Planet 802.11g Wireless Access Point / Bridge... Manual de usuario

802.11g Wireless Access Point/ Bridge

WAP-4000

User sManual

be reproduced, transmitted, transcribed, stored in aretrieval system, or translated into any language

or computer language,in any form or by any means,electronic, mechanical,magnetic, optical,

chemical, manual or otherwise, without the prior written permission of PLANET.

PLANETmakes no representations orwarranties, either expressed orimplied, with respectto the

contentshereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose.Any software described in this manual is sold or licensed "as is".Should the programs

prove defective following their purchase, the buyer (and not this company,itsdistributor,or itsdealer)

assumes the entire cost of all necessary servicing, repair,and any incidental or consequential

damages resulting from any defect in the software. Further, this company reserves the right to revise

this publication and to make changes from time totime in the contentshereof withoutobligation to

notify any person ofsuch revision orchanges..

All brand and product names mentioned in this manual are trademarks and/or registered trademarks

of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limitsfor aClass Bdigital device,

pursuant toPart 15 of FCC Rules.These limitsaredesigned toprovide reasonable protection

against harmful interference in aresidential installation. This equipment generates, uses, and can

radiateradio frequency energyand, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,there is no guarantee that

interference will not occur in aparticularinstallation.If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment offand

on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorientor relocate the receiving antenna.

2. Increase the separation between the equipmentand receiver.

3. Connect the equipmentinto an outlet on acircuitdifferent from thatto which the receiver is

connected.

4. Consult the dealer or an experienced radio technician forhelp.

FCC Caution:

Toassurecontinued compliance.(example-use only shielded interface cables when connecting to

computeror peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject tothe Following two

conditions: (1) This device may not cause harmful interference, and (2 )this Device must accept any

interference received, including interference thatmay cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

orderto avoid the possibility of exceeding the FCC radio frequency exposure limits,human proximity

to the antenna shall not be less than 20 cm(8 inches) during normal operation.

R&TTE Compliance Statement

This equipmentcomplies with all the requirementsof DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENTAND THE COUNCILOF 9March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of theirconformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC(Telecommunications Terminal

Equipmentand Satellite EarthStation Equipment) As of April 8,2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it.However,

special attention must be paid to the dangers of electric shock and static electricity when working with

electrical equipment.All guidelines of this and of the computer manufacture must thereforebe allowed

at all times to ensure the safe use of the equipment.

Revision

User s Manual for PLANET802.11g Wireless Access Point

Model: WAP-4000

Rev: 1.0 (August,2003)

Part No. EM-WAP4K

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION..................................................................................................1

1.1 PACKAGE CONTENTS .........................................................................................................1

1.2 SYSTEM REQUIREMENTS....................................................................................................1

1.3 FEATURES .........................................................................................................................1

1.4 SPECIFICATION ..................................................................................................................2

1.5 WIRELESS PERFORMANCE .................................................................................................3

CHAPTER 2 HARDWAREINSTALLATION.............................................................................4

CHAPTER 3 CONFIGURING THE WIRELESS ACCESS POINT............................................5

3.1 CONFIGURE THROUGHWEB BROWSER...............................................................................5

3.1.1Wizard......................................................................................................................6

3.1.2Status:......................................................................................................................8

3.1.3Basic Settings:..........................................................................................................9

3.1.4IPSettings:...............................................................................................................9

3.1.5 Advanced Settings:................................................................................................11

3.1.6Security:.................................................................................................................12

3.1.7802.1x.....................................................................................................................13

3.1.8 Tools:......................................................................................................................15

3.2 CONFIGURE THROUGH 54M APUTILITY............................................................................15

3.2.1Install 54MAPUtility...............................................................................................15

3.2.254MAPUtility configuration...................................................................................17

CHAPTER 4 802.1XAUTHENTICATION SETUP..................................................................23

4.1 802.1X INFRASTRUCTURE................................................................................................23

4.2 RADIUSSERVER SETUP.................................................................................................24

4.2.1Required Services..................................................................................................24

4.2.2Setup Procedure....................................................................................................24

4.3 AUTHENTICATOR SETUP ...................................................................................................38

4.4 WIRELESS CLIENT SETUP.................................................................................................39

4.4.1EAP-MD5 Authentication........................................................................................40

4.4.2EAP-TLSAuthentication.........................................................................................43

CHAPTER 5 APPLICATION....................................................................................................50

5.1 ACCESS POINTMODE.......................................................................................................50

5.2 WIRELESS APCLIENTMODE ............................................................................................50

5.3 WIRELESS BRIDGE MODE .................................................................................................51

5.4 MULTIPLE BRIDGE MODE ..................................................................................................51

CHAPTER 6 TROUBLESHOOTING.......................................................................................52

- 1 -

Chapter 1 Introduction

Thank you for purchasing WAP-4000. WAP-4000 is an IEEE 802.11g Wireless Access Point.IEEE

802.11g uses 2.4GHz frequency band,the same as IEEE 802.11b; but it provides more throughput rate

than 802.11b.The maximum throughput rate of 802.11g can up to 54Mbps. WAP-4000 is also backward

compatible and interoperable with IEEE 802.11b compliantwireless devices. Except for64/128bitWEP

encryption,WAP-4000 also integrates 802.1Xauthentication. Cooperating with aRADIUSservercan

make your wireless LAN more secure then ever.Provided with one reversed-polarity SMAmale

connector,WAP-4000 is easy to connect external antenna and booster to extend the wireless distance.

1.1 Package Contents

Make sure that you have the following items:

• One WAP-4000

• One AC Power Adapter

• One dipole antenna

• One User s Manual and Utility CD

• One Quick Installation Guide

Note:

If any of the above items are missing, contact your supplier as soon as

possible.

1.2 System Requirements

Before installation, please check the following requirementswith your equipment.

• Pentium Based (And Above) IBM-Compatible PC System

• CD-ROMdrive

• Windows 98/ME/2000/XP Operating System with TCP/IP protocol

1.3 Features

Wireless LAN IEEE802.11g and IEEE802.11b compliant

Strong network security with 802.1Xauthentication, and 64/128-bitWEP encryption.

One detachable reverse-polarity SMAconnectorscan connect to external antenna for expanding

connection distance

High speed data transfer rateup to 54Mbps

Four operation modes selectable: AP / AP Client / Point to Point /Point to Multipoint

Auto Fall-Back Data Rate forLong-Distance Communication and Noisy Environments

Features Roaming, BestAccess Point Selection, Load Balancing, and Network Traffic Filtering

Support63 clients to connectthe network. (Forbest performance, the suggested maximum clients

number of one WAP-4000 in AP mode is 25.)

Provide Windows-base configuration utility and Web Configuration

Support DHCPServer and Client

Support MAC Filter

- 2 -

1.4 Specification

Standard IEEE 802.11b, IEEE 802.11g

Signal Type DSSS (Direct Sequence Spread Spectrum)

Modulation BPSK / QPSK / CCK / OFDM

Port 10/100Base-TX(RJ-45) * 1

Antenna Detachable Dipole Antenna * 1

Antenna Connector Reversed Polarity SMAMale

Output Power 17dBm

802.11b

11 Mbps (CCK): -82dBm

5.5 Mbps (QPSK): - 86dBm

1, 2 Mbps (BPSK): - 90dBm

(typically @PER < 8% packet size 1024 and @25ºC + 5ºC)

Sensitivity

802.11g

54 Mbps: -72dBm

48 Mbps: - 72dBm

36 Mbps: -76dBm

24 Mbps: -79dBm

18 Mbps: -82dBm

12 Mbps: -86dBm

9 Mbps: -89dBm

6 Mbps: -90dBm

(typically @PER < 8% packet size 1024 and @25ºC + 5ºC)

Operating Mode AP,APClient, Bridge:Point to Point, Pointto MultiPoint

Security

64/128-bitWEP encryption

Password Protect

802.1Xsecurity (MD5 and TLS)

MAC Filtering

SSID BroadcastDisable function

Frequency Band 2.4 GHz ~2.484GHz

Channel FCC: 11 Channels (US, Canada)

ETSI: 13 Channels (Europe)

TELEC: 14 Channels (Japan)

802.11g Up to 54Mbps (6/9/12/18/24/36/48/54)

Data Rate 802.11b Up to 11Mbps (1/2/5.5/11)

Temperature 0~55°C

Operating Environment Humidity 5~95% (non-condensing)

LED Power: steady green

WLAN:green forwireless connectivity/activity

LAN: green for link, blink for activity

- 3 -

Input Power DC 5V, 2.5A

Certification FCC, CE

1.5 WirelessPerformance

The following information will help you utilizing the wireless performance, and operating coverage of

WAP-4000.

