Pickering Pxi 41-750 Manual de usuario

Page (1)

BATTERY SIMULATOR MODULE 41-750

pickering

Issue 7.1 June 2017

User Manual

Battery Simulator Module

(Model No. 41-750)

pickeringtest.com pickering

Page (II) BATTERY SIMULATOR MODULE 41-750

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

BATTERY SIMULATOR MODULE 41-750

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) BATTERY SIMULATOR MODULE 41-750

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

BATTERY SIMULATOR MODULE 41-750

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Guidance on Using the Module............................................2.2

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Soft Front Panel Installation.................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options For Pickering PXI Cards.................4.1

Programming The Module ...................................................4.3

Module Architecture..............................................................4.3

Using The Soft Front Panel ..................................................4.9

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting.........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Calibration Procedure...........................................................7.2

Test Procedure.......................................................................7.3

Test Results ...........................................................................7.5

Alignment Procedure ............................................................7.7

Alignment Test Record..........................................................7.8

CONTENTS

Page (VI) BATTERY SIMULATOR MODULE 41-750

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

BATTERY SIMULATOR MODULE 41-750

pickering

Page (VII)

REED RELAY MODULE 40-110/115/120/125

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the PXI/LXI chassis are populated with blanking plates to prevent access to user

I/O signals that may be present. Blanking panels are available to order from Pickering in a variety

of slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page (VIII) BATTERY SIMULATOR MODULE 41-750

pickering

THIS PAGE INTENTIONALLY BLANK

Page 1.1

BATTERY SIMULATOR MODULE 41-750

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

41-750

Battery Simulator Module

●Single Slot Battery Simulator

●Remote Voltage Sense

●Isolated Outputs

●Output Voltage Up To 6V

●Power Supplied From PXI Backplane

●Pickering Interfaces Monitor System For

Current and Voltage

●Programmable Current Sink Capability To

0.5A For Charger Load Simulation

●VISA and Kernel Drivers

●Supported by PXI or LXI Chassis

●2 Year Warranty

The 41-750 is a battery simulator module that can be

used to simulate the power supplies of cellular phones

and other portable battery devices. It features fully

ﬂoating output terminals that can deliver voltages up to

6 Volts. The fast responding remote sense connections

allow the module to regulate the supply voltage at

the device under test. The output terminals can ﬂoat

±50V relative to the front panel ground to ensure the

accurate simulation of battery operation.

A module can source or sink current to provide

simulation of a battery supply or a battery under

charge. The use of two modules allows the simulation

of both the charger voltage source and the battery.

The programmable current sink can be set to divert

up to 0.5A of the load current, permitting the battery

simulator to act as a net current sink when connected

to a charger circuit. The 41-750 is capable of delivering

up to 2.8 Amps into the load.

The module derives its power from the PXI backplane

and requires no external power source.

The battery simulator can be conﬁgured to prevent

misleading operation. If the remote sense lines are

not connected to the device under test, the power

supply is automatically closed down. The alternative

conﬁguration regulates the front panel voltage if the

sense lines are not connected to the load.

Monitoring of the output voltage and current is

provided through the simple to connect Pickering

Interfaces Monitor facility. A single DMM can be used

to report voltages and currents on multiple modules,

through an easily implemented daisy chain connection.

This facility can also be used to monitor other types of

modules in the Pickering range. The wide bandwidth

of the monitor facility allows the use of external data

acquisition devices to capture voltage and current

variations with time.

BATTERY SIMULATOR

41-750

41-750 PCB View

ISSUE 8.5 JUN 2017

Soft Front Panel for Battery Simulator Modules

OBSOLETE PRODUCT

Page 1.2 BATTERY SIMULATOR MODULE 41-750

pickering

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

Power Requirements from PXI Power Supply

+3.3V +5V +12V -12V

0.1A 6A Maximum 0.1A 0.1A

Speciﬁcation

Number of Channels: 1 (isolated)

Output Voltage Range:

0 to 6 Volts (at front panel), isolated

±50V maximum common mode

voltage.

Voltage Resolution: Set with 16 bit resolution.

Voltage Sense: Remote sensing of load voltage,

mechanically conﬁgurable to either

regulate front panel voltage or close

down if not connected.

Output Current: Up to 2.8 Amps (includes set sink

current).

Current Sink: Programmable current sink from

0 to 0.5 Amps available for output

voltages above 0.5V.

Current sink setting reduces the

available maximum output current

delivered to the load if an external

current source is not applied.

Load Response Time: 15µs (1A to 2A, 1m connection wire,

using all connection pins).

Power Source: PXI backplane +5V.

Monitor: Provided through monitor port

to measure output voltages and

currents. Can be used to measure

load voltage, front panel voltage,

load current and sink current.

Currents are measured by voltage

sensing across a resistor.

Monitor Accuracy: Voltage DMM ±30µV

Current 1% ±1mA (after zero

correction).

Protection: Short circuit protection.

Thermal protection.

Operation of protection is reported.

Prolonged operation of protection is

not recommended to avoid chassis

connector damage.

Output Connector: 25-pin male D-type. Each connection

is supported by two pins to permit

doubling up of connections.

PXI Characteristics

Backplane connection: 33MHz, 32 bit.

Mechanical: 3U, 1 slot.

Typical load transient response of 41-750 for 6V output

when load is changed abruptly from 1A to 2A in <<1µs

Product Order Codes

Battery Simulator 2.8 Amps 41-750-001

OBSOLETE PRODUCT

Mating Connectors & Cabling

For connection accessories for the 41-750 module please

refer to the 90-008D 25-pin D-type Connector Accessories

data sheet where a complete list and documentation can be

found for accessories.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Pickering

Pickering

Pickering 4x-727A Manual de usuario

Pickering

Pickering 40-528A Manual de usuario

Pickering

Pickering 40-582 Manual de usuario

Pickering

Pickering PXI 40-785 Manual de usuario

Pickering

Pickering PXI BRIC 40-562A Manual de usuario

Pickering

Pickering PXI 40-145 Manual de usuario

Pickering

Pickering 40-785C Manual de usuario

Pickering

Pickering BRIC 40-565B Manual de usuario

Pickering

Pickering 40-519A Manual de usuario

Pickering

Pickering 40-584 Manual de usuario

Pickering

Pickering PXI BRIC 40-569 Manual de usuario

Pickering

Pickering 41-765 Manual de usuario

Pickering

Pickering PXI BRIC 40-563A Manual de usuario

Pickering

Pickering 40-297A Manual de usuario

Pickering

Pickering 43-182B Manual de usuario

Pickering

Pickering 40-519B Manual de usuario

Pickering

Pickering 40-540 Manual de usuario

Pickering

Pickering 40-884 Manual de usuario

Pickering

Pickering PXI 40-597 Manual de usuario

Pickering

Pickering 40-262 Manual de usuario

Pickering

Pickering PXi 41-720 Manual de usuario

Pickering

Pickering 40-534 Manual de usuario

Pickering

Pickering 40-521 Manual de usuario

Pickering

Pickering 40-870 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario