Planet Networking & Communication XGS3-24042 Manual de usuario

24-Port Gigabit TP/SFP + 4-Port 10G SFP+ Slot

Layer 3 Stackable Managed Switch

XGS3-24042 & XGS3-24242

Quick Installation Guide

Table of Contents

1. Package Contents ....................................................................................... 3

2. Switch Management.................................................................................... 4

3. Requirements ............................................................................................. 5

4. Terminal Setup ........................................................................................... 6

5. Logon to the Console .................................................................................. 8

6. ConguringIPAddress................................................................................ 9

7. Setting1000BASE-XforSFP+Port..............................................................10

8. Setting100BASE-FXforSFPPort ................................................................10

9. UsingCopperInterfaceonComboPort ........................................................11

10.SavingtheConguration ...........................................................................11

11.StartingWebManagement.........................................................................12

12.LoggingintotheManagedSwitch..............................................................13

13.SavingCongurationviatheWeb...............................................................14

14.RecoveringBacktoDefaultConguration ....................................................15

15. Customer Support.....................................................................................16

1. Package Contents

ThankyouforpurchasingPLANET24-PortGigabitTP/SFP+4-Port10GSFP+Layer

3StackableManagedSwitch.Thedescriptionofthismodelisshownbelow:

XGS3-24042 Layer 3 24-Port 10/100/1000T + 4-Port 10G SFP+ Stack-

ableManagedSwitch

XGS3-24242 Layer 3 24-Port 100/1000X SFP with 16-Port shared TP +

4-Port10GSFP+StackableManagedSwitch

“Managed Switch” is used as an alternative name in this Quick Installation

Guide.

Open the box of the Managed Switch and carefully unpack it. The box should

containthefollowingitems

TheManagedSwitchx1

QuickInstallationGuidex1

RJ45-to-DB9ConsoleCablex1

PowerCordx1

RubberFeetx4

TwoRack-mountingBracketswithAttachmentScrewsx1

SFPDustCapx8(XGS3-24042)

SFPDustCapx28(XGS3-24242)

QSFP+DustCapx2(XGS3-24242)

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. Switch Management

To set up the Managed Switch, the user needs to congure the Managed Switch

fornetwork management.The ManagedSwitchprovides twomanagement options:

Out-of-Band ManagementandIn-Band Management.

Out-of-Band Management

Out-of-band management is the management through Console interface.

Generally, the user will use out-of-band management for the initial switch

conguration,orwhenin-bandmanagementisnotavailable.

In-Band Management

In-band management refers to the management by logging in to the Managed

Switchusing Telnetor HTTP,orusingSNMP managementsoftwareto congurethe

Managed Switch. In-band management enables the management of the Managed

SwitchtoattachsomedevicestotheSwitch.Thefollowingproceduresarerequired

toenablein-bandmanagement:

1. Logon to console

2.Assign/CongureIPaddress

3. Create a remote login account

4.EnableHTTPorTelnetserverontheManagedSwitch

In case in-band management fails due to Managed Switch conguration changes,

out-of-band management can be used for conguring and managing the Managed

Switch.

3. Requirements

Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,

Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.

WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)

Serial Port Connection(Terminal)

 The above Workstations come with COM Port (DB9) or USB-to-RS232

converter.

 The above Workstations have been installed with terminal emulator, such as

Tera Term or PuTTY.

 Serial cable -- one end is attached to the RS232 serial port, while the other

endtotheconsoleportoftheManagedSwitch.

Ethernet Port Connection

 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.

 The above PC is installed with Web browser and JAVA runtime environment

plug-in.

Note

It is recommended to use Internet Explore 8.0 or above to access

the Managed Switch. If the Web interface of the Managed Switch

is not accessible, please turn off the anti-virus software or firewall

andthentryitagain.

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or

notebook computer and to serial (console) port of the Managed Switch. The

console port of the Managed Switch is DCE already, so that you can connect the

consoleportdirectlythroughPCwithouttheneedofNullModem.

Managed Switch

PC / Workstation

with

Terminal Emulation Software

Serial Port

RS232 to RJ45 Cable

Console Port

RJ45

Figure 4-1 Managed Switch Console Connectivity

A terminal program is required to make the software connection to the Managed

Switch. Tera Term program may be a good choice. The Tera Term can be accessed

fromtheStart menu.

1. Click STARTmenu,thenPrograms,andthenTera Term.

2.When the following screen appears, make sure that the COM port should be

conguredas:

Figure 4-2 Tera Term COM Port Conguration

XGS3-24042 XGS3-24242

Baud:115200 Baud:9600

Parity:None Parity:None

Databits:8 Databits:8

Stopbits:1 Stopbits:1

Flowcontrol:None Flowcontrol:None

5. Logon to the Console

Once the terminal is connected to the device, power on the Managed Switch, and

theterminalwilldisplay“runningtestingprocedures”.

Then, the following message asks for the login user name and password. The

factory default user name and password are as follows as the login screen in

Figure5-1appears.

Username:admin

Password:admin

Figure 5-1 Managed Switch Console Login Screen

The user can now enter commands to manage the Switch. For a detailed

descriptionofthecommands,pleaserefertothefollowingchapters.

Note

1.Forsecurityreason,pleasechangeandmemorizethenewpass-

wordafterthisfirstsetup.

2.Only accept command in lowercase letter under console inter-

face.

6.ConguringIPAddress

The IP address conguration commands for VLAN1 interface are listed below. The

congurationcommandsareasfollows:

XGS3-24042# cong

XGS3-24042(cong)# interface vlan 1

XGS3-24042(cong-if-Vlan1)# ip address 192.168.1.254 255.255.255.0

ThepreviouscommandwouldapplythefollowsettingsfortheManagedSwitch.

IPv4 Address: 192.168.1.254

Subnet Mask: 255.255.255.0

Figure 6-1 Conguring IPv4 Address Screen

To check the current IP address or modify a new IP address for the Managed

Switch,pleaseusetheprocedureasfollows:

Show the current IP address

1. On “XGS3-24042#”prompt,enter“show ip interface brief”.

2.The screen displays the current IP address, subnet mask and gateway as shown

inFigure6-2.

Figure 6-2 Showing IP Information Screen

If the IP is successfully congured, the Managed Switch will apply the new IP

address setting immediately. You can access the Web interface of Managed Switch

throughthenewIPaddress.

Note

If you are not familiar with console command or the related

parameter, enter “help” anytime in console to get the help

description.

7.Setting1000BASE-XforSFP+Port

The Managed Switch supports both 10GBASE-X SFP+ transceiver and

1000BASE-X SFP transceiver by manual setting and the default SFP+ port

speed is set to 10Gbps. To establish the ber connection with 1000BASE-X SFP

transceiver,thefollowingcommandcongurationisrequired:

XGS3-24042#cong

XGS3-24042(cong)#interface ethernet 1/0/25-28

XGS3-24042(cong-if-port-range)#speed-duplex force1g-full

Figure 7-1 Setting 1000BASE-X Screen

8.Setting100BASE-FXforSFPPort

The Managed Switch supports both 1000BASE-X and 100BASE-FX SFP

transceivers by manual setting and the default SFP port speed is set to1000Mbps.

To establish the ber connection with 100BASE-FX SFP transceiver, the following

commandcongurationisrequired:

XGS3-24042#cong

XGS3-24042(cong)#interface ethernet 1/0/21-24

XGS3-24042(cong-if-port-range)#speed-duplex force100-fx

Figure 8-1 Setting 100BASE-FX Screen

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Planet Networking & Communication