Polycom RealPresence Group Series Manual
Polycom®RealPresence®Group Series Media Center
with 65 Inch Dual Displays
SETUP SHEET
This supplement describes how to attach 65 inch dual displays on the Polycom®RealPresence®Group Series
Media Center. Follow the instructions in Setting Up the Polycom RealPresence Group Series Media Center,
1725-08510-00X, and use this supplement to replace the steps to install the displays.
Single 55/65 inch Lower Display Rail, 1354-67626-002
(2) Dual 65 inch Lower Display Rail Extension, 1354-68667-002
Dual 65 inch Center Top Display Rail, 1354-68669-001
(2) Dual 65 inch Upper Display Rail Extension, 1354-68671-001
(4) Display Mounting Bracket
Assembly
2342-67629-001
(4) M8 x 20 Button Head Cap Screw
1601-52713-001
(4) M8 Hex Flange Nut
1600-52845-001
(4) M10 x 25 Flanged Socket Head
Cap Screw
1601-67617-002
M8 Wrench
1102-68064-001
For more information about the components of the RealPresence Group Series Media Center,
refer to the documentation at
http://support.polycom.com/PolycomService/support/us/support/video/group_series/group_packaged_solutions.html.
The Media Center components are heavy. Polycom recommends that two people perform the installation.
www.polycom.com
© 2018, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks associated with Polycom’s products are trademarks and/or service marks of
Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproduced
or transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.
1725-68117-002B
Polycom RealPresence Group Series Media Center Setup Sheet 2
Install the lower display rail by aligning the holes in
the display rail with the holes in the vertical
supports. Attach with four M10 x 25 flanged socket
head cap screws. Do not fully tighten.
Install a lower display rail extension to each side of
the lower display rail using two M8 x 20 button
head cap screws and two M8 hex nuts per side.
Ensure the edge of the rail extension is 3.97 inches
from the inner cut edge of the bottom display rail.
Tighten using the supplied M8 wrench.
Attach an upper display rail extension to each end of the center top display rail using two M10 x 25 flanged
socket head cap screws per extension.
Polycom RealPresence Group Series Media Center Setup Sheet 3
Install the upper display rail assembly by aligning the holes in the display rail with the holes in the vertical
supports. Attach with two M10 x 25 flanged socket head cap screws per vertical support. Do not fully tighten.
Attach the rear panel by inserting the two tabs at the
bottom of the door into the slots in the base. This
serves as an alignment tool to ensure the frame is
properly aligned before tightening all bolts. Using
the L-key, tighten the socket head cap screws at
the bottom of the base, the lower display rail, and
the upper display rail. Remove the rear door.
On the back side, install a handle on both ends
of the bottom display rail.
Polycom RealPresence Group Series Media Center Setup Sheet 4
Install the display mount brackets on the display. For the LG display, position the display mounting bracket
using the sixth hole from the top with the top mounting hole on the display. The bottom hole on the display is
the seventh hole up from the bottom of the bracket.
For the Sampo display, position the third hole down from the top of the display bracket with the third hole
down from the top of the display. The bottom hole on the display lines up with the fifth hole up from the bottom
of the display bracket.
Install the supplied 1/4-20 x 3.5 inch socket head cap screws at the top of each display bracket. Leave the
screws adjusted up before mounting the display to the top rail.
Repeat with the second display.
With the assistance of another person, lift the display and position the display bracket hooks above the edge
of the upper horizontal display rail on the Media Center. Carefully lower the display onto the rail, ensuring the
hooks are fully engaged with the rail and that the outer most bracket is positioned within the safety tab on the
outer rail end (1). Repeat with the second display.
Adjust the leveler screws as needed to help eliminate any gap between the two displays when they are tightly
abutted (2).
Polycom RealPresence Group Series Media Center Setup Sheet 5
Center the displays on the Media Center. Insert one M6 x 16 flanged button head screw into each outer
display bracket to lock the displays.
Power Rating:
Voltage rating: 100-240 VAC, 50/60Hz
Maximum power consumption (configured with Grou
Series 500 codec and EagleEye IV camera under full
load operating conditions):
231.4W with Sampo display
165.4W with LG display
Approximate system weight (including displays,
codec, camera, and sound system):
715 lbs. with Sampo display
689 lbs. with LG display
Regulatory Notices:
This equipment is intended for indoor use only.
Only use this equipment with the displays supplied by
Polycom.
Do not use a power cord that is damaged. This could cause
fire or electric shock. Contact the manufacturer for a
replacement cord, if necessary.
Only use a power cord which is appropriately rated and
approved relevant to the country of use.
This equipment should be used only on even surfaces.
When moving or positioning the system, only use the
handles located at the bottom of the display rail at the rear
of the unit.
This equipment has lockable wheels which should be
applied while the cart is stationary.
When connecting to the mains supply, connect only to an
earthed supply outlet which is installed near the equipment
and is easily accessible.
Keep ventilation openings free from any obstructions.
The ambient operating temperature rating of this equipment
is 0 - 40ºC and should not be exceeded.
Do not immerse the system in any liquid or place any liquids
on it.
Do not spray liquids directly onto the system when cleaning.
Always apply the liquid first to a static-free cloth.
For further information concerning the individual components
of this equipment, please refer to the respective product
literature.
For support or service, please contact your Polycom®
distributor or go to Polycom Support at
www.polycom.com/support.
p
Otros manuales para RealPresence Group Series
24
Tabla de contenidos
Otros manuales de Sistema de conferencias de Polycom
Polycom
Polycom SpectraLink 6000 System Manual de usuario
Polycom
Polycom Digital Signage 2000 Manual de usuario
Polycom
Polycom ViaVideo Manual operacional
Polycom
Polycom IPOWER 9000 Manual de usuario
Polycom
Polycom ViewStation SP128 Manual de usuario
Polycom
Polycom VIEWSTATION EX Manual de usuario
Polycom
Polycom VSX 8000 Series Manual de usuario
Polycom
Polycom V500 Manual de servicio
Polycom
Polycom HDX 4500 Manual de usuario
Polycom
Polycom ViaVideo Manual de usuario
Polycom
Polycom RealPresence Group Series Instrucciones de montaje
Polycom
Polycom HDX 9001 Instrucciones de uso
Polycom
Polycom HDX Series Instrucciones de montaje
Polycom
Polycom Viewstation 128 Manual de usuario
Polycom
Polycom HDX Desktop Systems Manual de usuario
Polycom
Polycom RealPresence Group Series Manual de usuario
Polycom
Polycom VSX Series Manual de usuario
Polycom
Polycom HDX 9000 Series Manual de usuario
Polycom
Polycom ReadiManager LX 100 Manual de usuario
Polycom
Polycom CX5000 Guía de referencia rápida
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
