Powerfix Profi 107555 Manual de usuario

IAN 107555

MULTI-FUNCTION DETECTOR PMDL 5 A1

MULTI-FUNCTION DETECTOR

Operating instructions

MULTIFUNKTIONSDETEKTOR

Betjeningsvejledning

MULTIDETEKTOR

Bruksanvisning

RAKENNEILMAISIN

Käyttöohje

MULTIFUNKTIONSDETEKTOR

Bedienungsanleitung

MULTIFUNCTIONELE

DETECTOR

Gebruiksaanwijzing

GB / IE Operating instructions Page 1

FI Käyttöohje Sivu 13

SE Bruksanvisning Sidan 25

DK Betjeningsvejledning Side 37

NL / BE Gebruiksaanwijzing Pagina 49

DE / AT / CH Bedienungsanleitung Seite 61

Before reading, unfold the page containing the illustrations and familiarise

yourself with all functions of the device.

Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen

kaikkiin toimintoihin.

Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och

gör dig bekant med apparatens/ maskinens funktioner.

Før du læser, vend siden med billeder frem og bliv bekendt med alle appara-

tets funktioner.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u ver-

trouwd met alle functies van het apparaat.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie

sich anschließend mit allen Funktionen des Gerätes vertraut.

- 1 -

CONTENT PAGE

Intended use 2

Safety instructions 2

Technical data 4

Description of the appliance 4

Items supplied 4

Unpacking 4

Inserting the battery 5

Measuring distances 5

Measuring areas 7

Measuring volumes 8

Locating concealed objects 8

Laser marking 10

Battery display 11

Cleaning and storage 11

Disposal 11

Warranty & Service 12

Importer 12

Read the operating instructions carefully before using the device for the first time and pre-

serve this booklet for later reference. Pass this manual on to whoever might acquire the devi-

ce at a future date.

- 2 -

MULTI-FUNCTION DETECTOR

PMDL 5 A1

Intended use

The Multi-Measurement Detector is designed for the locating of electrical cables,

of wood and metal objects, for the projecting of laser lines, for the measuring of

areas and volumes as well as for the measuring of distances. The appliance is

intended for domestic use only. Do not use it for commercial purposes. A different

or any other usage is regarded as unintended use and can lead to damages and

injuries. No liabity will be accepted for damage caused by manipulation of the

laser equipment, as well as of the ultrasound transmitter/receiver, or through

disregard of these safety instructions.

Safety instructions

Optimal and safe working with the multi-detector is only possible if you read these

operating and safety instructions completely and strictly follow their instructions.

Risk of injury!

• Do not use the appliance at locations where there is a risk of fire or

explosion, e.g. close to inflammable liquids or gases.

• This appliance may be used by children aged 8 over and by persons with

reduced physical, sensory or mental capabilities or lack of experience and

knowledge, provided that they are under supervision or have been told how

to use of the appliance safely and are aware of the potential risks. Children

must not play with the appliance. Cleaning and user maintenance tasks must

not be carried out by children unless they are supervised.

• Exercise caution with the holding pins. They are sharp and can cause injuries.

Caution regarding damage to the appliance!

• Do not expose the appliance to rainfall. Do not use the appliance in moist

or wet environments.

• Do not place objects containing liquids, e. g. flower vases, on the appliance.

• Do not place any open sources of fire, like candles, on the device.

- 3 -

This appliance contains a Class 2 laser. NEVER direct the laser beam at people

or animals. NEVER look directly into the laser. The laser can cause serious eye

damage.

• Do NOT direct the laser beam at strongly reflective material.

Reflected laser beams are also dangerous.

• Do NOT use the appliance to determine the alternating voltage level in

exposed or non-insulated power cables.

• Do NOT use the appliance as a substitute for a voltmeter.

Notes regarding inaccurate measurement results

The appliance does not always recognise all pipes and power cables.

The following conditions can contribute to inaccurate results:

– very thick walls

– weak battery

– deeply laid power cables or pipework

– shielded cables

– thick walls with thin pipes or power cables

– walls panelled with metal sheets

– very moist conditions

• This appliance is not suitable for detecting power cables in circuits,

– which are isolated from the mains power supply.

– through which direct current flows.

– which are used for computer or telecommunications systems.

• With this appliance pipework made of plastic or similar materials

cannot be detected, only pipework made of metal.

Interaction with batteries:

• Leaking batteries can cause damage to the appliance. If you do not intend

to use the appliance for an extended period, remove the batteries.

• Should the batteries leak, wear protective gloves and clean the battery

compartment with a dry cloth.

• Keep batteries away from children. Children can put batteries into their

mouths and swallow them. Should a battery ever be swallowed, seek

medical attention IMMEDIATELY.

- 4 -

Technical data

Distance measurement by means of Ultrasound

Locating of: power cables, metal, wood

Laser class: 2

Max. output power (P.max): <1 mW

Wave length (λ): 650 nm

according EN60825-1:2007

Power supply: 9 V block battery

Description of the appliance

1Measurement point

2Display

3Material switch (STUD/AC WIRE/METAL)

4Button – MODE

5Button – Holding pin

6Button – READ

7Button M (Memory)

8Spirit level

9Laser beam exit opening

0Ultrasound sender/receiver

qFunction switch (LASER/DETECTOR/DISTANCE)

wButton – RM (Read Memory)

eButton – Holding pin

rButton +/=

tBattery compartment

zButton – PUSH

Items supplied

• Multi-Function Detector

• 9V block battery

• Operating instructions

Unpacking

Take the Manifold Measurer from its packaging. Remove all transport restraints

and packaging materials. Remove the protective foil from the display 2.

- 5 -

Inserting the battery

1. Open the battery compartment ton the rear side of the Multi-Measurement

Detector.

2. Place the 9 V block battery onto the contacts. Pay heed to the correct polarity.

3. Lay the tape for removal of the battery underneath the 9V block battery and

press it into the battery compartment t.

Important!

Ensure that the wires are not trapped in any way.

This would lead to irreparable damage to the appliance.

4. Close the battery compartment t. The battery compartment lid must close

with an audible click.

Measuring distances

1. Slide the function switch qto „DISTANCE“. The display 2switches itself on.

To switch between the metric and the Anglo-American units of measurement,

press and hold the button MODE 4. Then press the button READ 6and release

both buttons simultaneously. When you release the buttons, the measurement

units change.

Note:

Measurements start at the measurement point 1!

Should the measurement lie outside the measurement range, „Err“ or an illogical

number appear in the display. The measurement range lies between 0,6m (2’)

and 16 m (53’).

2. Hold the appliance upright towards the wall to which you wish to measure

the distance. The ultrasound sender/receiver 0must be at a right-angle to

the wall. For this, use the spirit level: The bubble in the glass 8must stand

between the marking lines (see Fig.1).

3. Press the button READ 6. The distance measured appears in the display 2.

When you hold the button READ 6pressed down and slowly move the

appliance over the surface to be measured, the appliance continually

measures the distances. These are shown on the display 2.

- 6 -

Take note of the following illustrations:

Fig.1 Fig. 2

The further you are from the wall, the wider is the area (a) that the Multi-

Measurement Detector must measure by ultrasound (Fig. 2). Therefore take care

that the Manifold Measurer is always directed at a right angle towards a level

surface (Fig. 1 and 3). Ensure that there are no objects positioned within the

measurement area.

False!

(Fig. 3)

The display illumination glows during the measurement. If a button is not pressed

within ca.15 seconds, the illumination extinguishes. After a further ca.15 seconds

the diplay itself switches off. Press the button READ 6, to reactivate the display and

the illumination.

Note:

Inaccurate measurements can also occur through a weak battery.

If the battery is too weak, the battery symbol appears in the display.

- 7 -

Adding distances together

You can add the measured distances together:

1. Measure the first distance as described.

2. Press the button +/= r. In the display 2, „+“ appears and the distance

measured carries itself over to the lower line.

3. Measure the next distance. The newly measured distance is shown in the

upper line.

4. Once again, press the button +/= r. The new measurement is added

to the old measurement in the lower line.

5. Repeat steps 2 to 4 to add further measurements.

6. When you wish to leave the addition mode, press the button MODE 4.

All values are erased.

Measuring areas

1. Slide the function switch qto „DISTANCE“.

The display 2switches itself on.

2. Press the button MODE 4once. In the display 2flashes „L“ (Length).

3. Press the button READ 6, to measure the length. In the upper line

the measured length appears and „W“ (Width) starts to flash.

4. Press the button READ 6to measure the width. The measured width

appears on the upper line and the result of the area calculation in the

lower line.

Adding areas together

1. Measure an area as described in the section „Measuring areas“.

2. Press the button M 7. „M+“ appears in the display 2.

The area measured is now saved.

3. Press the button MODE 4. The appliance is now ready for the second

measurement.

4. Measure the next area.

5. Press the button +/= r. A „+“ appears in the display 2.

6. Press the button RM w. The result of the first measurement is shown in the

lower line.

7. Press the button +/= r. Both measurements are added together and

the result is shown in the lower line.

8. Repeat the steps 2 to 7 to add in further measurement values.

9. When you wish to leave the addition mode, press the button MODE 4.

All values are erased.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Sensor de seguridad de Powerfix Profi

Powerfix Profi

Powerfix Profi Z31385 Manual de usuario

Powerfix Profi

Powerfix Profi KH 2927-2 Manual de usuario

Powerfix Profi

Powerfix Profi KHH 2927-2 Manual de usuario

Powerfix Profi

Powerfix Profi Z31385 Manual de usuario

Powerfix Profi

Powerfix Profi 285131 Manual de usuario

Powerfix Profi

Powerfix Profi Z31712A/C Manual de usuario

Powerfix Profi

Powerfix Profi 298736 Manual de usuario

Powerfix Profi

Powerfix Profi 91252 Manual de usuario

Powerfix Profi

Powerfix Profi 288019 Manual de usuario

Powerfix Profi

Powerfix Profi 278296 Manual de usuario

Powerfix Profi

Powerfix Profi PMDL 5 B1 Manual de usuario

Powerfix Profi

Powerfix Profi KH 2927-2 Manual de usuario

Powerfix Profi

Powerfix Profi 40111 Manual de usuario

Powerfix Profi

Powerfix Profi 288019 Manual de usuario

Powerfix Profi

Powerfix Profi PMDL 5 B1 Manual de usuario

Powerfix Profi

Powerfix Profi 271367 Manual de usuario

Powerfix Profi

Powerfix Profi 273599 Manual de usuario

Powerfix Profi

Powerfix Profi 288019 Manual de usuario

Powerfix Profi

Powerfix Profi 278296 Manual de usuario

Powerfix Profi

Powerfix Profi 288019 Manual de usuario

Powerfix Profi

Powerfix Profi 77287 Manual de usuario

Powerfix Profi

Powerfix Profi HG00384B Manual de usuario

Powerfix Profi

Powerfix Profi 97003 Manual de usuario

Powerfix Profi

Powerfix Profi PMDL 5 A1 Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario