Planet WGS-5225-8MT Manual de usuario

Industrial L2+ 8-Port 10/100/1000T M12

Wall-mount Managed Switch

WGS-5225-8MT

Quick Installation Guide

Table of Contents

1. Package Contents ....................................................................................... 3

2. M12 X-coded cable ..................................................................................... 4

2.1 M12 X-coded Connector Pin Assignment ................................................ 4

2.2 M12 (8-pin, X-coded Male) to RJ45 (8-pin) Straight-through UTP Cabling. 4

2.3 Connecting M12 Cable to the WGS-5225-8MT ........................................ 5

3. M12 DC Power Cable .................................................................................. 7

4. Requirements ............................................................................................. 8

5. Hardware Installation .................................................................................. 9

5.1 Wall Mount Installation......................................................................... 9

5.2 Wall Hanging Installation.....................................................................10

5.3 Magnet Installation .............................................................................11

5.4 DIN-rail Mounting ...............................................................................12

6. Web Login.................................................................................................14

6.1 Starting Web Management ..................................................................14

 6.2 SavingCongurationviatheWeb ........................................................16

7. RecoveringBacktoDefaultConguration.....................................................17

8. Customer Support .....................................................................................18

1. Package Contents

Thank you for purchasing PLANET Industrial L2+ 8-Port 10/100/1000T M12 Wall-

mount Managed Switch. The table below shows the model with the number of

ports

Model Name 10/100/1000T M12 ports, 8-pin X-coded female connector

WGS-5225-8MT 8

In the following sections, unless specied, the term “Wall-mount Managed

Switch” mentioned in this quick installation guide refers to the above model.

Open the box of the Wall-mount Managed Switch and carefully unpack it. The box

should contain the following items:

The Wall-mount

Managed Switch x 1

Quick Installation

Guide x 1 pc

Wall-mounted Kit x

1 set

Magnet Kit x

1 set

DIN-rail Kit x 1

set

2m 8-pin X-coded M12-to-RJ45

UTP Cable x 1

1.2m M12 Power Cable

x 1

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. M12 X-coded cable

2.1 M12 X-coded Connector Pin Assignment

The WGS-5225-8MT front panel provides eight 10/100/1000BASE-T Ethernet

ports in the form of M12 8-pin X-coded female connector. These ports are

designed for Ethernet equipment connection through Cat5/5e UTP cables. The M12

8-pin X-coded input interface pinout is shown below:

Pin Con

1DA+

2DA

3DB+

DD+

DB4

DC+

8-pin M12 X-coded Female 10/100/1000T Connector Pin Assignment

2.2 M12 (8-pin, X-coded Male) to RJ45 (8-pin) Straight-through

UTP Cabling

M12 X-coded Male

Connector Pin No.

MDI

1000BASE-T Signal ID T568B Color RJ45 Connector

Pin No.

1BI_DA+ white/orange 1

2BI_DA- orange 2

3BI_DB+ white/green 3

4BI_DB- green 6

5BI_DD+ white/brown 7

6BI_DD- brown 8

7BI_DC- White/blue 5

8BI_DC+ blue 4

Note

As each Ethernet port of the Wall-mount Managed Switch is

running in auto negotiation mode, make sure the Ethernet ports of

the corresponding Ethernet devices are also running in auto nego-

tiation mode; otherwise, the Ethernet performance will be poor.

2.3 Connecting M12 Cable to the WGS-5225-8MT

Note

Follow the steps below to connect M12 cables to the WGS-

5225-8MT.

Step 1: Turn counterclockwise to remove the waterproof caps of an M12

connector and power input.

Step 2: Insert the M12 UTP male connector into the M12 female Gigabit Ethernet

port of the Wall-mount Managed Switch.

Step 3: Turn clockwise to tighten the cable of the M12 connector and make sure

the connection is tight.

Step 4: Insert the M12 power female connector into the M12 male port of the

power input.

Step 5: Turn clockwise to tighten the cable connecting to the M12 power

connector.

Caution

To have the vibration-proof effect, connectors must be totally tight-

ened.

3. M12 DC Power Cable

Pin Assignment

The front panel of the Wall-mount Managed Switch provides one M12 DC power

5-pin male connector for DC power input. Please use the power cable with the M12

DC power 5-pin female connector from the Wall-mount Managed Switch package

for DC power input. The M12 DC power cable pin assignment is shown below:

M12 DC power cable pin assignment and wiring code

V1−

V1+

V2−

V2+

V1 positive (+) pin = blue cable

V1 negative (-) pin = white cable

V2 positive (+) pin = black cable

V2 negative (-) pin = brown cable

Note

Make sure you connect the correct power pin to your DC power

source.

1. The wire gauge for the power cable should be in the range of 12

~ 24 AWG.

2. The DC power input range is 9 ~ 48V DC.

4. Requirements

zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,

Linux, UNIX, or other platforms are compatible with TCP/IP protocols.

zWorkstations are installed with Ethernet NIC (Network Interface Card)

zEthernet Port Connection

Network cables -- Use network (UTP) cables with M12 (X-coded) and RJ45

connectors.

The above PC is installed with Web browser.

Note

It is recommended to use Internet Explorer 8.0 or above to access

the Wall-mount Managed Switch. If the Web interface of the Wall-

mount Managed Switch is not accessible, please turn off the anti-

virus software or firewall and then try it again.

5. Hardware Installation

5.1 Wall Mount Installation

To install the Wall-mount Managed Switch on the wall, simply follow the following

steps:

Step 1: It is required 4 holes with 8mm diameter on the wall; the distance

between the 2 holes is 230 mm and the line through them must be

horizontal.

230mm

124mm

Ø4mm

6mm

Ø8mm

Step 2: Install a conductor pipe inside the board hole and ush the edge of the

conductor pipe with the wall surface.

Step 3: Screw the bolts into the conductor pipe. The Wall-mount Managed Switch

is between bolts and conductor pipe, as shown below.

ACTLNK

1000

100

SYS

PWR

180W

240W

SFP

120W

60W

5 731

6 842

13 15119

14 161210

PoE

SFP

17 18

WGS-4215-16P2S

Managed

Fiber

PoE+ Magnet Mounting

PoE-in-Use

LNK/ACT

PoE Usage

V+

Ground

DC Input Range

48-56V , 5.8A max.

WGS-5225-8MT

Managed

Bypass Relay Magnet Mounting

Alarm

PWR 2

PWR 1

Ring

R.O.

Pin Con

1 DA+

2 DA

3 DB+

DD+

DB4

DC+

2468

1357

DC Input:

9V-48V

, 1.3A max.

Power

Normal

Power

Failure

10/10010/10010/10010/100

10001000

LNK/ACTLNK/ACT

Bypass Relay

230mm

124mm

5.2 Wall Hanging Installation

To hang the Wall-mount Managed Switch on the wall, simply follow the following

steps:

Step 1: Drill 2 holes (one hole on each side) with 8mm diameter on the wall; the

distance between the 2 holes is 230 mm and the line through them must

be horizontal.

Step 2: Place two anchors inside the board hole by hammering them. Then screw

the two screws leaving a space of 2mm apart as shown in the circled

diagram below.

1 2

ACTLNK

1000

100

SYS

PWR

180W

240W

SFP

120W

60W

5 731

6 842

13 15119

14 161210

PoE

SFP

17 18

WGS-4215-16P2S

Managed

Fiber

PoE+ Magnet Mounting

PoE-in-Use

LNK/ACT

PoE Usage

V+

Ground

DC Input Range

48-56V , 5.8A max.

WGS-5225-8MT

Managed

Bypass Relay Magnet Mounting

Alarm

PWR 2

PWR 1

Ring

R.O.

Pin Con

1 DA+

2 DA

3 DB+

DD+

DB4

DC+

2468

1357

DC Input:

9V-48V

, 1.3A max.

Power

Normal

Power

Failure

10/10010/10010/10010/100

10001000

LNK/ACTLNK/ACT

Bypass Relay

2mm

4mm Screw

Step 3: The switch, shown in the picture below, can now be hung on the wall.

1Place against a wall

2Hang up

ACTLNK

1000

100

SYS

PWR

180W

240W

SFP

120W

60W

5 731

6 842

13 15119

14 161210

PoE

SFP

17 18

WGS-4215-16P2S

Managed

Fiber

PoE+ Magnet Mounting

PoE-in-Use

LNK/ACT

PoE Usage

V+

Ground

DC Input Range

48-56V , 5.8A max.

WGS-5225-8MT

Managed

Bypass Relay Magnet Mounting

Alarm

PWR 2

PWR 1

Ring

R.O.

Pin Con

1 DA+

2 DA

3 DB+

DD+

DB4

DC+

2 4 6 8

1 3 5 7

DC Input:

9V-48V

, 1.3A max.

Power

Normal

Power

Failure

10/10010/10010/10010/100

10001000

LNK/ACTLNK/ACT

Bypass Relay

4mm Screw

Tabla de contenidos

Otros manuales de Cambiar de Planet

Planet

Planet DHR-800 Manual de usuario

Planet

Planet ISW-500 Manual de usuario

Planet

Planet FNSW-2402 Manual de usuario

Planet

Planet GS-4210 SERIES Manual de usuario

Planet

Planet WGS-4215-T Manual de usuario

Planet

Planet GSD-604HP Manual de usuario

Planet

Planet POE-152 Manual de usuario

Planet

Planet GSD-805 Manual de usuario

Planet

Planet GS-5220 Series Manual de usuario

Planet

Planet XGS-6320-8X8TR Manual de usuario

Planet

Planet IGS-504HPT Manual de usuario

Planet

Planet IGS-4215 Series Manual de usuario

Planet

Planet IFGS-1022TF Manual de usuario

Planet

Planet GSW-4804SF Manual de usuario

Planet

Planet SGS-6341 Series Instrucciones de instalación

Planet

Planet FNSW-4800 Manual de usuario

Planet

Planet HPOE-460 Manual de usuario

Planet

Planet MGS-5220-8P2X Manual de usuario

Planet

Planet FSD-504HP Manual de usuario

Planet

Planet LRP-822CS Manual de usuario

Planet

Planet GSW-1602SF Manual de usuario

Planet

Planet WSW-2401 Manual de usuario

Planet

Planet POE-1200 Manual de usuario

Planet

Planet WGSW-5240 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario