Perlesmith PSMFK12 Manual de usuario
Model: PSMFK12
Medium Full Motion Mount Instruction Manual
V3.0
Thank you for choosing this Perlesmith product! At Perlesmith we strive
to provide you with the best quality products and services in the industry.
Please share your experience of our product with others on
www.perlesmith.com/pages/reviews if you are satisfied. Should you have
any issues, please don't hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA/DE/UK/FR/IT/ES/AU)
Web Site:
www.perlesmith.com
Please carefully read all instructions before attempting installation. If you do not under-
stand the instructions or have any concerns or questions, please contact our Technical
Support line at 1-800-556-6806 or customer service at [email protected]
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, and concrete block walls
- DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and mount
combined.
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
300 mm ≈ 11 3/4 in.
Minimum VESA pattern:
100mm/4 in.(W)x100mm/4 in.(H)
MAX:400mm/16 in.
MAX:400mm/16 in.
Check the VESA Pattern of Your TV before the Installation
IMPORTANT SAFETY INFORMATION
If your TV VESA is greater than 400x400 mm/16x16 in. or less than
VESA 100x100mm/4x4in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Verify Your Wall Construction
If you are not sure the wall
construction, please
contact our product
support line at
1-800-556-6806 or
customer service at
01
Supplied Parts and Hardware for Step 3
Supplied Parts and Hardware for Step 2（Optional）
Note: The spacer is
shown in accordance
with the actual size φ15 x φ8.2 x 10mm
x4
03 Spacers
[If necessary]
Awl
Tools Needed (Not lncluded)
Stud Finder Tape Measure Pencil Drill
5/32 in.(4mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
1/2in.(13mm )
Socket Wrench Screwdriver
Hammer Level
Supplied Parts and Hardware
Warning:This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our Product
Support line at 1-800-556-6806 or customer service at
• Please note: Not all hardware included in this package will be used.
Arm Assembly/Wall Plate x 101
Supplied Parts and Hardware for Step 1
02
Extender Bracket x 402
Bolt (X4)
M6 x 12mm
K
M6 Nuts (X4)
F
3/8 in.(10mm)
Wrench
H X1
03
Step 1 Detach Faceplate
Remove the preassembled bolts [L] using the wrench [H] or screwdriver (not included) to
separate the faceplate [01A] from the arm assembly/wall plate [01B]. Keep bolts [L] for
use in Step 5.
Lag Screws
ST7x70mm
x5
A1
Wall Anchor
φ10x70mm
x5
A2
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
Supplied Parts and Hardware for Step 4
[Only one bolt size fits your TV]
TV Bolts06
M4 x 25mm
x4
M4
Note: The bolts are shown in accordance with the actual size
M6
M6 x 25mm
x4
M8
M8 x 25mm
x4
M8 x 50mm
x4
or L
01B
01A
[S1]
[S3]
[S4] [S5]
Step 3 Secure the Faceplate [01A] or Faceplate [01A] with Extender
Brackets [02] to TV
Only one bolt size fits your TV.
M6M4 M8
for VESA hole pattern:
16 x 8 in.(400 x 200mm)
12 x 8 in.(300 x 200mm)
for VESA hole pattern:
16 x 16 in.(400 x 400mm)
12 x 12 in.(300 x 300mm)
for VESA hole pattern:
4x4 in./100x100mm
8x8 in./200x200mm
200mm
100mm
200mm
100mm
Option A
Step 2 Choose the Combination that Applies to Your VESA Hole Pattern
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Too Short Too Long Correct Correct
Select TV Bolts
04
No Need to Attach Extender
Brackets [02] to Faceplate Option B Need to Attach Extender
Brackets [02] to Faceplate
F
or
F
Note: The small bump on the
extender bracket should be
aligned with the hole on the
faceplate
Note: If necessary, the spacers can be used in multi-layer. If the installation
fails after trying various methods, please contact customer service at
Option A (For Flat Back TV)
CAUTION: Ensure the faceplate [01A] or
faceplate [01A] with extender brackets [02] is
EQUALLY CENTERED on your TV AND
securely fastened in place.
03
(If needed)
06
UP
05
Option B (For Round Back TV)
06
03
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
06
03
06
Alternate Setups
Spacer
S1 S3 S4
S1 S3
S4
S1 S3 S4 S5
S1 S3 S4 S5
Option D
06
03
For cable interference or inset holes, use
spacers [03] to create extra space between the
TV and faceplate
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the arm
assembly/wall plate [01B].
●DONOT USE ANCHOR [A2] FOR THIS STEP!
●Ensure the arm assembly/wall plate [01B] is securely fastened
to the wall before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm)
minimum 1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
Step 4A
Wood Stud Option
X
Step 4
For wood stud installation, follow STEP 4A
For concrete installation, follow STEP 4B
Attach the Arm Assembly/Wall Plate [01B] to Wall
4A-1
4A-2
Use a stud finder (not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
Awl
(Not lncluded)
Position the arm assembly/wall plate
[01B] at your desired height and line
up the holes with your stud center
line. Level the arm assembly/wall
plate [01B] and mark the holes.
06
S1 S3 S4
S5
WARNING:
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the
arm assembly/wall plate [01B].
●Ensure the arm assembly/wall plate [01B] is securely fastened to
the wall before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the arm assembly/wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Wall
Anchor
A2
Step
4B Solid Concrete or Concrete Block Option
4B-1
4A-3
4A-4
ø5/32 in.(4 mm)
2 3/4 in.(70mm)
Drill 3 pilot holes using a 5/32 in.(4 mm)
diameter drill bit. Make sure the depth is
not less than 2 3/4 in.(70mm).
3/8in.(10mm)
Socket Wrench
(Not lncluded)
Install the arm arm assembly/wall
plate [01B] using lag screws [A1].
Tighten the lag screws [A1] only until
they are pulled firmly against the wall
plate.
HEAVY! You may need
assistance with this step.
A1
Position arm assembly/wall
plate [01B] at your desired
height, level the arm
assembly/wall plate and
mark the pilot hole locations.
07
4B-2
ø3/8 in.(10mm)
3 in.(75mm)
Drill 5 pilot holes using a
3/8 in.(10mm) diameter drill bit. Make sure
the depth is not less than 3 in.(75mm). Never
drill into the mortar between blocks.
4B-3
A2
Use the hammer to knock anchors [A2]
into the wall. Be sure the anchors [A2]
are seated flush with the concrete
surface.
4B-4
Install the arm assembly/wall plate [01B] using lag screws [A1] and anchors [A2].
Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.
DO NOT over-tighten the lag screws [A1].
3/8in.(10mm)
Socket Wrench
(Not lncluded)
08
A1
Adjustments
1. Loosen both tilt bolts [S] a little.
2. Adjust TV to your desired tilt angle.
3. Retighten both tilt bolts [S] to fix
the tilt angle.
Loosen
Tighten
09
Secure TV to Arm Assembly/Wall Plate [01B]
Step 5
Step 6
Attach the TV with faceplate to the arm assembly/wall plate,
then tighten bolts [L] using wrench [H] or screwdriver(not
included) to secure the TV to the arm assembly/wall plate
Screwdriver
(Not included)
or
L
You may need
assistance with
this step.
1. Loosen the two level bolts [L] a little on the rear
of the arm assembly/wall plate.
2. Level your TV.
3. Retighten two level bolts [L] to hold TV in place.
or
L
Loosen
Tighten
Loosen
Tighten
S
Level Adjustment
6-1
Tilt Adjustment
6-2
Tabla de contenidos
Otros manuales de Rack y soporte de Perlesmith
Perlesmith
Perlesmith PSTVS01 Manual de usuario
Perlesmith
Perlesmith PSTVMC01 Manual de usuario
Perlesmith
Perlesmith PSTVMC01 Manual de usuario
Perlesmith
Perlesmith PSLT3 Manual de usuario
Perlesmith
Perlesmith PSTVS16 Manual de usuario
Perlesmith
Perlesmith PSMFK9 Manual de usuario
Perlesmith
Perlesmith PSTVS09 Manual de usuario
Perlesmith
Perlesmith PSTVS01 Manual de usuario
Perlesmith
Perlesmith PSTVS06 Manual de usuario
Perlesmith
Perlesmith PSSS1 Manual de usuario
Perlesmith
Perlesmith PSSS1 Manual de usuario
Perlesmith
Perlesmith PSTVS01 Manual de usuario
Perlesmith
Perlesmith PSLF2 Manual de usuario
Perlesmith
Perlesmith PSDSK1 Manual de usuario
Perlesmith
Perlesmith MD2296 Manual de programación
Perlesmith
Perlesmith PSFS03 Manual de usuario
Perlesmith
Perlesmith PSSS2 Manual de usuario
Perlesmith
Perlesmith PSFS04 Manual de usuario
Perlesmith
Perlesmith PSTVS15 Manual de usuario
Perlesmith
Perlesmith PSSS3 Manual de usuario
