Philips LP600STU Manual de usuario

Ni - Cd

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

A Division of Philips Electronics North America Corporation

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine

70126200

UNIVERSAL INPUT, SELF-TESTING EMERGENCY LIGHTING EQUIPMENT

Installation Instructions

1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter

connector must be open. Do not join inverter connector until installation is complete and AC power is

supplied to the emergency ballast.

2. This product is for use with most 14 W through 54 W (2' - 4') T5 bipin, 22 W through 40 W T5 circular,

36 W through 55 W (4-pin) long compact, and 17 W through 55 W (2' - 5') T8 bipin ﬂuorescent lamps.

3. Make sure all connections are in accordance with the National Electrical Code, Canadian Electrical Code and

any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and

inverter connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or ﬁeld installation in either the ballast channel or on top of the

ﬁxture.

6. This product is suitable for damp locations where the ambient temperature is 0°C minimum, +50°C

maximum. Product is also suitable for installation in sealed and gasketed ﬁxtures. Product is not suitable

for heated air outlets and wet or hazardous locations.

7. An unswitched AC power source is required. (120 through 277 VAC, 50 or 60Hz)

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not

ﬁeld replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

LP600STU

04/16/11

Fixture

Test Button

Hex Nut

Test Switch

Leads

Push to Test

STEP #1

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW

OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN

INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED TO

THE EMERGENCY BALLAST.

STEP #2 INSTALLING THE TEST SWITCH

> Refer to Illustration 2 and install the test

switch through the ballast channel cover of a

troffer or through the side of a strip ﬁxture.

> Drill a 1/2" hole and install the switch as

shown.

> Refer to the wiring diagrams on the

following pages and wire the test switch

so that it removes AC power from both the

emergency ballast and the AC ballast at the

same time.

NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched source of

power is required. The emergency ballast must be fed from the same branch circuit as

the AC ballast.

ILLUSTRATION 1

STEP #3 INSTALLING THE CHARGING

INDICATOR LIGHT

> Refer to Illustration 3A or 3B and install the

charging indicator light so that it will be

visible after the ﬁxture is installed.

INSTALLATION

ILLUSTRATION 2

STEP #4 WIRING THE EMERGENCY BALLAST

> Determine the type of AC ballast installed in the ﬁxture.

> Select the appropriate wiring diagram and connect the emergency ballast to the AC ballast and lamp(s). Make

electrical connections in accordance with the National Electrical Code, Canadian Electrical Code and any local

regulations.

> To disable audible alarm, cut red/white wire loop. CAP ENDS.

> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.

It is normal for the indicator light to remain off for a few minutes on initial start-up, as the battery voltage rises

to normal range. Refer to Troubleshooting Guide if this condition persists. The inverter connector MUST be joined

for the AC ballast to operate normally.

> At this point, power should be connected to both the AC ballast and the emergency ballast, and the Charging

Indicator Light should illuminate indicating the battery is charging.

> A short-term discharge test may be conducted after the emergency ballast has been charging for one hour. Charge

for 24 hours before conducting a long-term discharge test. Refer to OPERATION.

> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection Point.

To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency Power

Supplies Before Servicing."

INSTALLING THE EMERGENCY

BALLAST

> Disconnect AC power from the ﬁxture.

Remove the ballast channel cover and

install the emergency ballast in the ballast

channel (see Illustration 1).

> Remote mounting distance must be less

than half the maximum remote mounting

distance for the AC ballast. Consult AC

ballast manufacturer before remote

installation.

During normal operation, AC power is applied and the self-testing emergency ballast charges the battery. Connecting the

(red and white) battery connector wires enables the emergency circuit, and supplies power to the control/monitor circuit

and charging indicator light. The self-testing emergency ballast continually monitors the battery voltage, comparing it to a

preset limit. Should the unit detect an unusual voltage condition, the indicator light will flash and the internal audible alarm

will sound.

When AC power fails, the self-testing emergency ballast automatically switches to emergency mode, keeping one lamp

illuminated at a reduced lumen output for a minimum of 90 minutes. When AC power is restored, the self-testing emergency

ballast returns to charging mode and delays AC ballast operation for approximately 3 seconds to prevent false-tripping of

AC ballast (end of lamp life) shutdown circuits.

OPERATION

CHARGING INDICATOR LIGHT INSTALLATION

SELF-TESTING OPERATION

This unit contains a control/monitor circuit that automatically performs a 30-second discharge test every 30 days, and a

full 90-minute discharge test once a year. During routine testing, the self-testing emergency ballast simulates an AC power

failure causing the unit to automatically switch to emergency mode. The unit will monitor the operation of the lamps,

battery voltage, discharge current, and emergency duration. If the emergency system functions properly, then the unit will

return to normal mode. Should the unit detect any problems, the indicator light will flash continually and the audible alarm

will sound 4 times every 30 seconds until the condition has been corrected or the unit passes the next test.

To reset a failure indication, push and hold the test switch for a minimum of 15 seconds. If the condition has not been

corrected by the next scheduled test, the unit will once again detect the failure and signal the failure indicator.

To cancel a test, turn the wall switch ON (or OFF if switch is already on), wait 5 seconds, then turn it OFF (ON).

Charging

Indicator

Light

1/2" White

Bushing

Violet (+)

Brown (–)

Violet (+)

Brown (–)

1/2" White

Bushing

5/8" Black

Bushing

5/8" Black

Bushing

1/2" Punch

Fixture Fixture

Charging

Indicator

Light

NOTE: After installing the charging indicator light and test switch, mark each with the appropriate

label. If a detached charging indicator light is used, connect by matching wire colors and install as

shown above.

ILLUSTRATION 3B

STEP 2STEP 1

ILLUSTRATION 3A

MAINTENANCE

This self-testing emergency ballast automatically performs required routine testing. Results are reported to

maintenance personnel via the indicator light and audible alarm.

Note: If optional audible alarm is disabled, maintenance personnel should periodically check the indicator light. If the

indicator light is flashing, go through all steps of Troubleshooting Guide.

TROUBLESHOOTING GUIDE

STATUS INDICATORS

PROBLEM CONNECTOR

INDICATOR

LIGHT

AUDIBLE

ALARM

Light on

steady, not

ﬂashing

No beeping None Unit is Operating Correctly.

Flashing 1/2

Second

Intervals

Beeping

1/2

Second

Intervals

Line voltage;

incorrect

installation

1. Check line voltage. (Must be between 110

and 277 VAC)

2. Allow unit to charge for 24 hours. Perform manual

test. If ﬂashing/beeping continue, emergency bal-

last should be replaced.

Flashing

1/2

Second

Intervals

Beeping

4 times

every 30

seconds

Battery voltage

is outside limits. Let battery charge.

Failed scheduled

self-test

1. Check to make sure lamps are operational, speci-

ﬁed for this self-testing emergency ballast, and in

place.

2. Check that ﬁxture wiring is in accordance with

proper wiring diagram.

3. Allow unit to charge for 24 hours. Perform manual

test. If ﬂashing/beeping continue, emergency bal-

last should be replaced.

Any other erroneous status

indications

(e.g. LED indicator light off with

AC power applied)

Corrupted chip

memory

Open inverter connector (red and white

wires) and push manual test switch for 15

seconds minimum, then reconnect inverter

connector.

Failure Status will be reset when the unit passes:

• The next automatic test, or

• A manual test exceeding 15 seconds, or

• An actual power failure exceeding 15 seconds.

NOTE: It is normal for the indicator light to remain off for a few minutes

on initial start-up or after a very long power outage (discharge), as the

battery voltage rises to normal range. Refer to the Troubleshooting

Guide if this condition persists.

NOTE: The inverter connector (red and white wires) must be connected

for the AC ballast to operate normally.

FIG F THREE (3) LAMP INSTANT START BALLAST

FIG D TWO (2) LAMP INSTANT START BALLAST

FIG B ONE (1) LAMP INSTANT START BALLAST

FIG E THREE (3) LAMP RAPID START BALLAST

FIG C TWO (2) LAMP RAPID START BALLAST

FIG A ONE (1) LAMP RAPID START BALLAST

WIRING DIAGRAM for 1-LAMP emergency operation

LAMP

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

1 LAMP

RAPID

START

BALLAST

RED

BLUE

WHT

BLK

BLUE RED

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

LAMP

RED

YEL/BLK

YELLOW

BLUE

1 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE RED

BLU/WHT

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

(EMERGENCY

)

LAMP 1

RED

YEL/BLK

YELLOW

2 LAMP

RAPID

START

BALLAST

WHT

BLK

BLUE

RED

BLU/WHT LAMP 2

BLUE BLUE

RED

YELLOW

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

(EMERGENCY

)

LAMP 1

RED

YEL/BLK

YELLOW

BLUE

2 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE

RED

BLU/WHT

LAMP 2

BLUE

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

RED

()

EMERGENCY

LAMP 1

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

3 LAMP

RAPID

START

BALLAST

BLUE

WHT

BLK

YELLOW

BLUE

RED

BLU/WHT

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

()

EMERGENCY

LAMP 1

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLUE

3 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLUE

RED

BLU/WHT

BLUE

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

RAPID START AC BALLASTS INSTANT START AC BALLASTS

FIG H FOUR (4) LAMP INSTANT START BALLASTFIG G FOUR (4) LAMP RAPID START BALLAST

()

EMERGENCY

LAMP 1

LAMP 4

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

4 LAMP

RAPID

START

BALLAST

RED

WHT

BLK

YELLOW

RED

BROWN

BLUE

BLU/WHT

BROWN

BLUE

BLU/WHT

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

()

EMERGENCY

LAMP 1

LAMP 4

LAMP 2

LAMP 3

RED

YEL/BLK

YELLOW

BLUE

4 LAMP

INSTANT

START

BALLAST

WHT

BLK

BLU/WHT YELLOW

BLUEBLUE

RED

YELLOW

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

FIG J TWO (2) LAMP COMPACT INSTANT START BALLAST

FIG I ONE (1) LAMP COMPACT RAPID START BALLAST

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

INSTANT

START

BALLAST

RED

BLUE

RED

LAMP 1

LAMP 2

YELLOW

( )

EMERGENCY

WHT

BLK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

FIG K TWO (2) LAMP RAPID START BALLAST-SERIES YELLOW

()

EMERGENCY

LAMP 1

LAMP 2

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

BLUE RED

WHT

BLK

YELLOW

BLUE RED

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

FIG L TWO (2) LAMP PROGRAM RAPID START OSRAM BALLAST

()

EMERGENCY

LAMP 1

LAMP 2

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

BLUE

RED

WHT

BLK

YELLOW

BLUE

RED

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

2 LAMP

RAPID

START

BALLAST

RED

BLUE

RED

LAMP 1

LAMP 2

YELLOW

( )

EMERGENCY

WHT

BLK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

WALL SWITCH

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLACK

FIG N ONE (1) 36W-55W LAMPS WITHOUT AC BALLAST

WIRING DIAGRAMS for Emergency-Only xtures

FIG O ONE (1) 14W-55W LAMP WITHOUT AC BALLAST

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

(CAP)

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE

LAMP

(CAP)

BLACK

LAMP

RED

YEL/BLK

YELLOW

BLU/WHT

BLUE (CAP)

(CAP)

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

(CAP)

BLACK

NOTE: Installation of this self-testing ﬂuorescent emergency ballast is different

from standard models.

The emergency ballast must interrupt the switched or unswitched hot lead feeding

the AC ballast. Before beginning installation, consult these wiring diagrams.

FIG M TWO (2) LAMP RAPID START STEP DIMMING BALLAST

(EMERGENCY )

LAMP 1

RED

YEL/BLK

YELLOW

2 LAMP

RAPID

START

STEP

DIMMING

BALLAST

BLUE

RED

BLU/WHT LAMP 2

BLUE BLUE

RED

YELLOW

BLACK

WHT

BLK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

HOT

WHT/RED

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

COMMON

RED/WHT

BUZZER

SELECTOR

BLKBLK

BLK

WIRING DIAGRAM for 1-LAMP emergency operation

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

THE WHITE/BLACK LEAD MUST CONNECT TO THE WHITE

LEAD OF THE STEP-DIMMING BALLAST ASSOCIATED WITH

THE EMERGENCY BALLAST ONLY. CONNECTIONS TO OTHER

BALLASTS OR FIXTURES COULD RESULT IN ABNORMAL

OPERATION AND CAUSE PRODUCT DAMAGE.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Philips

Philips

Philips HF3670 Manual de usuario

Philips

Philips hue 17466 V7 Series Manual de usuario

Philips

Philips 56424-31-16 Manual de usuario

Philips

Philips Fluorescent Lamps Manual de usuario

Philips

Philips Ledalite Centris Wall Mount Joint 950 Manual de usuario

Philips

Philips MASTER Colour CDM-R111 Manual de usuario

Philips

Philips 56452-17-16 Manual de usuario

Philips

Philips SP160P LED40S 840 W60L60 PSU SI Guía del usuario

Philips

Philips B50ST Manual de usuario

Philips

Philips Selecon PL1 Series Manual de instrucciones

Philips

Philips Hue Runner Manual de usuario

Philips

Philips 910503700745 Manual de usuario

Philips

Philips Ecomoods 57930/**/16 Series Manual de usuario

Philips

Philips 100LT Manual de usuario

Philips

Philips ILS-CL-8RES Manual de usuario

Philips

Philips PLFRESNEL1 Manual de usuario

Philips

Philips VL440 Spot Manual de usuario

Philips

Philips Illuminate Manual de usuario

Philips

Philips Bodine B94G Type 2 Manual de usuario

Philips

Philips 30504 Manual de usuario

Philips

Philips iColor Flex LMX gen2 Manual de usuario

Philips

Philips Light System Manager Manual de usuario

Philips

Philips WHS Manual de usuario

Philips

Philips ColorBlast TRX Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario