Planet ISW-802M Manual de usuario

6-Port 10/100Mbps TP + 2-Port 100Base-FX

Managed Industrial Ethernet Switch

ISW-802M

User's Manual

Trademarks

cPLANET Technology Corp. 2006.

Contents subject to which revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their

respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and

applications, and makes no warranty and representation, either implied or expressed, with respect to the

quality, performance, merchantability, or fitness for a particular purpose.

PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability

for any inaccuracies or omissions that may have occurred.

Information in this User's Manual is subject to change without notice and does not represent a

commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be

contained in this User's Manual. PLANET makes no commitment to update or keep current the

information in this User's Manual, and reserves the right to make improvements to this User's Manual

and/or to the products described in this User's Manual, at any time without notice.

If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate

your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

Instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at whose own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which

case the user may be required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the

presence of hazardous substances in electrical and electronic equipment, end users

of electrical and electronic equipment should understand the meaning of the

crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal

waste and have to collect such WEEE separately.

Revision

PLANET Managed Industrial Ethernet Switch User's Manual

FOR MODELS: ISW-802M

Part No. EM_ISW802Mv1 (2081-AH0010-000)

Table of Contents

1. INTRODUCTION................................................................................................................... 5

1.1 Packet Contents.............................................................................................................. 5

1.2 How to Use This Manual ................................................................................................. 5

1.3 Product Feature............................................................................................................... 5

1.4 Product Specification....................................................................................................... 6

2. HARDWARE INSTALLATION .............................................................................................. 9

2.1 Product Description......................................................................................................... 9

2.2 Mounting Installation ..................................................................................................... 14

3. NETWORK INSTALLATION............................................................................................... 17

3.1 Hardware Installation..................................................................................................... 17

3.2 Network Application....................................................................................................... 17

3.3 Redundant Ring Application.......................................................................................... 18

3.4 Coulping Ring Application ............................................................................................. 19

3.5 Dual Homing Application ............................................................................................... 20

4. WEB MANAGEMENT......................................................................................................... 21

4.1 About Web-based Management.................................................................................... 21

4.2 Preparing for Web Management ................................................................................... 21

4.3 System Login................................................................................................................. 21

4.4 Port Status..................................................................................................................... 22

4.5 Single port information .................................................................................................. 23

4.6 Port Statistics................................................................................................................. 24

4.7 Port Control ................................................................................................................... 24

4.8 Switch Settings.............................................................................................................. 25

4.9 Port Mirroring................................................................................................................. 26

4.10 VLAN configuration ..................................................................................................... 27

4.11 Alert.............................................................................................................................. 33

4.12 IP Configuration........................................................................................................... 36

4.13 SNTP Configuration .................................................................................................... 37

4.14 IP Security ................................................................................................................... 39

4.15 RSTP Configuration .................................................................................................... 40

4.16 Redundant Ring .......................................................................................................... 42

4.17 QoS Configuration....................................................................................................... 44

4.18 IGMP ........................................................................................................................... 46

4.19 SNMP Configuration.................................................................................................... 47

4.20 Security Manager ........................................................................................................ 49

4.21 Configuration Backup.................................................................................................. 50

4.22 Factory Default............................................................................................................ 52

4.23 Save Configuration...................................................................................................... 53

4.24 System Reboot............................................................................................................ 54

4.25 Rate Control ................................................................................................................ 54

4.26 System Log ................................................................................................................. 55

5. TROUBLESHOOTING........................................................................................................ 58

5.1 Incorrect connections .................................................................................................... 58

5.2 Diagnosing LED Indicators............................................................................................ 58

6. APPENDIX .......................................................................................................................... 60

6.1 100BASE-TX/10BASE-T Pin Assignments ................................................................... 60

1. INTRODUCTION

The 6-Port 10/100TX plus 2-Port 100FX with redundant ring managed industrial switch is a cost-effective

solution and meets the high reliability requirements demanded by industrial applications. The switch can

be easily managed through the Web GUI. By using fiber port can extend the connection distance that

increases the network elasticity and performance. It also provides the redundant ring function that can

prevent the network connection failure.

1.1 Packet Contents

Check the contents of your package for following parts:

▫Industrial Fast Ethernet Switch x1

▫DIN-Rail kit (screwed on the switch)

▫Wall-mount kit (wall-mount plate with 6 screws)

▫CD-ROM user's manual x1

If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the

carton including the original packing material, and use them against to repack the product in case there is

a need to return it to us for repair.

1.2 How to Use This Manual

This User Manual is structured as follows:

Chapter 2, HARDWARE INSTALLATION

The chapter explains the functions of the Switch and how to physically install the Switch.

Chapter 3, NETWORK INSTALLATION

The chapter explains how to install the Switch in the Network.

Chapter 4, WEB MANAGEMENT

The chapter explains how to configure the switch by the web interface.

Chapter 5, TROUBLE SHOOTING

The chapter explains how to trouble shooting of the Switch.

Chapter 6, APPENDIX

The chapter contains cable information of the Switch.

1.3 Product Feature

Hardware Feature

▫Comply with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX/1000Base-FX

▫6-Port 10/100Mbps TP + 2-Port 100Mbps Fiber interfaces

▫CSMA/CD Protocol

▫RJ-45 Port support auto MDI/MDI-X function

▫2K MAC address table

▫1Mbit memory buffer

▫2.0Gbps back-plane

▫Wide-range redundant power design

▫Store and forward switch architecture

▫DIN rail and 3-way wall mount design

Industrial Conformance

▫12~48V DC, redundant power input with polarity reverse protect function

▫0 to 60 Degree C operation temperature

▫IP-30 Aluminum case

▫Relay alarm for port breakdown and power failure

▫FCC Class A, CE compatibility

▫Free fall, Shock and Vibration Stability

Switching Feature

▫Ring function data redundant, 300ms data recovery

▫802.1q Tagged VLAN/Port-based VLAN

▫IEEE 802.1p class of service, 4 priority queues

▫IGMP v1 and Query mode

▫802.1d STP/802.1w Rapid STP

▫Ingress/Egress bandwidth control

System

▫Web/SNMP management

▫System event log support

▫Configuration backup/restore

▫E-mail event alert

▫IP security for illegal access prevention

▫TFTP firmware upgrade

▫Port mirror transmission monitoring

1.4 Product Specification

Model ISW-802M

Hardware

Standard IEEE 802.3af, IEEE 802.3, IEEE802.3u, 10/100Base-TX

10/100Mbps TP 6

100Base-FX 2 (mm, sc)

Protocol CSMA/CD

Switching Architecture Store and forward

Transfer Rate 144,880 pps for Ethernet port and 1448,800 pps for Fast Ethernet port

MAC address 2K

Memory Buffer 1Mbit

Network Cable 10Base-T : 2-pair UTP/STP Cat 3, 4, 5 cable

100Base-TX: 2-pair UTP/STP Cat. 5 cable

10Base-T: EIA/TIA-568 100-ohm (100m)

Optical Cable SC (Multi-mode): 50/125µm to 62.5/125µm

Available distance: 2KM, Wavelength: 1310nm

LED Per port: Link/Activity (Green), Full duplex/Collision (Yellow)

Per unit: Power (Green), Power 1 (Green), Power 2 (Green), Fault (Yellow),

Ring Master (Green)

Back-plane 1.6Gbps

Packet throughput ability 1.19Mpps@64bytes

Power Supply 12 to 48 V DC, Redundant power with polarity reverse protection function

Power Consumption 4.6 Watts

Installation Provide DIN rail kit and wall mount plate for 3-way installation

Operating environment 0 to 60 Degree C, 5% to 90%RH (Non-condensing)

Storage environment -40 to 85 Degree C, 5% to 90%RH (Non-condensing)

Dimension (W x D x H) 54 × 105 × 155 mm

Emission FCC Class A, CE mark

Stability testing IEC60068-2-32(Free fall), IEC60068-2-27(Shock), IEC60068-2-6(Vibration)

Management

Management Interface Web, SNMP v1,v2c, v3

SNMP MIB RFC 1213 MIBII, RFC 1493 Bridge MIB, RMON RFC 1757, RFC 2674

VLAN MIB, RFC 1643 Ethernet like MIB, RFC1215 Trap MIB, IGMP MIB.

Private MIB for switch information, super ring, port alarm, TFTP firmware

upgrade, reset, port mirror, IP security.

SNMP Trap Up to 3 Trap stations.

Cold start, Port link Up, Port link down, Authentication Failure, Private Trap

for power status, Port Alarm configuration, Fault alarm, super ring.

Management IP security Support IP address security to prevent unauthorized intruder.

Firmware update Support TFTP firmware update, TFTP configuration backup and restore.

System event log Provides 1000 event log entries.

Alarm Provides one relay output for port breakdown, power fail and provide DIP

switch to mask link down port.

Alarm Relay current carry ability: 1A @ DC24V

DHCP client Provide DHCP client function to obtain IP address from DHCP serve.

Switching

Redundant ring 2 ports for super ring to provide redundant backup feature and the recovery

time below 300ms. It also supports coupling ring function. Ring and coupling

port configure by web interface and ringmaster by hardware DIP switch.

VLAN Supports port-based VLAN and IEEE802.1Q Tag VLAN.

Both of port based and Tag based VLAN group up to 64 VLANs.

