Potterton Performa 24 Instrucciones de operación

Performa 24

Gas Fired Wall Mounted Combination Boiler

User’s Operating

Instructions

Please keep these instructions safe.

Should you move house, please hand

them over to the next occupier.

Natural Gas

Potterton Performa 24

G.C.No47 393 06

The boiler meets the requirements of Statutory

Instrument “ The Boiler (Efficiency) Regulations

1993 No3083” and is deemed to meet the

requirements of Directive 92/42/EEC on the energy

efficiency requirements for new hot water boilers

fired with liquid or gaseous fuels:-

Type test for purpose of Regulation 5 certified by:

Notified Body 0051.

Product/Production certified by:

Notified Body 0051.

For GB/IE only.

Where fitted, user label for

optional timer to be applied here.

Guarantee

Your Potterton Performa 24 is

designed and produced to meet all

the relevant Standards.

Potterton provide a 12 month

guarantee on the boiler. The

guarantee operates from the date

installation is completed for the

customer who is the original user.

To maximise the benefit from our

guarantee we urge you to return the

reply-paid guarantee registration.

This does not in any way prejudice

your rights at Common Law. Such

rights between the customer and the

installer or supplier from whom the

unit was purchased remain intact.

Any component or part which

becomes defective during the

guarantee period as a result of faulty

workmanship or material whilst in

normal use will be repaired or

replaced free of charge.

STANDARD

B.S. 6891

B.S. 5440: Pt 1

B.S. 5440: Pt 2

B.S. 5546

B.S. 7074

B.S. 5449

B.S. 6798

SCOPE

Gas Installation.

Flues.

Air Supply.

Installation of hot water supplies

for domestic purposes.

Expansion vessels and ancillary

equipment for sealed water systems.

Forced circulation hot water systems.

Installation of gas fired hot water

boilers.

1.0 Warnings

1.1 Safe Installation

1. The appliance is suitable for installation only in

G.B. and I.E. and should be installed in

accordance with the rules in force. For Ireland

install in accordance with I.S.813 “INSTALLATION

OF GAS APPLIANCES”. The installation must be

carried out by a CORGI Registered Installer or

other registered competent person and be in

accordance with the relevant requirements of GAS

SAFETY (Installation and Use) REGULATIONS most

recent edition, the BUILDING REGULATIONS issued

by the Department of the Environment, BUILDING

STANDARDS (Scotland) (Consolidation)

REGULATIONS issued by the Scottish Development

Department and the LOCAL BUILDING

REGULATIONS.Where no specific instructions are

given, reference should be made to the relevant

BRITISH STANDARD CODES OF PRACTICE

and INSTALLATION SPECIFICATIONS.

2. This appliance must be installed in

accordance with the manufacturer’s instructions

and the rules in force, and only used in a suitably

ventilated location.

3. Read the instructions before installing or

using this appliance.

4. Any purpose provided ventilation should be

checked periodically to ensure that it is free from

obstruction.

IMPORTANT - The addition of anything that

may interfere with the normal operation of the

appliance without express written permission

could invalidate the appliance warranty and

infringe the GAS SAFETY (Installation and Use)

REGULATIONS.

1.2 In case of gas leaks

1. If a gas leak is found or suspected, turn off the

gas supply at the meter immediately and at the

isolating valve on the boiler if possible. Contact your

Installer or Transco (under 'Gas' in the phone

directory).

1.3 Servicing your Appliance

1. For reasons of safety and economy your

appliance should be serviced annually. Servicing

must be performed by a competent person. Your

Installer or British Gas Service will be able to advise

you.

1.4 Electricity Supply

1. THIS APPLIANCE MUST BE EARTHED.

2. A standard 230V ~ 50Hzsupply is required. The

appliance must be protected by a 3 amp fuse.

Never Hang Flammable Items Over The

Appliance

IN AN EMERGENCY

If a water or gas leak occurs or is suspected, the boiler can be

isolated at the inlet valves as follows;

1. Turn off the electrical supply and turn the selector switch on

the facia to the OFF position.

2. Using a suitable open ended spanner or screwdriver turn the

square on the gas tap to the left to isolate the gas supply at the

boiler (Fig. 1).

3. The water isolating valves are positioned under the boiler and

can be closed by turning their taps to the right towards the wall

(Fig. 2).

4. Call your Service Engineer as soon as possible.

“Benchmark”Installation, Commissioning and Service

Record Log Book

Please ensure that your installer has completed the Installation and

Commissioning sections of the Log Book and hands the Log Book

over. The details of the Log Book will be required in the event of

any warranty work. Keep the Log Book in a safe place and ensure

that the relevant sections are completed at each subsequent

regular service visit.

Gas Tap

Heating Flow, Heating

Return and Mains

Water Inlet

Isolating Valves

Fig. 1

Fig. 2

All CORGI registered installers carry a CORGI identification card

and have a registration number. Both should be recorded in your

boiler Log Book. You can check your installer is registered by

telephoning 01256 372300 or writing to:-

1 Elmwood,

Chineham Business Park,

Crockford Lane,

Basingstoke RG24 8WG

2.0 Operating the Boiler

2.1 Introduction

1. Your Potterton Performa 24 is a gas fired, room

sealed, powered flue combination boiler, providing

central heating for your home and mains fed

domestic hot water to taps and shower. It is fully

automatic and does not have a pilot light.

2. Priority is given to the hot water mode - when a

hot water tap is turned on the supply of heat to the

central heating circuit is interrupted.

2.2 Operating the Boiler

1. Ensure that the electricity and gas supplies are

turned on. Check that the central heating pressure

is between 0.5 and 1.0 bar (Fig. 3).

2. Turn the On/Off/Reset selector switch either

anti-clockwise from the off position (Fig. 5) to both

central heating and domestic hot water or

clockwise to domestic hot water only.

3. In either position the green “power”neon

( ) will illuminate (Fig. 4).

4. Position (i) In this position the central heating

will operate according to demand or provide

domestic hot water when a tap or shower is turned

on (Fig. 6). Priority is given to domestic hot water.

5. Position (ii) In this position hot water will be

provided when a tap or shower is turned on

(Fig. 7).

6. The boiler will light automatically on demand.

7. The orange “burner”neon ( ) will illuminate

when the boiler is operating and the main burner is

on (Fig. 4).

IMPORTANT: When the selector switch is in

the ‘0’(Off) position the electrical supply to the

boiler is isolated. The boiler will not operate

and the integral timer (if fitted) will require

resetting once the selector switch is set to

either Position (i) or Position (ii).

bar

Reset Burner On

Flame Failure

Power On

Reset

Position (ii)

(Hot Water)

Fig. 6

Fig. 7

Reset

OFF Position

Fig. 5

Fig. 4

Fig. 3

1. On/Off/Reset Selector Switch

2. Burner Neon

3. Power Neon

4. Reset Neon

5. Central Heating Temperature Control

6. Hot Water Temperature Control

7. Central Heating System Pressure Gauge

8. Optional Integral Timer Position

12 34 5 6 7 8

bar

Position (i)

(Central Heating or Hot Water)

2.0 Operating the Boiler

2.3 Temperature Control

1. Central Heating: The central heating hot water

flow temperature can be adjusted between 30°C

(± 5°C) minimum and 85°C (± 5°C) maximum.

2. Turn the control knob clockwise to increase the

temperature (Fig. 8).

3. In normal winter usage we recommend that the

central heating temperature be set at maximum.

4. Domestic Hot Water: The temperature of the

domestic hot water can be adjusted by turning the

control knob clockwise to increase up to a

maximum of 65°C (Fig. 9).

5. The temperature of the water is also dependent

on the water flow rate and the temperature of the

mains water coming into the house.

6. By slightly reducing the flow from the tap the

temperature will increase up to the maximum if

required.

7. The flow rate can be reduced down to as low

as 2.5 litre/min. The boiler will still recognise the

need to heat the water.

2.4 Safety Thermostat

1. Your Potterton Performa 24 is fitted with an

additional safety device, which shuts down the

boiler in the event of the system or the boiler

overheating.

2. If the device operates, the boiler will shut down.

To reset: Contact your Service Engineer - the

reset button is inside the appliance and resetting

by the user should not be attempted.

3. The cause of operation of the safety thermostat

should be determined by your Service Engineer.

2.5 Flame Failure Reset

1. The red reset neon ( ) will illuminate in the

event of the burner failing to light, or when

incomplete lighting of the burner occurs (Fig. 11).

2. Turn the selector switch fully anti-clockwise

against the spring pressure to the reset position,

hold for 2 seconds and release (Fig. 10). Set the

selector switch to the required position to light the

boiler.

3. If the reset neon illuminates repeatedly a fault

is indicated. Your Service Engineer should be

contacted as soon as possible.

Reset

Burner On

Flame Failure

Power On

Domestic Hot Water

Temperature Control

Fig. 8

Fig. 11

Central Heating

Temperature Control

Fig. 9

Reset Position

Reset

Fig. 10

2.0 Operating the Boiler

2.6 Central Heating System Pressure

1. The water pressure in the central heating

system is indicated by the pressure gauge.

2. With the system cold and the boiler not

operating the pressure should be between 0.5

and 1.0 bar. During operation the pressure

should not exceed 2.5 bar, and will normally be

between 1.0 and 2.0 (Figs. 12 & 13).

3. A pressure of 3 or greater indicates a fault.

The safety pressure relief valve will operate, at a

pressure of 3 (Fig. 14). It is important that your

Service Engineer is contacted as soon as

possible.

4. The minimum pressure for correct operation is

0.5. If the pressure falls below 0.5, this may

indicate a leak on the central heating system

(Fig. 15).

5. The system must be re-pressurised by your

Service Engineer.

2.7 To Shut Off the Boiler

1. For short periods: Turn the selector switch to

the Off position (Fig. 16).

2. For long periods: Turn off the selector switch

(Fig. 16), electricity and gas supplies.

If your home is to be left unoccupied for long

periods during cold weather the boiler and

whole system should be drained unless

equipped with frost protection.

3. Your installer will advise you about frost

protection and draining the system.

IMPORTANT: When the selector switch is in

the ‘0’(Off) position the electrical supply to

the boiler is isolated. The boiler will not

operate and the integral timer (if fitted) will

require resetting once the selector switch is

set to either Position (i) or Position (ii).

bar

ON/OFF/RESET

Selector Switch

Reset

OFF Position

Fig. 16

Fig. 20

Fig. 18

Normal Pressure (when cold)

Normal Pressure (operating)

Fig. 12

Fault

Fig. 13

Below Minimum

Fig. 14

Fig. 15

Pressure Gauge

3.0 Clearances and Check List

3.1 Clearances around the Boiler

(Figs. 17 & 18)

1. The minimum clear spaces needed around

the boiler measured from the casing are as

follows:

Top - 200mm

Bottom - 200mm

Both sides - 5mm

Front - 5mm (In Operation)

- 450mm (For Servicing)

2. These areas must not be obstructed in any

way. Blocking the clearance spaces may

result in the boiler overheating and damage

may occur.

3. The gas burning compartment of your boiler is

completely sealed from the room in which it is

fitted. Products from the combustion of gas are

vented to the outside through the flue terminal

which must be kept free from obstruction as this

would interfere with the correct operation of the

boiler.

4. The boiler may be installed in a cupboard if

these minimum clearances are kept. The

compartment should be large enough to house

the boiler and ancillary equipment only.

5. IT SHOULD NOT BE USED AS A STORAGE

CUPBOARD.

3.2 Check List

1. If a fault develops, or is suspected, call your

Service Engineer as soon as possible.

2. Go through the following check list before you

make contact.

a) Is the electricity supply on ?

b) Is the selector switch on (giving a green

“Power ON”light) and set for both Central

Heating and Domestic Hot Water ?

c) Is the red “Flame Failure”indicator lit ?

Turn the On/Off/Reset selector fully anti-

clockwise.

d) Is the gas supply on ?

e) Is the mains water supply turned on ?

f) Is the system pressure correct ?

g) Are the boiler temperature controls set high

enough ?

h) Is the time clock (if fitted) calling for central

heating ?

i) Is the room thermostat (if fitted) set high

enough ?

j) Are the radiator valves open ?

bar

Reset Burner On

Flame Failure

PowerOn

200mm Min

780mm

450mm

200mm Min

5mm Min

8mm Min

450mm Min

For Servicing

Purposes

Fig. 17

Fig. 18

In Operation

4.0 Cleaning and Spares

4.1 Cleaning the Outercase

The painted panels should be wiped with a damp

cloth and then dried completely. Do not use

abrasive cleaning agents.

4.2 Spare Parts

IMPORTANT - Only a competant person

should be used to service or repair this boiler.

1. Any repairs to the boiler will usually be the

responsibility of the Installer during the

guarantee period after which spare parts may be

obtained through approved Potterton stockists if

required.

2. Quote the appliance name, model number

and where possible the part number when

ordering spares. A parts list is included in the

Installation and Servicing Instructions.

3. The name, model number, and serial number

can be found on a label on the inner face of the

lower right hand case panel (Fig 19).

Information Label

Fig. 19

Potterton, Baxi UK Limited, Brownedge Road, Bamber Bridge, Preston, Lancashire. PR5 6SN

After Sales Service 08706 096 096

www.baxi.com

Comp No249070 - Iss 2 - 6/01922.030.1

Otros manuales para Performa 24

Tabla de contenidos

Otros manuales de Caldera de Potterton

Potterton

Potterton Ultra DV 40 Suplemento

Potterton

Potterton NXR4i Manual

Potterton

Potterton Promax Combi HE Plus A Range Instrucciones de instalación y mantenimiento

Potterton

Potterton PROFILE LPG 100e Guía del usuario

Potterton

Potterton Osprey CF 180 Instrucciones de instalación y mantenimiento

Potterton

Potterton Eurocondense five 125 kW Manual de usuario

Potterton

Potterton Performa System 12 HE Instrucciones de instalación y mantenimiento

Potterton

Potterton Promax System HE Guía del usuario

Potterton

Potterton Suprima 80 HE Manual de instrucciones

Potterton

Potterton Promax Combi HE Plus A Range Manual de instrucciones

Potterton

Potterton NXR4 Manual de instrucciones

Potterton

Potterton Eurocondense three Manual del propietario

Potterton

Potterton EC three 125 Manual de usuario

Potterton

Potterton Paramount two 60 Manual de usuario

Potterton

Potterton Ultra 2 Instrucciones de instalación y mantenimiento

Potterton

Potterton Gold HE A Range Instrucciones de instalación y mantenimiento

Potterton

Potterton BOA 68 Manual de funcionamiento

Potterton

Potterton Prorile Prima 30e Manual de usuario

Potterton

Potterton 15 HE Plus Instrucciones de instalación y mantenimiento

Potterton

Potterton Eurocondense five 400 kW Manual de usuario

Potterton

Potterton Performa 28 Manual de usuario

Potterton

Potterton Eurocondense Plus Manual de usuario

Potterton

Potterton Promax 15 HE Instrucciones de instalación y mantenimiento

Potterton

Potterton Sirius two FS 50 Manual de usuario

Manuales populares de Caldera de otras marcas

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manual de usuario

Radijator

Radijator BIO max 23.1 Manual de usuario

Brunner

Brunner BSV 20 Manual de usuario

Buderus

Buderus Logamax GB062-24 KDE H V2 Manual de usuario

UTICA BOILERS

UTICA BOILERS TriFire Manual de usuario

Joannes

Joannes LADY Series Manual

ECR International

ECR International UB90-125 Manual de instrucciones

Froling

Froling FHG Turbo 3000 Manual de usuario

Froling

Froling P4 Pellet 8 - 105 Manual de usuario

U.S. Boiler Company

U.S. Boiler Company K2 Manual de usuario

Henrad

Henrad C95 FF Manual de usuario

NeOvo

NeOvo EcoNox EF 36 Manual de usuario

Eco Hometec

Eco Hometec EC 25 COMPACT Manual de usuario

Viessmann

Viessmann VITODENS 200 Guía

Baxi

Baxi Prime 1.24 Manual de usuario

REXNOVA

REXNOVA ISA 20 BITHERMAL Manual de usuario

Radiant

Radiant R2K 55 Manual

Worcester

Worcester Greenstar 36LXi Manual de usuario