POSIFLEX XT-5515: XT-5515Pro Manual de usuario
1
Package Contents
15” P-CAP touch terminal with Gen 7E or Gen 8E base…………….(x 1)
Power adapter…………………………………………………………(x 1)
Power cord……………………………………………………………(x 1)
User manual…………………………………………………………..(x 1)
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise.
The manufacturer is by no means responsible for any damage or hazard caused by improper
application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況
下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir des
enfants.
XT-5315/5515/5515Pro
P-CAP Touch Terminal
User Manual
16760900030 Ver. B0
http://www.posiflex.com
2
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a safeguard (for
example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a
battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or
the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler une sauvegarde
(par exemple, dans le cas de certains types de batterie au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou écrasement ou
coupure mécanique d'une batterie pouvant entraîner une explosion.
Laisser une batterie dans un environnement environnant à des températures
extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide ou de
gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse pouvant
provoquer une explosion ou une fuite de liquide ou de gaz inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。
Views of XT-5315/5515/5515Pro with Gen 7E Base
Front View
XT-5315/5515/5515Pro
P-CAP Touch Panel
LED indicator
Gen 7E Base
3
Rear View
Side View
Bottom View
Cable Holder
Cable Exit
Cable Cover
Neck Cover
HDD Cover
Cable Exit
Power Button
Brightness Adjustment Button ＋
Brightness Adjustment Button －
Rubber Feet with Fixing Screw
Rubber Feet with Fixing Screw
4
Views of XT-5315/5515/5515Pro with Gen 8E Base
Front View
Rear View
Side View
XT-5315/5515 /5515Pro
P-CAP Touch Panel
HDD Cover
Cable Cover
Neck Cover
Cable Exit
LED indicator
Power Button
Brightness Adjustment Button ＋
Brightness Adjustment Button －
Gen 8E Base
5
Bottom View
View of I/O Interface of XT-5315/5515
View of I/O Interface of XT-5515Pro
Rubber Feet with Fixing Screw
Line Out/MIC-In
Combo Jack
USB 2.0
Ports
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Ports
12V BAT Port
DC IN
Power
Connector
Rubber Feet with Fixing Screw
RJ-50 COM Ports
Line Out/MIC-In
Combo Jack
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Port
12V BAT Port
DC IN
Power
Connector
RJ-50 COM Ports
UPS Battery
Compartment
Power Adapter
Compartment
PoweredUSB
Compartment
HD Compartment
HDMI Port
6
Positioning your POS for a Perfect Viewing Angle
The adjustable bases designed for XT-5315/5515/5515Pro come in two models,
Gen 7E/8E, and allow you to determine an ideal position for your terminal by
using its unique tilt adjustment mechanism. As the below figures suggest, both
bases provide three standard positioning solutions for your terminal: Flat
Folded mode, Low Profile mode, and Full Extended mode.
XT-5315/5515/5515Pro with Gen 7E Base
Flat Folded mode
Low Profile mode
Full Extended mode
XT-5315/5515/5515Pro with Gen 8E Base
Flat Folded mode
Low Profile mode
Full Extended mode
In general, XT-5315/5515/5515Pro will be set up beforehand in Flat Folded
mode and then packaged into the box for shipping. After it is unpacked, you
may re-adjust the terminal in either Low Profile mode or Full Extended mode
according to your situation. Below will provide instructions on how to adjust
the specific base connected to the POS system. As a reminder, please be
careful not to touch the LCD panel while setting up the tilt angle.
XT-5315/5515/5515Pro with Gen 7E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5315/5515/5515Pro
with Gen 7E base.
1. Unpack XT-5315/5515/5515Pro, which is
supposed to be set in flat folded mode, out of
the package box and then lay your POS
system on a flat surface.
2. Steady the base with one hand, and then tilt
the screen downwards.
7
3. Position your terminal in Full Extended mode
3.1 After grabbing the bottom edge of the screen with your hand, gently
move the screen upward until the screen is locked into place with a
click sound.
3.2 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
3.3 With the screen facing toward you, tilt the screen up or down to your
desired angle. Please do not press on the LCD panel while setting up
the tilt angle.
3.4 Remove the cable cover from the base.
3.5 Fix the base with two #/6/32-14L screws.
Lever
Lower
hook
8
4. Return your terminal back to Flat Folded mode from Full Extended
mode.
4.1 Remove the cable cover from the base.
4.2 Remove the two screws from the base.
4.3 Tilt your screen in a horizontal position.
4.4 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, move the display downwards
until the lever is lifted off the hook as shown in the figure.
Remove the two screws.
Hook
Lever
9
4.5 Push the cable cover back.
4.6 Tilt the screen again to the horizontal
position.
5. Position the terminal in Low Profile mode.
5.1 Follow Step 4 to set up the termimal in Flat
Folded mode.
5.2 Tilt the screen all the way down
5.3 To tilt screen up or down to your desired
angle, please be advised to keep the base
steady with one hand to do so. Do NOT
press on the LCD panel while setting up the
tilt angle.
XT-5315/5515/5515Pro with Gen 8E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5315/5515/5515Pro
with Gen 8E base.
1. Unpack XT-5315/5515/5515Pro, which is
supposed to be set in flat folded mode, out
of the package box and then lay your POS
system on a flat surface.
2. While steadying the terminal with your
hand holding onto the base, tilt the screen
down.
10
3. Push the cable cover outwards to remove
it from the base.
4. Position your terminal in Full Extended mode.
4.1 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
4.2 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the tilt
angle.
4.3 Fix the base with two #/6/32-14L screws.
Lower
hook
Lever
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Terminal táctil de POSIFLEX
POSIFLEX
POSIFLEX HS-2510W-2D Manual de usuario
POSIFLEX
POSIFLEX PST-7000 Series Manual de usuario
POSIFLEX
POSIFLEX FT-6315 Manual de usuario
POSIFLEX
POSIFLEX MT-4210A Manual de usuario
POSIFLEX
POSIFLEX KS-6115 Manual de usuario
POSIFLEX
POSIFLEX XT-2614Q Manual de usuario
POSIFLEX
POSIFLEX Jiva KS-6615 Series Manual de usuario
POSIFLEX
POSIFLEX JIVA HS-3310A Manual de usuario
POSIFLEX
POSIFLEX XT- 3015 Manual de usuario
POSIFLEX
POSIFLEX HS-3510W-E Manual de usuario
POSIFLEX
POSIFLEX HT-3200 SERIES Manual de usuario
POSIFLEX
POSIFLEX PD - 7301 Series Manual de usuario
POSIFLEX
POSIFLEX KS - 6815 Manual de usuario
POSIFLEX
POSIFLEX PS-3416 Manual de usuario
POSIFLEX
POSIFLEX XP-3000 Series Manual de usuario
POSIFLEX
POSIFLEX Jiva TP-5815 Pro series Manual de usuario
POSIFLEX
POSIFLEX Jiva LT 8015 Manual de usuario
POSIFLEX
POSIFLEX HT-4600 Series Manual de usuario
POSIFLEX
POSIFLEX TX-2101 Manual de usuario
POSIFLEX
POSIFLEX Jiva KS-6215 Series Manual de usuario
