed for PCs and it is not recommended for use in any life-

supporting system and other specific important equipment.

This equipment can be operated by any individual with no previous training.

Do not plug household appliances such as hair dryers to UPS receptacles.

This unit intended for installation in a controlled environment (temperature controlled,

indoor area free of conductive contaminants). Avoid installing the UPS in locations where

there is standing or running water, or excessive humidity.

Risk of electric shock, do not remove cover. No user serviceable parts inside. Refer

servicing to qualified service personnel.

The utility power outlet shall be near the equipment and easily accessible. To isolate UPS

from AC input, remove the plug from the utility power outlet.

If UPS is to be stored for a long time, it is recommended to recharge the batteries (by

connecting the utility power to UPS, switch “ON”), once a month for 24 hours to avoid a

full battery discharge.

Please do not use the UPS in excess of the rated load capacity.

The UPS contains one/two large-capacity batteries. So the shell shall not be opened,

otherwise such dangers as electric shock will be caused. If any internal overhaul or

replacement of the battery is required, please contact the distributor.

The internal short circuiting of the UPS will lead to dangers such as electric shock or fire,

therefore, no water containers (such as a water glass) shall be placed on the top of the

UPS so as to avoid such dangers as electric shock.

Do not dispose of battery or batteries in a fire. The battery may explode.

Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the

skin and eyes. It may be toxic.

Icon Φon the rating label stands for phase symbol.

A battery can present a risk of electrical shock and high short circuit current. The

following precautions should be observed when working on batteries :

Remove watches, rings, or other metal objects from the hand.

Use tools with insulated handles.

Servicing of batteries should be performed or supervised by personnel knowledgeable of

batteries and the required precautions. Keep unauthorized personnel away from

batteries.

When replacing batteries, replace with the same type and number of the sealed lead-acid

batteries.

The maximum ambient temperature rating is 40°C.

This pluggable type A equipment with battery already installed by the supplier is

operator installable and may be operated by laymen.

During the installation of this equipment it should be assured that the sum of the leakage

currents of the UPS and the connected loads does not exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from

the mains, hazardous voltage still may be accessible through supply from battery. The

battery supply should be therefore disconnected in the plus and minus pole of the

battery when maintenance or service work inside the UPS is necessary.

The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be

easily accessible.

In case smoke is found coming out from the device, please cut off the power supply

quickly and contact the distributor.

Do not keep or use this product in any of the following environments:

oAny area with combustible gas, corrosive substance or heavy dust.

oAny area with extraordinarily high or low temperature (above 40˚C or below

0˚C) and humidity of more than 90%.

oAny area exposed to direct sunshine or near any heating apparatus.

oAny area with serious vibrations.

oOutdoor.

In the event that there is fire occurring in the vicinity, please use dry-power extinguishers.

The use of liquid extinguishers may give rise to the danger of electric shock.

This product complies with the safety and environmental regulations in EU.

If the time arises to throw away your product, please recycle all the components possible. Batteries

and rechargeable batteries are not to be disposed in your domestic waste! Please recycle them at

your local recycling point. Together we can help to protect the environment.

1. Introduction

PowerWalker VI 400/600/800/1000/1500/2000 SC is an intelligent and compact line interactive UPS

(Uninterruptible Power Supply) which is designed to protect your personal computer or sensitive

electronic equipments from all forms of power interference, including complete power failures. It is

equipped with many features that allow any attached equipment to operate longer and with more

reliability.

2. Green concept design

PowerWalker VI 400/600/800/1000/1500/2000 SC series adopt switching mode charging which

creates a variety of benefits:

Increases charging efficiency to more than 80%, more energy saving than traditional UPS

The battery requires only 4 hours to be 90% charged, reducing 50% of charging time

Reduces heat generation during battery charging, providing a longer battery life

Increases reliability and helps to save money

3. Package Contents

You should have received the following items inside of package:

UPS Unit

AC Input Power Cord

(for PowerWalker

1500/2000 SC only)

Quick Start Guide

Service Guide

4. Product Overview

Front Panel:

INDICATORS

1x LED

3x LED

AC Mode

Green lighting

Battery Mode

Green flashing

Yellow flashing

Fault

N/A

Red lighting

Back Panel:

PowerWalker 400/600/800 SC

PowerWalker 1000 SC

Output receptacles

AC input

Modem or phone

surge protection

USB port

Breaker

PowerWalker 1500/2000 SC



5. Installation and Initial Startup

Before installation, please inspect the unit. Be sure that nothing is damaged.

I: Placement & Storage Conditions

Install the UPS in a protected area that is free of excessive dust and has adequate air flow. Please

place the UPS away from other units at least 20 cm to avoid interference. Do NOT operate the

UPS where the temperature exceeds 0-40°C and the humidity is over 0-90 % RH.

II: Connect to Utility and Charge

Plug in the AC input cord to the wall outlet. For the best results, we suggest charging the battery

at least 4 hours before initial use. The unit charges its battery while connecting to the utility.

III: Connect the Loads

Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power

switch of UPS unit, and devices connected to the UPS will be protected by UPS unit.

Do not attach a power strip or surge suppressor to the UPS.

IV: Connect Modem or Phone for Surge Protection

Connect a single modem or phone line into surge-protected “IN” outlet on the back panel of the

UPS unit. Connect from “OUT” outlet to the computer with another phone line cable.

V: Connect USB Cable

To monitor the UPS status, such as unattended UPS shutdown and start-up, by using bundled

software, please connect the UPS and PC with USB cable included.

VI: Turn On/Off the Unit

Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again the

power switch.

6. Audible alarm from the UPS

When UPS switches from AC mode to Battery Mode to back up power supply: sounding

every 10 seconds

When battery is low: sounding every second

When UPS is overloaded: sounding every 0.5 second

When battery is faulty: sounding every 2 seconds

Other fault: Continuous sounding

7. Software Installation on your PC

Please download the newest software from http://viewpower.powerwalker.com. Then, follow

the on-screen instructions to install the software ViewPower.

After the software is successfully installed, the communication with UPS has been established

and an orange icon will appear in the system tray.

Double-click the icon to use the monitor (as above).

You can schedule UPS shutdown/start-up and monitor UPS status through PC.

Detail instructions please refer to the e-manual in the software.

NEVER connect a laser printer or scanner to

the UPS unit because in-rush current generated by

motor’s devices may cause the damage of the unit

8. Specifications

Model

PowerWalker 400 SC

PowerWalker 600 SC

PowerWalker 800 SC

CAPACITY

400 VA / 240 W

600 VA / 360 W

800 VA / 480 W

INPUT

Voltage

230 VAC

Voltage Range

162-290 VAC

Frequency Range

60/50 Hz (Auto Sensing)

OUTPUT

Voltage Regulation

+/-10%

Transfer Time

Typical 2-6 ms

Waveform

Simulated Sine Wave

BATTERY

Type & Number

12V / 4.5Ah x 1

12V/ 7Ah x 1

12V/ 9Ah x 1

Charging Time

4 hours recover to 90% capacity

Protection

Overload, discharge, and overcharge protection

INDICATORS

AC Mode

Green lighting

Battery Mode

Green flashing

Fault

N/A

PHYSICAL

Dimension (DxWxH)

279mm x 101mm x 142mm

Net weight (kgs)

3.55

4.2

4.9

ENVIRONMENT

Humidity

0-90 % RH @ 0-40°C (non-condensing)

Noise Level

Less than 40 dB

Model

PowerWalker 1000 SC

PowerWalker 1500SC

PowerWalker 2000 SC

CAPACITY

1000 VA / 600 W

1500 VA / 900 W

2000 VA / 1200W

INPUT

Voltage

230 VAC

Voltage Range

162-290 VAC

Frequency Range

60/50 Hz (Auto Sensing)

OUTPUT

Voltage Regulation

+/-10%

Transfer Time

Typical 2-6 ms

Waveform

Simulated Sine Wave

BATTERY

Type & Number

12V / 7Ah x 2

12V/ 9Ah x 2

Charging Time

4-6 hours recover to 90% capacity

Protection

Overload, discharge, and overcharge protection

INDICATORS

AC Mode

Green lighting

Battery Mode

Green flashing

Yellow flashing

Fault

N/A

Red lighting

PHYSICAL & ENVIRONMENT

Dimension (DxWxH)

320mm x 130mm x 182mm

Net weight (kgs)

8.2

10.4

10.6

Humidity

0-90 % RH @ 0-40°C (non-condensing)

Noise Level

Less than 40 dB

Line Interactive USV

PowerWalker VI 400 SC

PowerWalker VI 600 SC

PowerWalker VI 800 SC

PowerWalker VI 1000 SC

PowerWalker VI 1500 SC

PowerWalker VI 2000 SC

Schnellanleitung

EN/DE/FR/ES/IT/PT/SE/FI/NO/TR

RU/UA/BY/PL/CZ/HR/HU/BG/KZ/SR

WICHTIGE SICHERHEITSHINWEISE

BEWAHREN SIE DIESE BEDIENUNGSANLEITUNG SORGFÄLTIG AUF –Diese enthält wichtige

Anleitungen für die Modelle PowerWalker VI 400/600/800/1000/1500/2000 SC, die während

der Installation und Wartung der USV und der Akkus beachtet werden sollten.

Dieses Produkt wurde speziell für PC’s entwickelt und wird nicht für den Einsatz wie etwa

für Lebenserhaltungssysteme und andere wichtige Geräte empfohlen.

Dieses Gerät kann von Jedermann ohne vorherige Ausbildung betrieben werden.

Schließen Sie keine Haushaltsgeräte, wie etwa Haartrockner, an die Steckdosen der USV

an.

Dieses Gerät ist für die Installation in einer kontrollierten Umgebung ausgelegt (d. h.

geregelte Temperatur, Innenbereich, der frei von schädlichen Substanzen ist). Vermeiden

Sie die Installation der USV an einem Ort mit fließendem Wasser oder übermäßiger

Feuchtigkeit.

Decken Sie das Gerät nicht ab, da dadurch Gefahr eines elektrischen Schlages besteht. Es

befinden sich im Inneren des Geräts keine zu wartenden Teile. Lassen Sie das Gerät nur

von qualifiziertem Fachpersonal warten oder reparieren.

Die Steckdose, in der die USV eingesteckt wird, sollte gut zugänglich sein und sich in der

Nähe des Geräts befinden. Um die USV von der Wechselspannung zu trennen, ziehen Sie

bitte den Stecker aus der Steckdose.

Wenn die USV für längere Zeit gelagert werden soll, wird empfohlen, die Batterien

aufzuladen, indem die USV mit einer Steckdose verbunden und der Schalter eingeschaltet

wird. Dies sollte ein Mal pro Monat für 24 Stunden durchgeführt werden, um eine

vollständige Entladung der Batterie zu vermeiden.

Ü berlasten Sie die USV bitte nicht, beachten Sie die zulässige Nennlast des Geräts.

Die USV beinhaltet einen/zwei Akkus mit hoher Kapazität. Deshalb sollte das Gehäuse der

USV nicht geöffnet werden, um Gefahren von elektrischen Schlägen zu vermeiden. Wenn

der Akku repariert oder ersetzt werden muss, kontaktieren Sie bitte den Händler.

Kurzschlüsse im Inneren der USV führen zu elektrischen Schlägen oder zu Bränden,

deshalb sollten Behälter mit Wasser (z. B. ein Wasserglas) nicht auf das Gehäuse der USV

abgestellt werden.

Werfen Sie die Batterie(n) nicht in offenes Feuer. Der Akku kann explodieren.

Ö ffnen oder zerstören Sie den Akku nicht. Freigesetzter Elektrolyt kann Haut und Augen

schädigen. Er kann giftig sein.

Das Symbol Φ auf dem Typenschild steht für das Phasensymbol.

Ein Akku kann einen elektrischen Schlag oder einen hohen Kurzschlussstrom

verursachen. Die folgenden Vorsichtsmaßnahmen sollten getroffen werden, wenn mit

Akkus gearbeitet wird:

Entfernen Sie Uhren, Ringe oder andere Metallgegenstände von Ihrer Hand.

Verwenden Sie Werkzeuge mit isolierten Griffen.

Wartung und Reparatur der Akkus darf nur von Fachpersonal durchgeführt oder

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de PowerWalker

PowerWalker

PowerWalker 6000C LCD Manual de usuario

PowerWalker

PowerWalker VFI 1000-3000 CG PF1 Manual de usuario

PowerWalker

PowerWalker VI 500T/HID Manual de usuario

PowerWalker

PowerWalker VFI 10000CRM LCD Manual de usuario

PowerWalker

PowerWalker VFD 400 Manual de usuario

PowerWalker

PowerWalker VFI RT HID Series Manual de usuario

PowerWalker

PowerWalker VFI 10000 CPE 3/3 Manual de usuario

PowerWalker

PowerWalker VFI 2000 RMG/S PF1 Manual de usuario

PowerWalker

PowerWalker VFI 6000 AT Manual de usuario

PowerWalker

PowerWalker VFI 6000T LCD L Manual de usuario

PowerWalker

PowerWalker PowerMust 6054 Manual de usuario

PowerWalker

PowerWalker VFI 1000 RMG PF1 Manual de usuario

PowerWalker

PowerWalker VFI 3000 LCD Guía de instalación

PowerWalker

PowerWalker VFI 1000 R1U Manual de usuario

PowerWalker

PowerWalker Basic VI SB Series Manual de usuario

PowerWalker

PowerWalker VI 400 SE Manual de usuario

PowerWalker

PowerWalker VI THID Series Manual de usuario

PowerWalker

PowerWalker VI 1000 Manual de usuario

PowerWalker

PowerWalker VI SCL Series Manual de usuario

PowerWalker

PowerWalker VI 1000 Manual de usuario

PowerWalker

PowerWalker VFI 10K-80K CPG 3 Manual de usuario

PowerWalker

PowerWalker VFI 3/3 Series Manual de usuario

PowerWalker

PowerWalker VFD 600 APFC Manual de usuario

PowerWalker

PowerWalker BP P96T Guía del administrador

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario