Polycom RealPresence EduCart 500 Manual
www.polycom.com
© 2017, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks associated with Polycom’s products are trademarks and/or service marks of
Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproduced
or transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.
Polycom, Inc.
6001 America Center Drive
San Jose, CA 95002, USA
1725-08449-001C
Polycom®RealPresence®EduCartTM 500
SETUP SHEET
Flat Screen Display
Note that your display may
look dierent than the display
shown in this document.
EagleEye IV Camera
Speakers
Base with
Locking Wheels
“Grab”
Handles
Basket
RealPresence
Group 500
Codec
Power Bar
H Frame
Poles
Back
Cover
Polycom® RealPresence® EduCartTM 500 Setup Sheet 2
3
2
Loosen and rotate the camera bracket and slide it
out to avoid hitting the display during installation.
The camera bracket is rotated for packaging and
must be rotated to the correct position.
1Place the base on the floor and lock the wheels.
Insert each pole into the base with the threaded
inserts lined up with the holes at the rear of the
base. Loosely insert two 3/8” bolts with flat washers
on the back side and one in the bottom of each pole.
Tighten with a 9/16” wrench.
Remove the basket and basket bracket from the
H frame by removing the two screws circled in
red.
4Attach the codec to the H frame with the
M3 x 8 Phillips pan head screws.
Polycom® RealPresence® EduCartTM 500 Setup Sheet 3
7
Remove the display from packaging. If possible,
leave the display on the bottom portion of the
packaging. Using four long M8 x 25 screws and
spacers between the H frame and the dislay, attach
the H frame to the rear of the display using the
holes indicated below. If the packaging interferes,
either cut the foam or lift the display out.
56Insert four M8 x 16 screws on the back of the frame
and hand tighten to about half way. The screws
must be loose to fit onto the cart.
Ensure that the cart casters are locked. With a
person on each side, lift the display, by the handles,
onto the cart at the desired height. Ensure that
all four M8 screws installed in step 6 are hooked
into the keyhole slots in the cart poles. Tighten the
four M8 screws through the holes.
If this system is not used with a Polycom-
supplied display, the display used must have
VESA 400 mm x 400 mm or 400 mm x 600 mm
mounting and must not exceed any of the
following parameters:
Diagonal size: 55” (1400 mm)
Depth: 2.6” (65 mm)
Weight: 66.1 lbs (30 kg)
Note that some displays require M6 screws
that are not supplied.
Polycom® RealPresence® EduCartTM 500 Setup Sheet 4
9
11
Adjust the handles by loosening the two screws
on each bar (four screws per side). Extend the
handle at or beyond the display by 1-2”. Replace
the screws and tighten. Use the same hole in the
series of holes on both sides. These handles will be
used to move the cart.
Place the speaker brackets grill forward and
directly under the display on the outside of the
poles. Attach them with U-shaped brackets using
nuts and a 7/16” wrench.
Attach the supplied bracket to the speaker. The
bracket can be spread open to fit over the speaker.
108 Loosen the two pre-mounted screws in the codec
power supply bracket above the codec. Slide the
power supply into the bracket and tighten the
two screws.
Polycom® RealPresence® EduCartTM 500 Setup Sheet 5
15 Attach the storage basket to the bottom of the H
bracket under the power bar using the two screws
removed in step 2.
Connect the speaker wires. Refer to the wiring
diagram at the end of this document for details.
14 Attach the vanity plate on the front of
the cart between the speakers.
12 Place the speaker inside the grill bracket and
fasten to the bracket with two 10-32 screws on
the rear side only.
13
6
Polycom® RealPresence® EduCartTM 500 Setup Sheet
16
Loosen the two screws on the camera bracket
and lower the camera shelf to the top of the
display. Tighten the screws. Route the camera
cable behind the camera bracket and through
the hole.
17
Attach the EagleEye IV camera to the camera
mounting bracket using four M3 x 6mm Phillips
flat head screws.
18 Attach and route the cables. Run the power cord
from the power bar, down the adjacent pole, and
exit the cord end at the hole at the bottom of the
pole. Run an ethernet cable the same way. Store
excess cable with the cable wrap bracket at the
bottom of the cart base. Refer to the wiring
diagram at the end of this document for details.
Only EduCart 500 components should be
plugged into the power outlet block. Do not
power any other electrical equipment from this
power outlet.
Polycom® RealPresence® EduCartTM 500 Setup Sheet 7
19 Install the magnetic back cover over the codec and
cables and fasten with the two supplied screws.
Child Safety Warnings:
Death or serious injury may occur when children climb on
audio and/or video equipment furniture. A remote control or
toys placed on the furnishing may encourage a child to climb
on the furnishing and as a result the furnishing may tip over
onto the child.
Relocating audio and/or video equipment to furniture not
specifically designed to support audio and/or video
equipment may result in death or serious injury due to
furniture collapsing or overturning onto a child.
Mains Input Rating:
Voltage: 100-240 VAC, 50/60Hz
Current: 3.4A (max)
Weight:
Assembled System: 144 lbs (65 Kgs)
Sampo 55” LED Display (Model PME55MA):
66.1 lbs (30 Kgs)
Regulatory Notices and General Warnings:
This equipment is intended for indoor use only.
This equipment is intended to be suitable for institutional use.
Do not use a power cord that is damaged. This could cause
fire or electric shock. Contact the manufacturer for a
replacement cord, if necessary.
Only use a power cord which is appropriately rated and
approved relevant to the country of use.
This equipment should be used only on even surfaces.
This equipment has lockable wheels which should be
applied while the cart is stationary.
When connecting to the mains supply, connect only to an
earthed supply outlet which is installed near the equipment
and is easily accessible.
Keep ventilation openings free from any obstructions.
The ambient operating temperature rating of this equipment
is 0 - 40ºC and should not be exceeded.
Do not immerse the system in any liquid or place any liquids
on it.
Do not spray liquids directly onto the system when cleaning.
Always apply the liquid first to a static-free cloth.
For further information concerning the individual components
of this equipment, please refer to the respective product
literature.
For support or service, please contact your Polycom®
distributor or go to Polycom Support at
www.polycom.com/support.
Polycom® RealPresence® EduCartTM 500 Setup Sheet 8
EduCart 500 Wiring Diagram
Otros manuales de Sistema de conferencias de Polycom
Polycom
Polycom Trio Series Manual de usuario
Polycom
Polycom Trio Series Manual de usuario
Polycom
Polycom ViewStation H.323 Manual de usuario
Polycom
Polycom HDX 8000 series Manual de usuario
Polycom
Polycom VSX 8800 Manual de instalación y operación
Polycom
Polycom RealPresence Group Series Manual de usuario
Polycom
Polycom RealPresence OTX Studio Manual de usuario
Polycom
Polycom VSX Series Manual de usuario
Polycom
Polycom MGC-25 Manual de usuario
Polycom
Polycom RPX HD 400 Series Cómo utilizar
Polycom
Polycom ViewStation SP128 Manual de usuario
Polycom
Polycom HDX 9000 Series Manual de usuario
Polycom
Polycom VSX Series Manual de servicio
Polycom
Polycom RealPresence Group Series Manual del operador
Polycom
Polycom SIP 3.0.2 Manual de servicio
Polycom
Polycom SoundStructure C16 Guía
Polycom
Polycom SoundStructure TEL1 Manual
Polycom
Polycom QSX Manual de servicio
Polycom
Polycom VVX 500 Manual de usuario
Polycom
Polycom RealPresence Trio 8500 Manual de usuario
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