Class of service IEEE802.1p class of service support, per port provides 4 priority queues.

Quality of service The quality of service support port based, Tag based and IPv4 Type of

service.

IGMP Support IGMP v1 and Query mode. Up to 256 groups.

Spanning tree IEEE802.1d spanning tree and IEEE802.1w rapid spanning tree.

SNTP Support simple network time protocol.

SMTP Support simple mail transfer protocol.

Bandwidth control Support ingress packet filter and egress packet limit.

The egress rate control supports all of packet type and the limit rates are

128kbps, 256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB.

Ingress filter packet type combination rules are

Broadcast/Multicast/Unknown Unicast packet, Broadcast/Multicast packet,

Broadcast packet only and all of packet. The packet filter rate can be set

follow as:1Mbps、2Mbps、4Mbps、8Mbps、16Mbps、32Mbps、64Mbps.

Port mirror Support TX packet only or both of TX and RX packet.

Packet filter 4 selection rules for different type of packet combination:

1. All of packet

2. Broadcast/ multicast/ unknown unicast packet

3. Broadcast/ multicast packet

4. Broadcast packet only

Network Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE802.3x Flow Control and Back-pressure

IEEE802.1d spanning tree / IEEE802.1w rapid spanning tree

IEEE802.1p class of service

IEEE802.1Q VLAN Tag

2. HARDWARE INSTALLATION

This section describes the functionalities of the Switch's components and guides how to install it on the

rack or mount to the wall. Basic knowledge of networking is assumed. Please read this chapter

completely before continuing.

2.1 Product Description

The PLANET Managed Industrial Ethernet Switch provides substation hardened, fully managed, Ethernet

switches specifically designed to operate reliably in electrically and environmentally harsh environments.

It provides IEEE 1613 Class 2 error-free communications performance under EMI stress. An operating

temperature range of 0 to 60 Degree C allows the switch be placed in almost any location. The Switch

also provides a wide range of power supply options suitable for multiple industries and for worldwide

operability.

2.1.1 Product Overview

The management switch models offer advanced Layer 2 networking features and network management

via the Web interface. The feature of the switching is the performance of its IEEE 802.1w Rapid Spanning

Tree Protocol (RSTP) used for implementing fault tolerant ring and mesh network architectures. The

protocol has been optimized to support ring and fault recovery times in the order of less than 300ms.

The management function provides improved system reliability and advanced networking features

making it ideally suited for creating Ethernet networks for mission-critical, real-time, control applications.

2.1.2 Switch Front Panel

Figure 2-1 shows the front panel of the switch.

Figure 2-1 ISW-802M Front Panel

2.1.3 LED Indications

LED Status Meaning

Green The switch unit is power on.

Power

Off The switch unit is no power input.

Green Power on

Power 1

Off No power inputs

Green Power on

Power 2

Off No power inputs

Yellow Power failure or UTP port failure or Fiber port failure

Fault

Off No Power failure or UTP port failure or Fiber port failure occurs

Green The industrial switch is the master of redundant ring group.

R. M.

(Ring Master) Off The industrial switch is not a ring master in redundant ring group.

Green The port is linking.

LNK/ACT

(Port 7 & 8) Blinks The port is transmitting or receiving packets from the TX device.

Tabla de contenidos

Otros manuales de Enrutador de red de Planet

Planet

Planet MGSW-28240F Manual de usuario

Planet

Planet WNAP-7200 Manual de usuario

Planet

Planet SG-4800 Manual de usuario

Planet

Planet FNSW-2400PS Manual de usuario

Planet

Planet ADN-4100 Manual de usuario

Planet

Planet ERT-805 Manual de usuario

Planet

Planet IGS-5225-16T4S Manual de usuario

Planet

Planet VR-100 Series Manual de usuario

Planet

Planet Gaw9.2Z18-4 Manual de usuario

Planet

Planet ADSL 2/2+ Router with USB Port ADE-3410v2 Manual de usuario

Planet

Planet WGSW-404 Manual de usuario

Planet

Planet IGS-801M Manual de usuario

Planet

Planet WRT-403 Manual de usuario

Planet

Planet GRT-402 Manual de usuario

Planet

Planet VC-234G Manual de usuario

Planet

Planet IAD-200 Manual de usuario

Planet

Planet GSW-1600S Manual de usuario

Planet

Planet WGR-500 Manual del operador

Planet

Planet GSW-1602SF Manual de usuario

Planet

Planet WDAP-C7210E Manual de usuario

Planet

Planet ADE-3410 Manual de usuario

Planet

Planet XRT-401F Manual de usuario

Planet

Planet FGSD-1022VHP Manual de usuario

Planet

Planet GSW-1602SF Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad