Planet IGS-10020PT Manual de usuario
L2+ Industrial 8-Port 802.3af/at PoE
Managed Switch
IGS-10020PT/IGS-10020HPT
Quick Installation Guide
Table of Contents
1. Package Contents................................................................................. 3
2. Requirements....................................................................................... 4
3. Wiring the Power Inputs ....................................................................... 5
3.1 Grounding the Device..................................................................... 7
4. Terminal Setup..................................................................................... 8
4.1 Logging on to the Console.............................................................. 9
4.2 ConguringIPAddress ................................................................. 10
5. Starting Web Management .................................................................. 13
5.1 Logging in to the Industrial Managed PoE+ Switch ......................... 14
5.2.SavingConguration .................................................................... 16
6. RecoveringBacktoDefaultConguration ............................................. 18
7. Customer Support ............................................................................... 19
3
1. Package Contents
Thank you for purchasing PLANET L2+ Industrial Managed Gigabit PoE+
Switch. The descriptions of these models are as follows:
Model RJ45 Ports PoE+ Ports SFP Ports
IGS-10020PT
882
IGS-10020HPT
“Industrial Managed PoE+ Switch” mentioned in this Quick Installation
Guide refers to the above models.
Open the box of the Industrial Managed PoE+ Switch and carefully unpack it.
The box should contain the following items for each of the three models:
Item IGS-10020PT IGS-10020HPT
QR Code Sheet
DIN-railKit
WallMountingKit
DB9 to RJ45 Interface RS232 Console Cable
RJ45 Dust Cap 9
SFP Dust Cap 2
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zWorkstations running Windows 2003/2008/2012/7/8/10/11, MAC OS X or
later,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zSerial Port Connection (Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such
asHyperTerminalincludedinWindowsXP/2003,puttyorteraterm.
Serial cable -- one end is attached to the RS232 serial port, while the
other end to the RJ45 console port of the Industrial Managed PoE+
Switch.
zEthernet Port Connection
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zNetworkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
zThe above PC is installed with Web browser.
It is recommended to use Chrome 98.0.xxx or above to access
the Industrial Managed PoE+ Switch. If the Web interface of the
Industrial Managed PoE+ Switch is not accessible, please turn
off the anti-virus software or firewall and then try it again.
5
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed PoE+ Switch indicates a DC inlet
power socket and consists of one terminal block connector within 6 contacts.
Please follow the steps below to insert the power wire.
1. Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1,
or Contacts 5 and 6 for Power 2.
zIGS-10020PT: 48V-54V DC
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-10020PT Upper Panel
zIGS-10020HPT: DC 12-48V
PWR1 PWR2
Fault
DI1 DO0 DO1DI0 GNDGND
Max. fault loading: 24V, 1A
DC Input:
12-48V , 7A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-2: IGS-10020HPT Upper Panel
6
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
V1+ V1- V2+ V2-
Power 1
(DC1)
Power 2
(DC2)
Model Positive (+) Pin Negative(-)Pin
IGS-10020PT
IGS-10020HPT Pin 1 / 5 Pin 2 / 6
The wire gauge for the terminal block should be in the range
from 12 to 24AWG.
7
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Earth Ground
EMD(Lightning)DAMAGEISNOTCOVEREDUNDERWARRANTY.
8
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type serial (console) port of the Industrial
Managed PoE+ Switch. The console port of the Industrial Managed PoE+
Switch is DCE already, so that you can connect the console port directly
through PC without the need of null modem.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Industrial Managed PoE+ Switch Console Connectivity
A terminal program is required to make the software connected to the
Industrial Managed PoE+ Switch. Windows’ Hyper Terminal program may be
a good choice. The Hyper Terminal can be accessed from the Start menu.
1. Click START, then Programs, Accessories and then Hyper Terminal.
2. When the following screen appears, make sure that the COM port should be
conguredas:
Baud: 115200
Parity:None
Data Bits: 8
Stop Bits: 1
FlowControl:None
Figure 4-2: COM Port Conguration
9
4.1 Logging on to the Console
Once the terminal has been connected to the device, power on the Industrial
Managed PoE+ Switch and the terminal will display “running testing
procedures”.
The following console screen is based on the IGS-10020HPT.
The display of the IGS-10020PT is the same as that of the IGS-
10020HPT.
Then, the following message asks to log in user name and password as
shown in Figure 4-3. Please enter the factory default user name “admin” and
password “admin”.
UserName:admin
Password: admin
Figure 4-3: Console Login Screen
1. For security reason, please change and memorize the
new password after this first setup.
2. Only accept command in lowercase letter under console inter-
face.
10
4.2 ConguringIPAddress
The Industrial Managed PoE+ Switch is shipped with default IP address shown
below:
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Industrial
Managed PoE+ Switch, please use the procedure as follows:
Display of the current IP Address
1.Atthe“#” prompt, enter “show ip interface brief”.
2. The screen displays the current IP address shown in Figure 4-4.
Figure 4-4: IP Information Screen
Otros manuales para IGS-10020PT
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet IGS-501T Manual de usuario
Planet
Planet GSD-Series Manual de usuario
Planet
Planet IGSW-24040T Manual de usuario
Planet
Planet FNSW-1600 Manual de usuario
Planet
Planet WGSW-14020 Manual de usuario
Planet
Planet FSD-804P Manual de usuario
Planet
Planet ISW-800T-M12 Manual de usuario
Planet
Planet WGS-5225-8UP2SV Manual de usuario
Planet
Planet IGS-1000 Series Manual de usuario
Planet
Planet IFGS-1022TF Manual de usuario
Planet
Planet FSD-624SF Manual de usuario
Planet
Planet IGS-6325-20T4C4X Manual de usuario
Planet
Planet FNSW-1601 Manual de usuario
Planet
Planet GS-4210 SERIES Manual de usuario
Planet
Planet POE-152 Manual de usuario
Planet
Planet IGSW-24040T Manual de usuario
Planet
Planet VC-820M Manual de usuario
Planet
Planet WGSD-1022 Manual de usuario
Planet
Planet XGS-6311 Series Manual de usuario
Planet
Planet FSP-804P Manual de usuario
