Power Fist 8957425 Manual de usuario

V4.0 8957425

Pleaseread and understand allinstructionsbeforeuse.Retain this manualfor

futurereference.

User Manual

120V 1,000 BPM Demolition

Hammer Kit

8957425 120V1,000 BPM Demolition Hammer Kit V4.0

2 For technical questions call1-800-665-8685

SPECIFICATIONS

Motor 120V,60Hz,15A

Chuck Hex

Impact Rate 1000 BPM

ToolHolder

1-1/8 in.Hex

Impact Energy

62J

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personalinjury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

IMPORTANT SAFETY INFORMATION

•Read and understand all instructions. Failure to follow all instructions may

result in serious injury or property damage.

•The warnings, cautions, and instructions in this manual cannot cover all

possible conditions or situations that could occur. Exercise common sense

and caution when using this tool. Always be aware of the environment and

ensure that the tool is used in a safe and responsible manner.

•Do not allow persons to operate or assemble the product until they have

read this manual and have developed a thorough understanding of how it

works.

•Do not modify this product in any way. Unauthorized modification may

impair the function and/or safety and could affect the life of the product.

120V 1,000 BPM Demolition

Hammer Kit

V4.0 120V1,000 BPM Demolition Hammer Kit 8957425

Visitwww.princessauto.comfor more information 3

There are specific applications for which the product was designed.

•Use the right tool for the job. DO NOT attempt to force small equipment to

do the work of larger industrial equipment. There are certain applications

for which this equipment was designed. This product will be safer and do a

better job at the capacity for which it was intended. DO NOT use this

equipment for a purpose for which it was not intended.

•Industrial or commercial applications must follow OSHA requirements.

WORK AREA SAFETY

•Inspect the work area before each use. Keep work area clean, dry, free of

clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury.

Using the product in confined work areas may put you dangerously close to

cutting tools and rotating parts.

•Do not use the product where there is a risk of causing a fire or an

explosion; e.g., in the presence of flammable liquids, gases, or dust. The

product can create sparks, which may ignite the flammable liquids, gases,

or dust.

•Do not allow the hammer to come into contact with an electrical source.

The tool is not insulated and contact will cause electrical shock.

•Keep children and bystanders away from the work area while operating the

tool. Do not allow children to handle the product.

•Be aware of all power lines, electrical circuits, water pipes, and other

mechanical hazards in your work area. Some of these hazards may be

hidden from your view and may cause personal injury and/or property

damage if contacted.

PERSONAL SAFETY

•Stay alert, watch what you are doing, and use common sense when

operating the tool. Do not use the tool while you are tired or under the

influence of drugs, alcohol, or medication. A moment of inattention while

operating the tool may result in serious personal injury.

•Dress properly. Do not wear loose clothing, dangling objects, or jewelry.

Keep your hair, clothing and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts. Air vents on the tool

8957425 120V1,000 BPM Demolition Hammer Kit V4.0

4 For technical questions call1-800-665-8685

often cover moving parts and should be avoided.

•Wear the proper personal protective equipment when necessary. Use ANSI

Z87.1 compliant safety goggles (not safety glasses) with side shields, or

when needed, a face shield. Use a dust mask in dusty work conditions. Also

use non-skid safety shoes, hardhat, gloves, dust collection systems, and

hearing protection when appropriate. This applies to all persons in the work

area.

•Do not overreach. Keep proper footing and balance at all times.

•Remove keys or wrenches before connecting the tool to an air supply,

power supply, or turning on the tool. A wrench or key that is left attached to

a rotating part of the tool may cause personal injury.

•Secure the work with clamps or a vise instead of your hand when practical.

This safety precaution allows for proper tool operation using both hands.

HEX BREAKER HAMMERUSE AND CARE

•Do not force the demolition hammer. Products are safer and do a better job

when used in the manner for which they are designed. Plan your work, and

use the correct product for the job.

•Check for damaged parts before each use. Carefully check that the product

will operate properly and perform its intended function. Replace damaged

or worn parts immediately. Never operate the product with a damaged part.

•Do not use a product with a malfunctioning switch. Any power tool that

cannot be controlled with the power switch is dangerous and must be

repaired by an authorized service representative before using.

•Disconnect the power/air supply from the product and place the switch in

the locked or off position before making any adjustments, changing

accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally.

•Store the hammer when it is not in use. Store it in a dry, secure place out of

the reach of children. Inspect the tool for good working condition prior to

storage and before re-use.

•Use only accessories that are recommended by the manufacturer for use

with your product. Accessories that may be suitable for one product may

V4.0 120V1,000 BPM Demolition Hammer Kit 8957425

Visitwww.princessauto.comfor more information 5

create a risk of injury when used with another tool. Never use an accessory

that has a lower operating speed or operating pressure than the tool itself.

•Keep guards in place and in working order. Never operate the product

without the guards in place.

•Do not leave the demolition hammer running unattended.

SPECIFIC OPERATION WARNINGS

•To reduce the risk of injury always wear eye protection

•Wear ear protection when using the hammer. Exposure to noise can cause

hearing loss.

•Wear heavy duty anti vibration gloves.

•Be sure the bit is secured in place before operation.

•Hold power tools by insulated gripping surfaces, when performing an

operation where the cutting tool may contact hidden wiring or its own cord.

•When drilling or screwing into walls, ceilings, etc., make sure beforehand

that you will not damage any hidden electric cables. During this work you

should not touch any metal parts of the machine; only touch the machine by

the plastic housing.

•Always be sure you have a firm footing.

•Hold the hammer firmly with both hands.

•Be sure no one is below you when using the hammer in high locations.

•Do not point the hammer at anyone in the area when operating. The bit

could fly out and seriously injure someone.

•Burn hazard. Do not touch the bit or parts close to the bit immediately after

operation; they will be extremely hot.

GROUNDING

•This machine must be grounded while in use to protect the operator from

electrical shock. This unit is equipped with an electrical cord that has an

equipment grounding conductor and a grounding plug. The plug MUST be

plugged into a matching receptacle that is properly installed and grounded

in accordance with ALL local codes and ordinances.

8957425 120V1,000 BPM Demolition Hammer Kit V4.0

6 For technical questions call1-800-665-8685

•Do not modify the provided plug. If it will not fit the receptacle, have the

proper receptacle installed by a qualified electrician.

•Check with a qualified electrician or service person if you do not completely

understand the grounding instructions, or if you are not sure the tool is

properly grounded.

GROUNDED TOOLS: TOOLS WITH 3-PRONG PLUGS

•Tools marked with Grounding

Required have a 3-wire cord and 3-

prong grounding plug. The plug

must be connected to a properly

grounded outlet. If the tool should

electrically malfunction or break

down, grounding provides a low

resistance path to carry electricity

away from the user, reducing the

risk of electric shock. (See Figure

A.)

•The grounding prong in the plug is connected through the green wire inside

the cord to the grounding system in the tool. The green wire in the cord

must be the only wire connected to the tool’s grounding system and must

never be attached to an electrically live terminal.

•Your tool must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet

should look like those in the following illustration.

DOUBLE INSULATED TOOLS:

TOOLS WITH TWO-PRONG PLUGS

•Tools marked Double Insulated do not

require grounding. They have a special

double insulation system which

satisfies OSHA requirements and

complies with the applicable standards

of Underwriters Laboratories, Inc., the

Canadian Standard Association, and

V4.0 120V1,000 BPM Demolition Hammer Kit 8957425

Visitwww.princessauto.comfor more information 7

the National Electrical Code. (See Figure B.)

•Double insulated tools may be used in either of the 120 volt outlets shown

in the following illustration.

EXTENSIONCORDS

•Use a proper extension cord. Make sure your extension cord is in good

condition. When using an extension cord, be sure to use one heavy enough

to carry the current your product will draw. An undersized cord will cause a

drop in line voltage, resulting in loss of power and cause overheating.

•Be sure your extension cord is properly wired and in good condition.

Always replace a damaged extension cord or have it repaired by a qualified

person before using it. Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

•Grounded tools require a 3-wire extension cord. Double Insulated tools can

use either a 2- or 3-wire extension cord.

•As the distance from the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with inadequately sized wire

causes a serious drop in voltage, resulting in loss of power and possible

tool damage.

•The smaller the wire’s gauge number, the greater the capacity of the cord.

For example, a 14-gauge cord can carry a higher current than a 16-gauge

cord. Minimum extension cord wire size is shown in the following table:

MINIMUM WIRE SIZE OF EXTENSIONCORDS

NameplateAMPS

Cord Length

25' 50' 100' 150'

0-6 18 AWG 16 AWG 16 AWG 14 AWG

6-10 18 AWG 16 AWG 14 AWG 12 AWG

10-12

16 AWG

14 AWG

12 AWG

12-16

14 AWG

12 AWG

Not Recommended

•When using more than one extension cord to make up the total length,

make sure each cord contains at least the minimum wire size required.

•If you are using one extension cord for more than one tool, add the

nameplate amperes and use the sum to determine the required minimum

8957425 120V1,000 BPM Demolition Hammer Kit V4.0

8 For technical questions call1-800-665-8685

cord size.

•If you are using an extension cord outdoors, make sure it is marked with

the suffix Wto indicate it is acceptable for outdoor use.

•Make sure your extension cord is properly wired and in good electrical

condition. Always replace a damaged extension cord or have it repaired by a

qualified electrician before using it.

•Protect your extension cords from sharp objects, excessive heat, and damp

or wet areas.

IDENTIFICATIONKEY

A. Main Handle

B. Switch

C. Fan Cover

D. Side Handle

E. Chisel Chuck

F. Front Cover

G. Aluminum Head

ASSEMBLY INSTRUCTIONS

WARNING! Make sure that the trigger is in the OFF position and unplug the

demolition hammer from its electrical outlet before performing any

procedure in this section.

CAUTION! The inserted tool may become hot during use. There is a risk of

burning your hands. Wear protective gloves when inserting or removingthe

tool from the holder.

V4.0 120V1,000 BPM Demolition Hammer Kit 8957425

Visitwww.princessauto.comfor more information 9

MOUNTING TOOL BITS

CAUTION! Before any work on the machine itself, pull the mainplug. Before

each use, clean the bit’s shank and lubricate.

BITS WITH GROOVES

1. Move the lock (2) to Fig 1

position. Insert the bit (1)

into the holder (3).

2. Move the lock back. Pull the

bit to check if it was locked.

3. When disassembling, move

the lock to Fig 1 position,

then pull out the bit from the

holder.

BITS WITH SHOULDER

IMPORTANT! The shank length

can be 160 mm or 6 10/33 inch (Length from shank end to the shoulder)

1. Move the lock (2) to Fig 3 position. Insert the bit (1) into the holder (3).

2. Move the lock to Fig 4 position. Bit can be locked. The shoulder position

should be between lock and holder.

3. Move the lock back. Pull the bit to check if it was locked.

4. When disassembling, move the lock to Fig 3 position, then pull out the bit

from the holder.

WARNING!

•Be sure the bit is secured in place before operation.

•When drilling or screwing into walls, ceilings, etc., make sure beforehand

that you will not damage any hidden electric cables. During this work, you

should not touch any metal parts of the machine; only touch the machine by

the plastic housing.

•Be sure no one is below you when using the tool in high locations.

•Always remove the plug from the power source before installing or

removing a bit or accessory from the chuck.

8957425 120V1,000 BPM Demolition Hammer Kit V4.0

10 For technical questions call1-800-665-8685

OPERATINGINSTRUCTIONS

WARNING!

•To reduce the risk of injury, always wear eye protection.

•Wear ear protection when using the hammer. Exposure to noise can cause

hearing loss.

•Wear heavy duty anti vibration gloves.

•Be sure the bit is secured in place before operation.

•Hold power tools by insulated gripping surfaces, when performing an

operation where the cutting tool may contact hidden wiring or its own cord.

•Always be sure you have a firm footing.

•Hold the tool firmly with both hands.

•Do not point the hammer at anyone in the area when operating. The bit

could fly out and seriously injure someone.

•Burn hazard. Do not touch the bit or parts close to the bit immediately after

operation; they will be extremely

•Use only well-sharpened bits that are in good condition and appropriate to

task.

•To prevent the bit from jamming, keep the motor running when pulling the

bit out of a completed hole.

POWER SOURCE

Ensure that the power source to be utilized conforms to the power

requirements, which are specified on the nameplate of the hammer.

POWER SWITCH

Ensure that the power switch is in the OFF position. If the plug is connected to a

power receptacle while the power switch is in ON position, the demolition

hammer will start operation immediately, which could cause a serious accident!

EXTENSION CORD

When the work area is removed from the power source, use an extension cord

of sufficient thickness and rated capacity. The extension cord should be kept as

Tabla de contenidos

Idiomas:

Otros manuales de Herramientas de Power Fist

Power Fist

Power Fist 8502494 Manual de usuario

Power Fist

Power Fist 8823494 Manual de usuario

Power Fist

Power Fist 8662330 Manual de usuario

Power Fist

Power Fist 8887408 Manual de usuario

Power Fist

Power Fist 8074668 Manual de usuario

Power Fist

Power Fist Air Hammer Manual de usuario

Power Fist

Power Fist 8663783 Manual de usuario

Power Fist

Power Fist 9151051 Manual de usuario

Power Fist

Power Fist 8438806 Manual de usuario

Power Fist

Power Fist 8880940 Manual de usuario

Power Fist

Power Fist 8665549 Manual de usuario

Power Fist

Power Fist 8308231 Manual de usuario

Power Fist

Power Fist 8505547 Manual de usuario

Power Fist

Power Fist 8843583 Manual de usuario

Power Fist

Power Fist 1/2 in. Air Ratchet and Socket Set Manual de usuario

Power Fist

Power Fist 8916793 Manual de usuario

Power Fist

Power Fist 8873358 Manual de usuario

Power Fist

Power Fist 8885642 Manual de usuario

Power Fist

Power Fist 9004391 Manual de usuario

Power Fist

Power Fist Air Line Delivery Kit Manual de usuario

Power Fist

Power Fist 8655888 Manual de usuario

Power Fist

Power Fist 8063927 Manual de usuario

Power Fist

Power Fist 8536773 Manual de usuario

Power Fist

Power Fist 8685042 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar