Potterton Osprey 2 CFL 125 Instrucciones de operación

Osprey 2 CFL

125 - 150 - 180 - 220

Gas Fired Floor Standing Boiler

Users Operating

Instructions

Please leave these instructions with the user

Natural Gas

Potterton Osprey 2 CFL 125

G.C.No41 590 54

Potterton Osprey 2 CFL 150

G.C.No41 590 55

Potterton Osprey 2 CFL 180

G.C.No41 590 56

Potterton Osprey 2 CFL 220

G.C.No41 590 57

The boiler meets the requirements of Statutory

Instrument “ The Boiler (Efficiency) Regulations

1993 No3083” and is deemed to meet the

requirements of Directive 92/42/EEC on the energy

efficiency requirements for new hot water boilers

fired with liquid or gaseous fuels:-

Type test for purpose of Regulation 5 certified by:

Notified Body 0049.

Product/Production certified by:

Notified Body 0049.

For GB/IE only.

Guarantee

Your Potterton Osprey 2 CFL is

designed and produced to meet all

the relevant Standards.

Potterton provide a 12 month

guarantee on the boiler. The

guarantee operates from the date

installation is completed for the

customer who is the original user.

To maximise the benefit from our

guarantee we urge you to return the

reply-paid guarantee registration.

This does not in any way prejudice

your rights at Common Law. Such

rights between the customer and the

installer or supplier from whom the

unit was purchased remain intact.

Any component or part which

becomes defective during the

guarantee period as a result of faulty

workmanship or material whilst in

normal use will be repaired or

replaced free of charge.

1.0 Warnings

1.1 Safe Installation

1. The appliance is suitable for installation only in

G.B. and I.E. and should be installed in

accordance with the rules in force. For Ireland

install in accordance with I.S.813 “INSTALLATION

OF GAS APPLIANCES”. The installation must be

carried out by a CORGI Registered Installer or

other registered competent person and be in

accordance with the relevant requirements of

current GAS SAFETY (Installation and Use)

REGULATIONS most recent edition, the BUILDING

REGULATIONS issued by the Department of the

Environment, BUILDING STANDARDS (Scotland)

(Consolidation) REGULATIONS issued by the

Scottish Development Department and the LOCAL

BUILDING REGULATIONS.Where no specific

instructions are given, reference should be made

to the relevant BRITISH STANDARD CODES OF

PRACTICE and INSTALLATION

SPECIFICATIONS.

2. This appliance must be installed in

accordance with the manufacturer’s instructions

and the rules in force, and only used in a suitably

ventilated location.

3. Read the instructions before installing or

using this appliance.

4. Any purpose provided ventilation (see Section

3.0) should be checked periodically to ensure that

it is free from obstruction.

IMPORTANT - The addition of anything that

may interfere with the normal operation of the

appliance without the express written

permission of Potterton could invalidate the

appliance warranty and infringe the GAS

SAFETY (Installation and Use) REGULATIONS.

1.2 In case of gas leaks

1. If a gas leak is found or suspected, turn off the

gas supply at the meter immediately and contact

your Installer or Transco (under ‘Gas’in the ‘phone

directory).

1.3 Servicing your Appliance

1. For reasons of safety and economy your

appliance should be serviced annually. Servicing

must be performed by a competent person. Your

Installer or British Gas Service will be able to advise

you.

1.4 Electricity Supply

1. THIS APPLIANCE MUST BE EARTHED.

2. A standard 230V ~ 50Hzsupply is required. The

appliance must be protected by a 3 amp fuse.

STANDARD

B.S. 6891

B.S. 5440: Pt 1

B.S. 5440: Pt 2

B.S. 5546

B.S. 7074

B.S. 5449

B.S. 6798

SCOPE

Gas Installation.

Flues.

Ventilation.

Installation of hot water supplies

for domestic purposes.

Expansion vessels and ancillary

equipment for sealed water systems.

Forced circulation hot water systems.

Installation of gas fired boilers.

“Benchmark”Installation, Commissioning and Service Record

Log Book

Please ensure that your installer has completed the Installation and

Commissioning sections of the Log Book and hands the Log Book over.

The details of the Log Book will be required in the event of any warranty

work. Keep the Log Book in a safe place and ensure that the relevant

sections are completed at each subsequent regular service visit.

All CORGI registered installers carry a CORGI identification card and have

a registration number. Both should be recorded in your boiler Log Book.

You can check your installer is registered by telephoning 01256 372300 or

writing to:-

1 Elmwood,

Chineham Business Park,

Crockford Lane,

Basingstoke

RG24 8WG

Never Hang Flammable Items Over The

Appliance

2.0 Operating the Boiler

2.1 Introduction

1. Your Potterton Osprey 2 CFL is a gas fired,

open flue, floor standing boiler. The boiler can be

used to supply hot water for central heating, and

domestic hot water when used in conjunction with

an indirect cylinder.

2. The boiler is designed for use on fully pumped

open vented or sealed systems. It can be used on

Natural Gas (G20) only.

3. Instructions for use can also be found behind

the boiler front panel (Fig. 1).

2.2 Operating the Boiler

1. Ensure that the gas and electricity supplies are

turned on and that all timers, thermostats etc. are

calling for heat.

2. The Power On neon should be illuminated.

3. Push the On/Off button in. The button will

illuminate and the ignition sequence will start.

4. The pilot flame will light followed by the main

burner. This is indicated by the Burner On neon

illuminating.

5. The optimum setting of the boiler temperature

control depends upon type of system, external

controls and your requirements. Your Installer will

be able to advise you on this matter.

2.3 Flame Failure

1. If at any time the burner is extinguished while

there is still a demand for the boiler to operate the

Flame Failure neon will illuminate. The Burner On

neon will extinguish.

2. Pressing the Flame Failure reset button will

restart the ignition sequence.

3. If the Flame Failure neon illuminates repeatedly

a fault is indicated. Your Service Engineer should

be contacted as soon as possible.

2.4 Boiler Safety Overheat Thermostat

1. The boiler is fitted with an additional safety

device, which shuts down the boiler in the event of

the system or the boiler overheating.

2. If the device operates, the Boiler Safety

Overheat neon will illuminate and the boiler will

shut down.

3. Unscrew the cap off the Boiler Safety Overheat

Reset. Press the reset button to restart the ignition

sequence.

4. If the Boiler Safety Overheat neon illuminates

repeatedly a fault is indicated. Your Service

Engineer should be contacted as soon as

possible.

RESET ON / OFF

Osprey 2 RESET

Fig. 2

Fig. 1

Control Panel

Boiler Safety

Overheat Neon

Boiler Safety

Overheat Reset

Temperature

Control

Burner On

Neon

Flame Failure

Neon

Flame Failure

Reset Button

On/Off

Button

Power On

Neon

Front Panel

2.0 Operating the Boiler

2.5 Flue Safety Thermostat

1. The boiler is fitted with a safety thermostat in

the flue draught diverter.

2. If the flue becomes blocked or is subjected to

adverse conditions the safety thermostat will

operate and shut down the boiler. The Burner On

neon will extinguish.

Note: The Flame Failure neon and Boiler

Safety Overheat neon will not illuminate if

the Flue Safety Thermostat is activated.

After approximately 10 minutes the boiler

will relight if there is still a demand for heat.

3. If the blockage or adverse condition persists the

safety thermostat will continue to operate and

cycle the boiler on and off. As a result the boiler

may not be able to supply adequate hot water for

heating and/or domestic purposes.

4. Under normal circumstances the boiler will cycle

on and off as dictated by the Temperature Control

Thermostat. If the cycling appears to be excessive

with long periods where the boiler is off and the

heating/hot water performance is diminished turn

the boiler off and contact your Service Engineer as

soon as possible.

2.6 To Shut Off the Boiler

1. For short periods: Press the On/Off Button so

that it is not illuminated.

2. For longer periods: Turn off the electricity and

gas supplies.

If your home is to be left unoccupied for long

periods during cold weather the boiler and

whole system should be drained unless there is

additional frost protection.

3. Your Installer will advise you about frost

protection and draining the system.

3.0 Clearances & Ventilation

IMPORTANT - If the boiler is not already in a

compartment and you wish to enclose it

consult your installer before commencing any

work. Specific details of compartments and

their ventilation are included in the Installation

Instructions, and reference made to the

relevant British Standards.

3.1 Clearances around the Boiler

(Figs. 3 & 4)

1. The minimum clear spaces needed around

the boiler measured from the casing are as

follows:-

Top - 700mm

Sides - 150mm

Front - 700mm

Rear - 200mm

2. These areas must not be obstructed in any

way. Blocking the clearance spaces may

result in the boiler overheating and damage

may occur. The ventilation will also be

affected (see below).

3. Any combustible material must be at least

25mm from the flue pipe at any point along the

length of the pipe.

4. Any compartment should be large enough to

house the boiler and ancillary equipment only

providing that the minimum clearances are

adhered to.

IT SHOULD NOT BE USED AS A STORAGE

CUPBOARD.

3.2 Ventilation

1. The Osprey 2 CFL is an open flue appliance

that takes air for combustion from the room or

compartment in which it is installed (Note: Only

125 & 150 models can be fitted in

conventional compartments. 180 & 220

models have special requirements).

2. The room or compartment will incorporate air

vents which must not be blocked or obstructed in

any way. If these vents do not communicate

directly with outside there will be further vents in

adjoining rooms. These vents must also not be

blocked or obstructed.

3. Details of ventilation requirements are given in

the Installation and Servicing Instructions.

4. If any building work or alterations are carried

out that may affect the ventilation consult your

Installer who will advise if further vents are

required.

700mm

150mm

Minimum Side

Clearances

Minimum Front &

Rear Clearances

Fig. 3

Fig. 4

200mm

4.1 Check List

1. If a fault develops, or is suspected, call your

Service Engineer as soon as possible.

2. Go through the following check list before you

make contact.

a) Are the gas and electricity supplies on ?

b) Is the On/Off button in the on position ?

c) Is the Flame Failure neon illuminated ?

If so, press the Reset Button.

d) Is the Boiler Safety Overheat Neon

illuminated ?

If so, remove the cover and press the Boiler

Safety Overheat Reset.

e) Is the boiler temperature control set high

enough ?

f) Are the time clock and room thermostat

(where fitted) calling for heat ?

g) Are all the radiator valves open ?

4.2 Cleaning the Outercase

The painted panels should be wiped with a damp

cloth and then dried completely. DO NOT USE

ABRASIVE CLEANING AGENTS.

4.3 Spare Parts

IMPORTANT - Only a competent person should

be used to service or repair this boiler

1. Any repairs to the boiler will usually be the

responsibility of the installer during the guarantee

period after which spare parts may be obtained

through approved Potterton stockists if required.

2. Quote the appliance name, model number and

where possible the part number when ordering

spares. The appliance data badge is situated as

shown in Fig. 5. A short parts list is included in

the Installation and Servicing Instructions.

4.0 Check List, Cleaning, Spares

& Guarantee

Inner Front

Panel

Data Badge

Fig. 5

Potterton, Baxi UK Limited, Brownedge Road, Bamber Bridge, Preston, Lancashire. PR5 6SN

After Sales Service 08706 096 096 Technical Enquiries 08706 049 049

www.baxi.com

Comp. No. 5106753 - Iss 1 - 01/02

PO890C0

Tabla de contenidos

Otros manuales de Caldera de Potterton

Potterton

Potterton Promax System HE Plus A Range Manual de instrucciones

Potterton

Potterton Cold HE A Manual de usuario

Potterton

Potterton Promax 24 Combi ErP Manual

Potterton

Potterton Osprey CF 180 Instrucciones de instalación y mantenimiento

Potterton

Potterton PROMAX 12 Manual de usuario

Potterton

Potterton Paramount two 60 Manual de usuario

Potterton

Potterton PROMAX SL 12 Manual de usuario

Potterton

Potterton Prorile Prima 30e Guía del usuario

Potterton

Potterton Performa 30 HE Instrucciones de instalación y mantenimiento

Potterton

Potterton Performa 30 HE Manual de usuario

Potterton

Potterton PRIMA 30C Manual de usuario

Potterton

Potterton Performa 24 Eco HE Instrucciones de instalación y mantenimiento

Potterton

Potterton Prorile Prima 30e Guía del usuario

Potterton

Potterton Performa 24 Instrucciones de operación

Potterton

Potterton Prorile Prima 30e Guía del usuario

Potterton

Potterton Gas condensing boiler Manual de usuario

Potterton

Potterton Promax System HE Plus A Range Instrucciones de instalación y mantenimiento

Potterton

Potterton SIRIUS FS 50-70 Manual de usuario

Potterton

Potterton Gold 24 HE Instrucciones de instalación y mantenimiento

Potterton

Potterton Gold Combi 24 Manual de usuario

Potterton

Potterton Eurocondense five 125 kW Manual de usuario

Potterton

Potterton Performa System 28e Instrucciones de operación

Potterton

Potterton Gold H Range Manual de instrucciones

Potterton

Potterton Promax SL series Instrucciones de instalación y mantenimiento

Manuales populares de Caldera de otras marcas

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manual de usuario

Radijator

Radijator BIO max 23.1 Manual de usuario

Brunner

Brunner BSV 20 Manual de usuario

Buderus

Buderus Logamax GB062-24 KDE H V2 Manual de usuario

UTICA BOILERS

UTICA BOILERS TriFire Manual de usuario

Joannes

Joannes LADY Series Manual

ECR International

ECR International UB90-125 Manual de instrucciones

Froling

Froling FHG Turbo 3000 Manual de usuario

Froling

Froling P4 Pellet 8 - 105 Manual de usuario

U.S. Boiler Company

U.S. Boiler Company K2 Manual de usuario

Henrad

Henrad C95 FF Manual de usuario

NeOvo

NeOvo EcoNox EF 36 Manual de usuario

Eco Hometec

Eco Hometec EC 25 COMPACT Manual de usuario

Viessmann

Viessmann VITODENS 200 Guía

Baxi

Baxi Prime 1.24 Manual de usuario

REXNOVA

REXNOVA ISA 20 BITHERMAL Manual de usuario

Radiant

Radiant R2K 55 Manual

Worcester

Worcester Greenstar 36LXi Manual de usuario