1. Site selection

To avoid interferences,please locate WAP-4000 and wireless clients away from transformers,

microwave ovens, heavy-duty motors, refrigerators, fluorescent lights, and other industrial

equipments.Keep the numberof walls, or ceilings between AP and clients as fewas possible;

otherwise the signal strength may be seriously reduced. Place WAP-4000 in open space or add

additional WAP-4000 as needed to improve the coverage.

2. Environmental factors

The wireless network is easily affected by many environmental factors. Every environment is

unique with different obstacles, construction materials, weather, etc. Itis hard to determine the

exact operating range of WAP-4000 in a specific location without testing.

3. Antenna adjustment

The bundled antenna of WAP-4000 is adjustable. Firstly install the antenna pointing straight up,

then smoothly adjust it if the radio signal strength is poor.But the signal reception is definitely weak

in some certain areas, such as location right down the antenna.

Moreover, the original antenna of WAP-4000 can be replaced with other external antennas to

extend the coverage.Please check the specification ofthe antenna you want to use, and make

sure it can be used on WAP-4000.

- 4 -

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the

WAP-4000.

1. Locate an optimum location for the WAP-4000. Thebestplace for your WAP-4000 is usually

at the center of your wireless network, with line of sight to all of your mobile stations.

2. Assemble the antennas to WAP-4000. Try to place them to aposition that can best cover your

wireless network. The antenna sposition will enhance the receiving sensitivity.

3. Connect RJ-45 cableto WAP-4000. Connect this WAP-4000 to your LAN switch/hub or a single

PC.

4. Plug in power adapter and connect topower source.After power on, WAP-4000 will start to

operate.

Note: ONLYuse the power adapter supplied with the WAP-4000. Otherwise, the product may be

damaged.

If you want to reset your WAP-4000

to default settings, press the Reset button 5 second.And

then wait for10 seconds for WAP-4000 to reboot.

- 5 -

Chapter 3 Configuring the Wireless Access Point

WAP-4000 can be configured via web browser or bundled utility. It is strongly recommended to configure

and manage WAP-4000 using a wired LAN computer.

3.1 Configurethrough Web Browser

Web configuration provides auser-friendly graphical user interface (web pages)to manage your

WAP-4000.An AP with an assigned IPaddress (e.g. http://192.168.1.1) will allowyou to monitorand

configure via web browser (e.g., MS Internet Explorer or Netscape).

1. Open your web browser.

2. Enter the IPaddress ofyour WAP-4000 in the address field (defaultIP address is http://192.168.1.1).

Please note that your PC sIP address should be on the same IPsubnet of the WAP-4000.For

example, you can configure your PC s IP address to 192.168.1.2 ifWAP-4000 is with IP 192.168.1.1.

3. AUser Name and Password dialog boxwill appear.Please enter your User Name and Password here.

DefaultUser Name and Password are both “admin”.Click Ok.

4. Then you will see the WAP-4000 web configuration page.

Otros manuales para 802.11g Wireless Access Point / Bridge...

Tabla de contenidos

Otros manuales de Enrutador de red de Planet

Planet

Planet FGSW-4840S Manual de usuario

Planet

Planet SW-502 Manual de usuario

Planet

Planet 85M Powerline to Ethernet Bridge with 4-Port Switch... Manual de usuario

Planet

Planet FNSW-1600S Manual de usuario

Planet

Planet VIP-280 Manual de usuario

Planet

Planet MAP-2100 Manual de usuario

Planet

Planet ADSL 2/2+ VoIP Router IAD-200W Manual de usuario

Planet

Planet ADSL 2/2+ VPN Firewall Router ADE-4300A/B Manual de usuario

Planet

Planet XRT-101A Manual de usuario

Planet

Planet XRT-401B Manual de usuario

Planet

Planet IGS-5227-6T Manual de usuario

Planet

Planet GS-4210-24P2S Manual de usuario

Planet

Planet G.SHDSL.bis Bridge Router GRT-504 Manual de usuario

Planet

Planet ADE-3400 Manual de usuario

Planet

Planet G.SHDSL.bis Bridge Router GRT-504 Manual de usuario

Planet

Planet ISW-500T Manual de usuario

Planet

Planet GSW-1600HP Manual de usuario

Planet

Planet FNSW-2400PS Manual de usuario

Planet

Planet ADE-3400 Manual de usuario

Planet

Planet ADE-3400v4 Manual de usuario

Planet

Planet ADN-4101 Manual de usuario

Planet

Planet ADSL Firewall Router ADE-4120 Manual de usuario

Planet

Planet WGR-500-4P Manual de usuario

Planet

Planet ADSL 2/2+ VPN Firewall Router ADE-4300A/B Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad