Perle SR-100 Series Manual de usuario

P/N 5500443-10 (Rev F)

Perle Fast Ethernet

Media Converters

Installation Guide

SR-100-XXXXXX- (XT)

SR-100-SFP- (XT)

Perle SR-100 Fast Ethernet Media Converter Installation Guide 2

Preface

Audience

This guide is for the network or computer technician responsible

for installing the Perle SR-100 Gigabit Media Converter. Familiarity

with the concepts and terminology of Ethernet and local area

networks is required.

Purpose

This document describes the hardware and physical

characteristics of the Perle SR-100 Media Converter. It covers

hardware features as well as installation and operation of the

SR-100.

Package Contents

•SR-100 Media Converter with attached DIN Rail mounting

bracket

•Installation Guide (this guide)

Document Conventions

Note: Means reader take note: notes contain helpful suggestions.

Caution: Means reader be careful. In this situation, you might

perform an action that could result in equipment damage or loss of

data.

Warning: IMPORTANT SAFETY INSTRUCTIONS

Means danger. You are in a situation that could cause bodily

injury. Before you work on any equipment, be aware of the

hazards involved with electrical circuitry and be familiar with

standard practices for preventing accidents. Only qualified

personnel should connect power to this unit.

Cautions and Warnings

Warning: Power sources must be off prior to beginning the power

connection steps. Read the installation instructions before you

connect the unit to its power source.

Warning: These devices are open-type devices that are to be

installed in an enclosure with a tool removable cover or door,

suitable for the environment.

Perle SR-100 Fast Ethernet Media Converter Installation Guide 3

Warning: Power supply of the equipment must be rated

appropriately (See the Technical Specification section for

specification with limited power). Limited power means complying

with one of the following:

•Class 2 circuit according to Canadian Electrical Code, Part 1,

C22.1

•Class 2 circuit according to National Electrical Code, NFPA-70

•Limited Power Supply (LPS) according to EN/IEC 60950-1.

•Limited-energy circuit according to EN/IEC 61010-1

Warning: If this equipment is used in a manner not specified by

the manufacturer, the protection provided by the equipment may

be impaired.

Warning: In case of malfunction or damage, no attempts at repair

should be made by the user. All repairs need to be made by a

qualified Perle representative. Do not dismantle this product.

Warning: Transient protection shall be provided that is set at a

level not exceeding 140% of the peak rated voltage value at the

supply terminals to the equipment.

Perle SR-100 Fast Ethernet Media Converter Installation Guide 4

Overview

This document contains instructions necessary for the installation

and operation of the Perle Industrial Fast Ethernet Media

Converters (SR-100). These products convert a 100Base-TX

cable connection (copper) to a 100Base-X connection (fiber).

The fiber connection can be either single mode (SM) or multimode

(MM) and can operate over different wavelengths and distances,

depending on the model selected (see table below). Perle Media

Converters (SR-100) are also available in Extended Temperature

models.

Model Connector Mode - Distance Wavelength

SR-100-SC2 (XT) SC MM – 2 km/1.25 mi.

1310 nm

SR-100-ST2-(XT) ST MM – 2 km/1.25 mi. 1310 nm

SR-100-SC2U SC MM – 2 km/1.25 mi.

1310/1550 nm

SR-100-SC2D SC MM – 2 km/1.25 mi. 1550/1310 nm

SR-100-ST2U SC MM – 2 km/1.25 mi.

1310/1550 nm

SR-100-ST2D SC MM – 2 km/1.25 mi. 1550/1310 nm

SR-100-SC20 (XT) SC SM – 20 km/12.4 mi. 1310 nm

SR-100-ST20 (XT) ST SM – 20 km/12.4 mi. 1310 nm

SR-100-SC20U (XT) SC SM – 20 km/12.4 mi. 1310/1550 nm

SR-100-SC20D (XT) SC SM – 20 km/12.4 mi. 1550/1310 nm

SR-100-SC40 (XT) SC SM – 40 km/25 mi. 1310 nm

SR-100-ST40 (XT) ST SM – 40 km/25 mi. 1310 nm

SR-100-SC40U SC SM – 40 km/25 mi. 1310/1490 nm

SR-100-SC40D ST SM – 40 km/25 mi. 1490/1310 nm

Perle SR-100 Fast Ethernet Media Converter Installation Guide 5

SR-100-SC80 SC SM – 80 km/50 mi. 1550/1590 nm

SR-100-ST80 ST SM – 80 km/50 mi. 1590/1550 nm

SR-100-SC120 SC SM – 120 km/74.6 mi. 1550 nm

SR-100-ST120 ST SM – 120 km/74.6 mi. 1550 nm

SR-100-SFP-(XT) SFP Note 1

Note 1: Fiber characteristics will depend on the SFP fiber module

selected

Note: Please visit Perle’s web site for the most up to date

Installation guides, models and specifications:

http://www.perle.com/

Perle SR-100 Fast Ethernet Media Converter Installation Guide 6

Installation

These are the steps required to configure the SR-100 Fast

Ethernet media converter:

1. Insert SFP Module (SFP Model only).

2. Set the DIP switch settings. (optional)

3. Install and connect the fiber cable.

4. Install and connect the copper cable.

5. Power up the media converter.

Accessing the DIP Switches

To access the DIP switches:

1. Disconnect the power source.

2. Release both tabs as located in the diagram (Step 1).

3. Gently side the case open 1/3 of the way to expose the DIP

switches (Step 2). You will hear an audible click. Do not force

the case completely open.

Perle SR-100 Fast Ethernet Media Converter Installation Guide

DIP Switches

Set the DIP Switches accordingly, and then slide the case

together until you hear an audible click.

1 Reserved

2 Auto Negotiation

3 Smart Link Pass-Through

4 Far End Fault

5 Reserved

6 Pause

7 Loopback

8 Reserved

Perle SR-100 Fast Ethernet Media Converter Installation Guide 8

DIP Switch Settings

Reserved (Switch 1)

Auto Negotiation (Switch 2)

Switch Position Mode

Up (default) On

Down Off

Auto: In this mode of operation the media converter will negotiate

Ethernet parameters on the copper connection. This will ensure

the most optimal connection parameters will be in effect. If the

copper link partner does not support Auto negotiation, the SR-100

will default to 100 Mbps and Half Duplex mode.

Off: Auto Negotiation should only be turned off, if the copper link

partner does not support Auto Negotiation.

When the Auto Negotiation switch is set to the Off position, the

media converter will operate at 100 Mbps and Full Duplex mode.

Smart Link Pass-Through (Switch 3)

Switch Position Mode

Up (default) Enable

Down Disable

Enable: In this mode, the link state on one connection is directly

reflected through the media converter to the other connection. If

link is lost on one of the connections, then the other link will be

brought down by the media converter.

If the installation has a media converter on both ends of the fiber

link and both are setup for Link Pass-Through, then a loss of

copper link on the far end device will propagate through both

media converters and will result in a loss of copper link at the near

end device. This would, therefore, resemble a direct copper

connection.

Disable: In this mode, the links on the fiber and copper sides can

be brought up and down independently of each other. A loss of

link on either the fiber ports or copper ports can take place without

affecting the other connection.

Perle SR-100 Fast Ethernet Media Converter Installation Guide 9

Far End Fault (Switch 4)

Switch Position Mode

Up (default) Enabled

Down Disabled

Enabled: If the media converter detects a loss of fiber signal on

the fiber receiver, it will immediately send a FEF on the fiber link.

This, in effect, notifies the fiber link partner that an error condition

exists on the fiber connection.

If the remote media converter is set up for Far End Fault (FEF)

and the local media converter is set up with Link Pass-Through, a

loss of fiber link on either the transmit or receive line will be

passed through to the local copper connection thus notifying the

connected device.

If the media converter has been set to Link Pass-Through mode,

the effect will be the same as FEF, since the link loss on the fiber

receiver will bring down the copper link, which will in turn cause

the transmit fiber link to be brought down.

NOTE: This switch needs to be set to either generate or detect

the FEF signal.

Disabled: The media converter will not monitor for or generate Far

End Fault.

The following diagram is an illustration of the operation of this

feature.

(A) – Remote Media Converter setup for Far End Fault

Enabled, Auto Negotiation – OFF and Link Mode – Standard.

(B) – Local Media Converter setup for Link Pass-Through and

Auto Negotiation - OFF

(A) loses fiber connection on its receiver

(A) sends an FEF

(B) detects loss of link in its fiber receiver

(B) drops link on copper connection through Link Pass-Through

(A) Link on copper connection is not affected.

Perle SR-100 Fast Ethernet Media Converter Installation Guide 10

Reserved (Switch 5)

Pause (Switch 6)

Switch Position Mode

Up (default) Auto

Down Half

Auto: When Auto Negotiation has been set to Auto (SW 2), the

media converter will use this setting for its Ethernet parameter

negotiation on the copper connection.

Half: The media converter will not negotiate support for the Pause

feature.

NOTE: The media converter will not act on, or generate any

Ethernet Pause messages, but will pass them through to the end

device. This switch setting is provided so that the attached device

(near end) can negotiate its Ethernet parameters as if it was

negotiating directly with the far end device. The Pause switch

setting on the media converter should match the capabilities of the

far end device.

Loopback (Switch 7)

Switch Position Mode

Up (default) Disabled

Down Enabled

Disabled: The loopback feature is disabled. This is the normal

position for regular operation. The switch must be set to this

position for data to pass through the media converter.

Enabled: This is a test mode. All data received on the receive

(RX) fiber connection is looped back to the transmit (TX) fiber

connection. The state of the copper is not relevant and no data or

link status is passed through to the copper side.

Reserved (Switch 8)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Perle

Perle

Perle S-4GPT-DSFP Manual de usuario

Perle

Perle C-1110-M2SC05 Manual de usuario

Perle

Perle S-10GT-SFP Manual de usuario

Perle

Perle SMI-10GT Manual de usuario

Perle

Perle C-10G-STS Manual de usuario

Perle

Perle S-10GRT-SFP Manual de usuario

Perle

Perle S-10G-XTXH Manual de usuario

Perle

Perle S-1000-SFP Manual de usuario

Perle

Perle S-110 series Manual de usuario

Perle

Perle S-1110HP Manual de usuario

Perle

Perle S-1110-XT Manual de usuario

Perle

Perle C-1110-XXXXX Manual de usuario

Perle

Perle C-100-XXXXX Manual de usuario

Perle

Perle S-1110HP-XT Manual de usuario

Perle

Perle S-1110-M2xx05 Manual de usuario

Perle

Perle S-110-P Manual de usuario

Perle

Perle SMI Media Converter Manual de usuario

Perle

Perle MCR1900 Manual de usuario

Perle

Perle SMI Media Converter Manual de usuario

Perle

Perle MCR200 Manual de usuario

Perle

Perle S-1000MM-XXXXXX Manual de usuario

Perle

Perle S-110-P Manual de usuario

Perle

Perle S-1110-XT 10 Manual de usuario

Perle

Perle MCR1900 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario