POSIFLEX PS-3415 Manual de usuario

Package Contents

Fanless LCD touch terminal…….(x 1)

Power adaptor…………………...(x 1)

Power cord………………………(x 1)

User Manual……………………..(x 1)

Recovery DVD………………….(x 1)

(for pre-loaded OS model only)

FCC NOTES

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential environment this

equipment may cause radio interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than

the authorized technicians. The user should consult his/her dealer for the problem happening.

Warranty voids if the user does not follow the instructions in application of this merchandise.

The manufacturer is by no means responsible for any damage or hazard caused by improper

application.

警告使用者

此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況

下，使用者會被要求採取某些適當的對策。

SAFETY INSTRUCTIONS

This equipment is not suitable for use in locations where children are likely to be present.

PS-3415/3415E

Fanless LCD Touch Terminal

User Manual

13110902040 Ver. C0

CONSIGNES DE SÉCURITÉ

Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir des

enfants.

BATTERY CAUTION NOTES

Dispose of used batteries according to the instructions.

Replacement of a battery with an incorrect type that can defeat a safeguard (for

example, in the case of some lithium battery types)

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a

battery that can result in an explosion.

Leaving a battery in an extremely high temperature surrounding environment that

can result in an explosion or the leakage of flammable liquid or gas.

A battery subjected to extremely low air pressure that may result in an explosion or

the leakage of flammable liquid or gas.

BATTERIE ATTENTION NOTES

Jetez les piles usagées conformément aux instructions.

Remplacement d'une batterie avec un type incorrect qui peut annuler une sauvegarde

(par exemple, dans le cas de certains types de batterie au lithium)

Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou écrasement ou

coupure mécanique d'une batterie pouvant entraîner une explosion.

Laisser une batterie dans un environnement environnant à des températures

extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide ou de

gaz inflammable.

Une batterie soumise à une pression atmosphérique extrêmement basse pouvant

provoquer une explosion ou une fuite de liquide ou de gaz inflammable.

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。

Product Features

Fanless terminal

Intel® Celeron® Bay Trail J1800 Celeron processor, up to 2.58 GHz,

Dual Core, 1MB Cache for PS-3415 /

Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz) for PS-

3415E

Foldable base that allows PS Series to be configured into different

configurations

Projected-capacitive touch

Integrated structure for side mount upgrade kit:

SA-105/205/305/405/505; back mount display: LM-6807U / 6810U and

PD-360R/360UE/2609UE/6807U;

40-key dynakey attachment with MSR or RFID option:

KP-500

Water resistant structure designed for easy cleaning

Views of the PS-3415/3415E

Front View

Rear View

Left Side View Right Side View

Bottom View

View of I/O Interface

Top I/O Ports Rear I/O Ports

COM4 Port

Parallel (LPT) Port

Connector

USB 2.0 Port

PS/2_KB Pin Header

※

The top I/O ports are provided for COM-based and USB-based peripheral

devices, for example, customer display.

Bottom I/O Ports

RJ45 LAN Port

USB 2.0 Port

VGA Port

COM Port

(COM3/COM2/COM1)

RJ11 Cash Drawer Port

12VDC-IN Power Jack

Positioning your POS for a Perfect Viewing Angle

The adjustable Gen7 base is designed to help you determine an ideal

position for PS-3415/3415E using its unique tilt adjustment mechanism.

As the below figures suggest, Gen7 base basically provides three

standard positioning solutions for your terminal: Flat Folded mode,

Low Profile mode, and Full Extended mode.

PS-3415/3415E with Gen7 Base

Flat Folded mode

Low Profile mode

Full Extended mode

In general, PS-3415/3415E will be set up beforehand in Flat Folded

mode and then packaged into the box for shipping. After it is unpacked,

you may re-adjust the terminal in either Low Profile mode or Full

Extended mode according to your situation. Below will provide

instructions on how to adjust the specific base connected to the POS

system. As a reminder, please be careful not to touch the LCD panel

while setting up the tilt angle. Please refer to the following instructions

on how to switch among different positioning modes to find an ideal

viewing angle for PS-3415/3415E with Gen7 base.

1. Unpack XT-3415/3415E, which is supposed

to be set in flat folded mode, out of the

package box and then lay your POS system

on a flat surface.

2. Steady the base with one hand, and then tilt

the screen downwards.

3. Position your terminal in Full Extended mode

3.1 After grabbing the bottom edge of the screen with your hand, gently

move the screen upward until the screen is locked into place with a

click sound.

3.2 Support the screen with one hand holding onto its bottom edge.

Then, while pulling the lever backwards, move the display upwards

until the lever is snapped into the lower hook to raise the screen as

shown in the below figure.

3.3 With the screen facing toward you, tilt the screen up or down to your

desired angle. Please do not press on the LCD panel while setting up

the tilt angle.

3.4 Remove the cable cover from the base.

3.5 Fix the base with two #/6/32-14L screws.

Lever

Lower

hook

4. Return your terminal back to Flat Folded mode from Full Extended

mode.

4.1 Remove the cable cover from the base.

4.2 Remove the two screws from the base.

4.3 Tilt your screen in a horizontal position.

4.4 Support the screen with one hand holding onto its bottom edge.

While pulling the lever backwards, move the display downwards

until the lever is lifted off the hook as shown in the figure.

Remove the two screws.

Hook

Lever

4.5 Push the cable cover back.

4.6 Tilt the screen again to the horizontal

position.

5. Position the terminal in Low Profile mode.

5.1 Follow Step 4 to set up the termimal in Flat

Folded mode.

5.2 Tilt the screen all the way down

5.3 To tilt screen up or down to your desired

angle, please be advised to keep the base

steady with one hand to do so. Do NOT

press on the LCD panel while setting up the

tilt angle.

Installing Optional Upgrade Kits and Peripherals

PS-3415/3415E can work with multiple optional upgrade kits and peripheral

devices, such as magnetic stripe reader (MSR), LCD monitor, cash drawer and

the like.

Before installing an optional upgrade kit and/or peripheral device, make sure

that the system is powered off and the external power source is removed from

the POS box to prevent electric hazard! Failure to follow the warning

description will void the product warranty!

For the detailed instruction, refer to each of the user manuals of the optional

upgrade kits and peripheral devices.

Connecting Power Adapter and I/O Cables

Before connecting power adapter and I/O cables to the I/O ports of PS series

terminal, please route and arranging the cables. Refer to the following step-by-

step instruction of cable routing and arrangement for the details. Here, an

equivalent model with GEN 7 base is taken below for example.

1. Press the circled section of the cable

cover with your thumb.

2. Pull out the cable cover.

3. Push and tilt the terminal to the end in

the direction as shown by the arrow.

4. Determine that the terminal is tilted to the

end, as shown in the right figure.

5. Press the circled section with two thumbs

and pull by force the two sides of the

locking hook with two forefingers as

indicated by the arrow.

6. Remove the neck cover from the base

stand.

7. Tilt the terminal slightly at a little angle in the direction as shown by the

arrow, making cables easily pass through the cable passage.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Terminal táctil de POSIFLEX

POSIFLEX

POSIFLEX MT-4210A Manual de usuario

POSIFLEX

POSIFLEX RT-5015 Manual de usuario

POSIFLEX

POSIFLEX RT-2015-G2 Manual de usuario

POSIFLEX

POSIFLEX KS-6115 Manual de usuario

POSIFLEX

POSIFLEX PS-3216A Manual de usuario

POSIFLEX

POSIFLEX Jiva KS-6615 Series Manual de usuario

POSIFLEX

POSIFLEX RT-1016A Manual de usuario

POSIFLEX

POSIFLEX TX-2101 Manual de usuario

POSIFLEX

POSIFLEX HC-1521 Series Manual de usuario

POSIFLEX

POSIFLEX DT-207 series Manual de usuario

POSIFLEX

POSIFLEX XT-3815-G2 Manual de usuario

POSIFLEX

POSIFLEX JIVA HS-2410W Manual de usuario

POSIFLEX

POSIFLEX KV-2000 Series Manual de usuario

POSIFLEX

POSIFLEX XT6315 Manual de usuario

POSIFLEX

POSIFLEX Cash Drawer CR400X Manual de usuario

POSIFLEX

POSIFLEX MT-4310W/R Manual de usuario

POSIFLEX

POSIFLEX XT-2614E Manual de usuario

POSIFLEX

POSIFLEX RT-1016A-G2 Manual de usuario

POSIFLEX

POSIFLEX KS - 6715 Manual de usuario

POSIFLEX

POSIFLEX MT-4308W Series Manual de usuario

POSIFLEX

POSIFLEX KS - 7212/X Manual de usuario

POSIFLEX

POSIFLEX XT-6015C Manual de usuario

POSIFLEX

POSIFLEX XP-3000 Series Manual de usuario

POSIFLEX

POSIFLEX Jiva LT 8015 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario