Philips Bodine B94G Type 2 Manual de usuario
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
SAVE THESE INSTRUCTIONS
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
© Philips Emergency Lighting
A Division of Philips Electronics North America Corporation
236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine
70094021
EMERGENCY LIGHTING EQUIPMENT
Installation Instructions for TYPE 2
1. To prevent high voltage from being present on red, yellow & yellow/black output leads prior to
installation, inverter connector must be open. Do not join inverter connector until installation is
complete and AC power is supplied to the emergency ballast.
2. This product is for use with one 13 W through 42 W (4-pin) compact fluorescent lamp without integral
starter.
3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and
inverter connector of the emergency ballast before servicing.
5. This emergency ballast is for factory or field installation.
6. This product is suitable for damp locations where the ambient ballast temperature is 0°C minimum, +50°C
maximum. Product is not suitable for heated air outlets and wet or hazardous locations.
7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field
replaceable. Contact the manufacturer for information on service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualified service personnel.
B94G
03/21/11
Ni - Cd
STEP #1
WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED, YELLOW & YELLOW/
BLACK OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN.
DO NOT JOIN INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS
SUPPLIED TO THE EMERGENCY BALLAST.
NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of
power is required. The emergency ballast must be fed from the same branch circuit as
the AC ballast.
PRODUCT IDENTIFICATION AND INSTALLATION
> Compare the emergency ballast to the illustrations below and determine the Option number necessary to iden-
tify the appropriate set of wiring diagrams.
> Disconnect AC power from the fixture.
> Refer to the specific set of diagrams corresponding to the Option number determined above.
> Make electrical connections in accordance with the National Electrical Code and any local regulations. If this
product includes a test/monitor plate, it may be installed in the ceiling near the fixture or at a remote loca-
tion (up to 50 feet). The emergency ballast may be remotely installed up to half the distance the AC ballast
manufacturer recommends remoting the AC ballast from the lamp, or up to 50 feet, whichever is less. If no
AC ballast is used, the emergency ballast can be remotely mounted up to 50 feet away.
> Note: A switch box is not supplied (for use with the test/monitor plate).
> On switched fixtures, an additional unswitched hot wire (120 or 277 VAC) must be run and connected to the
emergency ballast.
STEP #2 WIRING THE EMERGENCY BALLAST
> Cut the fixture wires between the lamp holder and AC ballasts and connect the blue and blue/white emergency
ballast wires to the AC ballast and the yellow and yellow/black wires to the lamp holder.
> Connect the LED by matching violet and brown leads. For the optional tabbed LED, connect the violet lead to
positive (+) tab. For the Illuminated Test Switch (ITS) connect as shown on the wiring diagrams by matching
the violet and brown leads and by connecting the black leads to the emergency ballast.
> Follow the corresponding wiring diagram to connect the remaining leads.
> After installation is complete, supply AC power and then join the inverter connector.
STEP #3 EMERGENCY BALLAST QUICK CHECK AND LABELING
> For short-term testing of the emergency function, the battery must be charged for at least one hour. The
emergency ballast must be charged for at least 24 hours before conducting a long-term test.
> In a readily visible location, attach the label "CAUTION: This Unit Has More Than One Power Supply Connec-
tion Point. To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And
Emergency Power Supplies Before Servicing."
INSTALLATION
ITS
ITS
Option 2
ITS on
Wall Plate
Option 3
Loose ITS
Parts Kit
Option 4
Loose Test Switch
and LED Parts Kit
Option 5
Loose Test Switch
and Tabbed LED
Parts Kit
Option 1
Test Switch and
LED on Wall Plate
2
TWO (2) 4-PIN COMPACT LAMP RAPID START BALLAST
ONE (1) 4-PIN COMPACT LAMP RAPID START BALLAST
When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged. When
power fails, the emergency ballast automatically switches to emergency power, operating one lamp at reduced
illumination. When AC power is restored, the emergency ballast returns to the charging mode and delays AC ballast
operation for approximately three seconds to prevent false-tripping of AC ballast (end-of-lamp-life) shutdown circuits.
This emergency ballast will operate one 13W through 42W lamp for a minimum of 90 minutes.
Although no routine maintenance is required to keep the emergency ballast functional, it should be checked
periodically to ensure that it is working. The following schedule is recommended:
1. Visually inspect the charging indicator light monthly. It should be illuminated.
2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One lamp
should operate at reduced illumination.
3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced
illumination for at least 90 minutes.
! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !
OPERATION
MAINTENANCE
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.
WIRING DIAGRAMS FOR OPTIONS 1, 4 AND 5
3
INVERTER
CONNECTOR
RED
WHITE
CHARGING
INDICATOR
LIGHT
VIOLET
BROWN
AC
BALLAST
WALL
SWITCH
EMERGENCY
UNSWITCHED HOT
YELLOW
RED
YEL/BLK
COMMON WHITE
RED
RED
WHITE WHT/BLK
WHT/RED
BLUE
BLUE
BLU/WHT
BLUE
BLACK
TEST SWITCH
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
B
A
L
L
A
S
T
E
M
E
R
G
E
N
C
Y
INVERTER
CONNECTOR
RED
WHITE
CHARGING
INDICATOR
LIGHT
VIOLET
BROWN
AC
BALLAST
WALL
SWITCH
EMERGENCY
UNSWITCHED HOT
YELLOW
YELLOW
YELLOW
RED YEL/BLK
COMMON WHITE
RED
RED
WHITE WHT/BLK
WHT/RED
BLUE
BLUE
BLU/WHT
BLUE
BLACK
TEST SWITCH
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
B
A
L
L
A
S
T
E
M
E
R
G
E
N
C
Y
TWO (2) 4-PIN COMPACT LAMP RAPID START BALLAST
ONE (1) 4-PIN COMPACT LAMP RAPID START BALLAST
NOTE: For EMERGENCY-ONLY option, contact factory.
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.
WIRING DIAGRAMS FOR OPTIONS 2 AND 3
4
WALL
SWITCH
UNSWITCHED HOT
INVERTER
CONNECTOR
RED
WHITE
AC
BALLAST
EMERGENCY
YELLOW
RED
YEL/BLK
COMMON WHITE
RED
RED
WHITE WHT/BLK
BLUE
BLUE
BLU/WHT
BLUE
BLACK
WHT/RED
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
VIOLET
BROWN
BLACK
BLACK
VIOLET
BROWN
ITS B
A
L
L
A
S
T
E
M
E
R
G
E
N
C
Y
WALL
SWITCH
UNSWITCHED HOT
INVERTER
CONNECTOR
RED
WHITE
AC
BALLAST
EMERGENCY
YELLOW
YELLOW
YELLOW
RED YEL/BLK
COMMON WHITE
RED
RED
WHITE WHT/BLK
BLUE
BLUE
BLU/WHT
BLUE
BLACK
WHT/RED
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
VIOLET
BROWN
BLACK
BLACK
VIOLET
BROWN
ITS B
A
L
L
A
S
T
E
M
E
R
G
E
N
C
Y
Tabla de contenidos
Otros manuales de Equipo de iluminación de Philips
Philips
Philips RCH20 Manual de usuario
Philips
Philips SP160P LED40S 840 W60L60 PSU SI Guía del usuario
Philips
Philips Lightolier EG1-4 Manual de usuario
Philips
Philips 17435/**/P7 Series Manual de usuario
Philips
Philips CosmoPolis Urban Lighting Manual de usuario
Philips
Philips VL440 Spot Manual de usuario
Philips
Philips TWS101 Manual de usuario
Philips
Philips LED Luminaires Manual de usuario
Philips
Philips goLITE BLU Manual de usuario
Philips
Philips eW Flex Compact Manual de usuario
Philips
Philips TrueLine RC530B ELP3 Manual de usuario
Philips
Philips hue 17457 V7 Series Manual de usuario
Philips
Philips ColorGraze Powercore Manual de usuario
Philips
Philips 57945-17-16 Manual de usuario
Philips
Philips HF3532 Manual de usuario
Philips
Philips 56490-31-16 Manual de usuario
Philips
Philips ColorGraze IntelliHue Powercore BCS559 30x60 RGBMW... Manual de usuario
Philips
Philips 59273-17-16 Manual de usuario
Philips
Philips 57948-17-16 Manual de usuario
Philips
Philips hue 40801 Series Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
