Planet Networking & Communication Wgsw-28040 Manual de usuario

28-Port 10/100/1000Mbps with

4 Shared SFP Managed Gigabit Switch

WGSW-28040 / WGSW-28040P

Quick Installation Guide

Table of Contents

1. Package Content.......................................................................................... 3

2. Requirements .............................................................................................. 4

3. Terminal Setup ............................................................................................ 5

4. Logon to the Console ................................................................................... 6

5. Congure IP Address ................................................................................... 7

6. Save the Conguration................................................................................. 9

7. Start Web Management...............................................................................10

Customer Support...........................................................................................14

1. Package Content

Thank you for purchasing PLANET Layer 2 Managed Switch, WGSW-28040 series.

Terms of “Managed Switch” means the Switches mentioned titled in the cover

page of this Quick installation guide, i.e. WGSW-28040 / WGSW-28040P.

Open the box of the Managed Switch and carefully unpack it. The box should

contain the following items:

The Managed Switch x 1l

User’s Manual CD x 1l

Quick Installation Guide x 1l

RS232 Cable x 1l

Rubber Feet x 4l

Two Rack-mounting Brackets with Attachment Screws x 1l

Power Cord x 1 l

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. Requirements

Workstations of subscribers running Windows XP/2003/Vista/7/2008, MAC OS9 l

or later, Linux, UNIX or other platform compatible with TCP/IP protocols.

Workstation installed with Ethernet NIC (Network Interface Card)l

Serial Port connectl (Terminal)

 Above PC with COM Port (DB9)

Ethernet Port connectl

 Network cables - Use standard network (UTP) cables with RJ-45 connectors.

 Above PC installed with Web Browser and JAVA runtime environment Plug-in

Note

It is recommended to use Internet Explore 7.0 or above to access

WGSW Managed Switch.

3. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or

notebook computer and to serial (console) port of the WGSW Managed Switch. The

console port of the Managed Switch is DCE already, so that you can connect the

console port directly through PC without the need of Null Modem.

PC / Workstation

with

Terminal emulation software

RS-232

Serial Port

115200,8,n,1

WGSW Managed Switch

Note

In the terminal setup steps below, this Quick Installation Guide

use WGSW-28040 as the example. However, the steps for WGSW-

28040P are similar.

A terminal program is required to make the software connection to the WGSW

Managed Switch. Windows’ Hyper Terminal program may be a good choice. The

Hyper Terminal can be accessed from the Start menu.

1. Click START, then Programs, Accessories and then Hyper Terminal.

2. When the following screen appears, make sure that the COM port should be

congured as:

 Baud: 115200

 Data bits: 8

 Parity: None

 Stop bits: 1

 Flow Control: None

4. Logon to the Console

Once the terminal has connected to the device, power on the WGSW Managed

Switch, the terminal will display that it is running testing procedures.

Then, the following message asks the login username and password. The factory

default username and password as following and the login screen in Figure 4-1

appears.

Username: admin

Password: admin

1. On “Username” & “Password” prompt, enter “admin”.

2. On “WGSW-28040>” prompt, enter “enable”.

3. On “Username” & “Password” prompt, enter “admin”.

Figure 4-1: WGSW Managed Switch Console Login screen

Note

1. For security reason, please change and memorize the new pass-

word after this first setup.

2. Only accept command in lowercase letter under console inter-

face.

5. Congure IP Address

The WGSW Managed Switch is shipped with default IP address as following.

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

To check the current IP address or modify a new IP address for the Switch, please

use the procedures as follow:

Show the current IP address

1. On "WGSW-28040#” prompt, enter “cong”.

2. On "WGSW-28040 (cong)#” prompt, enter “show ip”.

3. The screen displays the current IP address, Subnet Mask and Gateway. As show

in Figure 5-1.

Figure 5-1: Show IP Information screen

 Congure IP address

4. On “WGSW-28040(cong)#” prompt, enter the following command and press

<Enter>. As show in Figure 5-2.

WGSW-28040(cong)# ip address 192.168.1.100 255.255.255.0

WGSW-28040(cong)# ip default-gateway 192.168.1.254

The previous command would apply the follow settings for the Switch.

IP Address: 192.168.1.100

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.254

Figure 5-2: Set IP Address screen

5. Repeat Step 1 to check if the IP address is changed.

If the IP is successfully congured, the WGSW Managed Switch will apply the

new IP address setting immediately. You can access the Web interface of WGSW

Managed Switch through the new IP address.

Note

If you do not familiar with console command or the related param-

eter, enter “?” anytime in console to get the help description.

6. Save the Conguration

In switch, the running conguration le stores in the RAM. In the current version,

the running conguration sequence running-cong can be saved from the RAM to

FLASH by write command or copy running-cong startup-cong command, so

that the running conguration sequence becomes the start up conguration le,

which is called conguration save.

1. On “WGSW-28040(cong)#” prompt, enter “copy running-cong startup-

cong”. As show in Figure 6-1.

Figure 6-1: Save the Conguration screen

7. Start Web Management

The following shows how to start up the Web Management of the WGSW

Managed Switch. Note the WGSW Managed Switch is congured through an

Ethernet connection, please make sure the manager PC must be set on the same

IP subnet address.

For example, the default IP address of the WGSW Managed Switch is

192.168.0.100, then the manager PC should be set at 192.168.0.x (where x

is a number between 1 and 254, except 100), and the default subnet mask is

255.255.255.0.

WGSW Managed Switch

RJ-45/UTP-Cable

PC / Workstation

with

IE Browser

IP Address:

192.168.0.x

IP Address:

192.168.0.100

Figure 7-1: IP Management Diagram

Otros manuales para wgsw-28040

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Planet Networking & Communication