PowerWalker VI RT HID Series Manual de usuario

ENGLISH

Assembly of VI/VFI RT HID Series

I. Installing the UPS

ENGLISH

II. Connecting the EBM in Tower form:

1. Slide down the UPS and EBM vertically and place two UPS stands with the extend

part at the end of the tower.

2. Tighten the screw on the metal

sheet for stabilization

3. Connect the Earth line from UPS

(port A ) to EBM (port B)

4. Take off the front panel, and connect the battery terminal (A) from UPS to EBM

terminal (B) shown as below. Users need to remove the small gate(C) on side of

the front panel to allow the outlet wire of the EBM to pass through the gate and

then reassemble front panel.

ENGLISH

III. Connecting the EBM in a rack form

1. Using the same method as assembling

UPS in a rack form, assemble EBM into

the rack-mounting on the top or

bottom of the UPS.

2. Connect the earth line from UPS (port

A ) to EBM (port B )

3. Take off the LCD box, and unscrew the

internal screws.

4. Take off the front panel, and connect

the battery terminal (A) from UPS to

EBM terminal (B) shown as below.

Users need to remove the small gate(C)

on side of the front panel to allow the

outlet wire of the EBM to pass through

the gate and then reassemble front

panel.

5. After installing the UPS into rack, the load can then be connected to UPS. Please

Unscrew

ENGLISH

make sure the load equipment is turned off before plugging all loads into the output

receptacle.

IV. Connecting the Multiple EBMs

1000VA/1500VA/2000VA and 3000VA UPS include external battery port that allows users

to connect multiple EBM in order to provide additional backup time. Follow the

procedure to install multiple EBM as below.

V. Connecting multiple EBMs in Tower form

1. Connect Earth line between UPS and the

first EBM, and then connect Earth Line

between the first EBM and the second

EBM.

2. Take off the front panel, and connect the

battery terminal (A) from UPS to EBM

terminal (B) shown as below. And then

connect the battery terminal (D) from the

first EBM to the battery terminal (E) from

the second EBM. Users need to remove

the small gate(C) on side of the front

panel to allow the outlet wire of the EBM

to pass through the gate and then

reassemble front panel.

VI. Connecting the Multiple EBMs in rack form

1. Connect Earth line between UPS and the first EBM, and then connect Earth Line between

the first EBM and the second EBM.

ENGLISH

2. Take off the front panel, and connect the battery terminal (A) from UPS to EBM terminal

(B) shown as below. And then connect the battery terminal (D) from the first EBM to the

battery terminal (E) from the second EBM. Users need to remove the small gate(C) on side

of the front panel to allow the outlet wire of the EBM to pass through the gate and then

reassemble front panel.

Note: Three or more EBMs can be connected to the UPS in the same way as shown above.

VII. Replacing UPS Internal Batteries

Follow the steps and Charts as below to replace batteries:

1. Take off the LCD box, and remove the

screws.

2. Slide and Pull the front panel leftward

and then take it off.

ENGLISH

3. Disconnect the cable from the UPS and

battery pack.

4. Remove the right inner battery bracket.

5. Pull the battery pack out onto flat area.

6. Install new battery pack into UPS.

7. Screw up the battery bracket and

reconnect the battery cable A and B

8. Re-install the front panel back to UPS.

Este manual sirve para los siguientes modelos

Otros manuales de Unión Postal Universal de PowerWalker

PowerWalker

PowerWalker VFI 1000R LCD Manual de usuario

PowerWalker

PowerWalker VI 500 R1U Manual de usuario

PowerWalker

PowerWalker VI 450 LCD Manual de usuario

PowerWalker

PowerWalker VFD 400 Manual de usuario

PowerWalker

PowerWalker VFI ICT IoT Series Manual de usuario

PowerWalker

PowerWalker VI 3000RT LCD Manual de usuario

PowerWalker

PowerWalker PowerWalker VFI 10000RT LCD Manual de usuario

PowerWalker

PowerWalker VFI 6000T LCD L Manual de usuario

PowerWalker

PowerWalker VFI 1000R/1U Manual de usuario

PowerWalker

PowerWalker VI CSW Series Manual de usuario

PowerWalker

PowerWalker VFI 1000 R1U Manual de usuario

PowerWalker

PowerWalker VFI 3000 LCD Guía de instalación

PowerWalker

PowerWalker VFI 10000 CG PF1 Manual de usuario

PowerWalker

PowerWalker VI 1000RT/LE Manual de usuario

PowerWalker

PowerWalker VI 400 Manual de usuario

PowerWalker

PowerWalker VFI 10000P/RT LCD Manual de usuario

PowerWalker

PowerWalker MBP 1-1 Manual de usuario

PowerWalker

PowerWalker VI 650 GX Manual de usuario

PowerWalker

PowerWalker VFI 10K CPH Manual de usuario

PowerWalker

PowerWalker DC UPS Manual de usuario

PowerWalker

PowerWalker VI 650SE LCD Manual de usuario

PowerWalker

PowerWalker VFI 1000 RMG PF1 Manual de usuario

PowerWalker

PowerWalker VI SCL Series Manual de usuario

PowerWalker

PowerWalker VFI 1000 C LCD Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario