Polycom RealPresence Group Series Manual del propietario

www.polycom.com

Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproduced

or transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.

1725-67850-001A

Polycom®RealPresence® Group Series Media Center

Wall-Secured Setup Sheet Supplement

Polycom®RealPresence®Group Series Media Center with a

Single 55”, 65”, or 84“ Display or 55”or 65” Dual Displays

The Media Center components are heavy. Polycom recommends that two people perform the installation.

For more information about the components of the RealPresence Group Series Media Center, refer to the documentation at

http://support.polycom.com/PolycomService/support/us/support/video/group_series/group_packaged_solutions.html.

This product is intended for professional installation by a qualified installer. Before installing, ensure that the floor is

solid, level, and able to support the weight of the product. It is essential to correctly assess the strength of the wall to

ensure that the wall mounting hardware can safely anchor the product. If the installation of the wall mounting

hardware is not done correctly, the product could fall and cause severe injury or property damage. Polycom is not

liable for any injury or damage caused by mishandling or improper installation.

1Remove the base from packaging and flip the base over.

Attach the two foot covers to the base using four M10 x 50

flanged socket head cap screws per leg. Note that the legs

are not used and can be stored for future use.

(2) Foot Cover

1345-69027-001

Install the supplied floor glides on the legs, using one flat

washer and one split lock washer per glide. Ensure that the

flat washer is closest to the leg surface.

With the assistance of another person, flip the base over.

(4) Foot Glide

3Detach the pre-installed speaker bracket from each

vertical support by removing the 1/4-20 x 5/8 socket head

cap screws, flat washers, and lock washers. Set them

aside.

Wall Mount Bracket

1342-68996-001

Foot Cover

1345-69027-001

Unistrut®

1345-69027-001

3/8-16x1” Hex Head Screw

1601-25072-001

3/8-16 Flat Washer

1602-25065-001

3/8-16 Unistrut Nut with Spring

1600-25083-001

1/4 x 3.0” Lag Hex Screw

1601-12988-001

1/4 Washer

1602-61465-001

1/4-20x2.5” Hex Head Bolt

1601-61806-001

1/4-20 Toggle Anchor Insert

1650-28296-001

Polycom® RealPresence® Group Series Media Center Wall-Secured Setup Sheet Supplement 2

4Place the left vertical support on the base, aligning the

holes in the base with the holes in the bottom of the

vertical support. Attach the vertical support to the base

using three M10 x 25 flanged socket head cap screws per

vertical support. Do not fully tighten. Repeat with the

right vertical support.

6b - Option 1

48”

(1219 mm)

(2) Wall Brace Bracket

1342-68996-001

16”

(407 mm)

12”

(305 mm)

Note: Skip this step for 84” displays.

Install the camera mounting bracket using two 1/4-20x5/8”

socket head cap screws, two flat washers, and two lock

washers.

Mount the bracket in its fully extended position and lightly

tighten the screws so it remains in position.

You will lower the bracket later, when the camera is

mounted.

Attach the Wall Brace Bracket as

shown in the next figure. Always use

recommended wall mounting hardware

appropriate for your room wall.

IMPORTANT: Each installed Wall Brace Bracket must be able to

withstand horizontal pull force (away from wall) of at least 250N

(57 lbs).

6a - Option 1

Note that some previously assembled items are not shown

for clarity.

There are two options to brace the Media Center frame.

Directly bracing the Media Center to the wall is the preferred

option.

Position the Media Center frame as shown.

Room Wall

.3”

(8 mm)

Use an appropriate combination of wall

mounting hardware supplied with kit.

Recommended for solid wall applications:

(4) 1/4 x 3.0” Hex Lag Screw 1601-12988-001

(4) 1/4“ Washer 1602-61465-001

Recommended for drywall applications:

(4) 1/4-20 x 2-1/2” Hex Head Bolt 1601-61806-001

(4) 1/4“ Washer 1602-61465-001

(4) 1/4-20 Toggle Anchor Insert 1650-28296-001

Before proceeding to the next step, perform steps 5 through

8 in the Polycom RealPresence Group Series Media Center

Setup Sheet.

Polycom® RealPresence® Group Series Media Center Wall-Secured Setup Sheet Supplement 3

Note that some previously assembled items are not shown

for clarity.

The second option to brace the Media Center frame is with a

unistrut. At the predetermined location, mount the unistrut to

the wall as shown.

6a - Option 2

Position the Media Center frame away from the wall

as shown.

6b - Option 2

Room Wall

1.4”

(36 mm)

Unistrut

1310-28152-001

45.1”

(1145 mm)

Use an appropriate combination of wall

mounting hardware supplied with kit.

Recommended for solid wall applications:

(5) 1/4 x 3.0” Hex Lag Screw 1601-12988-001

(5) 1/4“ Washer 1602-61465-001

Recommended for drywall applications:

(5) 1/4-20 x 2-1/2” Hex Head Bolt 1601-61806-001

(5) 1/4“ Washer 1602-61465-001

(5) 1/4-20 Toggle Anchor Insert 1650-28296-001

IMPORTANT: The Unistrut should be able to withstand

a horizontal pull force (away from wall) of at least 500N

(114 lbs) when installed.

Attach the frame to the unistrut using the supplied hardware

as shown.

6c - Option 2

48”

(1219 mm)

(2) Wall Brace Bracket

1342-68996-001

16”

(407 mm)

12”

(305 mm)

(4) 3/8-16 x 1” Hex

Head Screw Bolt

1601-25072-001

(4) 3/8-16 Flat Washer

1602-25065-001

(4) 3/8-16 Spring Nut

1600-25083-001

Refer to the Polycom RealPresence Group Series Wall

Mount Setup Sheet and perform steps 11 through 21.

Attach the EagleEye IV camera to the camera mount

bracket using four M3 x 6 Phillips flat head screws.

Lower the camera mounting bracket from its extended

position by loosening the two screws installed in step 9.

When the camera is in the final position, tighten the

two screws.

Polycom®RealPresence® Group Series Media Center

Wall-Secured Setup Sheet Supplement

Polycom®RealPresence®Group Series Media Center with

Dual 42” AIO Displays