Perle S-10GRT-SFP Manual de usuario
P/N 5500432-10 (Rev-E)
Perle S-10GRT-SFP
Media Converter
Installation Guide
Perle S 10GRT-SFP Media Converter Installation Guide 2
Overview
This document contains instructions necessary for
the installation and operation of the Perle
S-10GRT-SFP Standalone Media Converter. This
media converter contains one pluggable
transceiver port that permits insertion of a
SFP/SFP+ and one integrated rate converting
(10/100/1G/2.5G/10G RJ45 copper port. This
media converter can use either Perle Systems or
third party MSA compatible 1G/10G SFP+ modules.
See the Technical Specifications section in this
guide for supported models.
Visit Perle’s web site for the most up to date
Installation guides, models and specifications.
http://www.perle.com/
Getting to know your S-10GRT-
SFP Media Converter
Your Perle 10-GRT-SFP Standalone Media
Converter package consists of the following items:
•S-10GRT-SFP with one RJ45 copper port and
one SFP/SFP+ transceiver port.
•Grounding screws
•Country specific power adapter
•Power cord strain relief clip
•Four rubber feet
•This guide
Perle S 10GRT-SFP Media Converter Installation Guide 3
Front View
Perle S 10GRT-SFP Media Converter Installation Guide 4
Installation
The default switch setting (all switches in the UP
position) will work for most installations.
These are the steps required to configure the
media converter.
1. Set the DIP switch settings. (optional)
2. Insert the appropriate SFP/SFP+ into the
transceiver port.
3. Connect the fiber cable.
4. Connect the RJ45 (copper cable).
DIP Switches
Perle S 10GRT-SFP Media Converter Installation Guide 5
DIP Switch Settings
The DIP switches are located on the side of the
unit.
Note: Switch changes made when the unit is
powered up take effect immediately and will result
in a link reset on both ports.
Link Mode (Switch 1)
Switch Position
Mode
Up (default)
Smart Link Pass-through
Down
Standard
Smart Link Pass-through: In this mode, the link
state on one port connection is directly reflected
through the media converter to the other port
connection. If link is lost on one of the connections,
then the other link will be brought down by the
media converter.
Standard: In this mode, the links can be brought up
and down independently of each other. A loss of
link on either connection can occur without
affecting the other connection.
Fiber Fault Alert (Switch 2)
Switch Position
Mode
Up (default)
Enabled
Down
Disabled
Enabled: If the media converter detects a loss of
signal on the fiber port, the media converter
notifies the link partner on that same port that an
error condition exists by bringing down the link.
Perle S 10GRT-SFP Media Converter Installation Guide 6
Disabled: The media converter will not monitor for
fiber fault.
Fiber Fault Alert Sample
Config
Media Converter A Configuration
•Link Mode –Standard Mode
•Fiber Fault Alert
Media Converter B Configuration
•Link Mode–Smart Link Pass through Mode
•Fiber Fault Alert
Perle S 10GRT-SFP Media Converter Installation Guide 7
Sequence of Events
1. Media Converter Aloses fiber connection (RX).
2. Media Converter Anotifies the remote Media
Converter that there is a fault on the Link.
3. Media Converter Bdetects loss of fiber link on
receiver (RX).
4. Media Converter Bturns off transmitter (TX).
Cut-through / Rate converting (Switch 3)
Switch Position
Type
Up (default)
Rate converting
Down
Cut-through
Rate converting: Both ports can operate at the
same or different speeds.
Cut-through: Both ports need to be the same
speed and set to full duplex mode.
Fiber Interface Loopback (Switch 4)
Switch Position
Mode
Up (default)
Disabled
Down
Enabled
Disabled: When disabled, the media converter will
not be in Fiber loopback mode.
Enabled: When enabled, the media converter will
be in Fiber loopback mode.
Perle S 10GRT-SFP Media Converter Installation Guide 8
Copper Negotiation (Switch 5)
Switch Position
Mode
Up (default)
Auto
Down
Manual
Auto: The media converter will auto negotiate
copper link parameters.
Manual: The media converter will use the
parameters as defined by Switch 6 and 7.
Copper Duplex (Switch 6)
Switch Position
Mode
Up (default)
Full Duplex
Down
Half Duplex
Note Switch 5 must be set to manual for this
setting to take affect.
UP: The copper port will be set to Full Duplex
mode.
Down: The copper port will be set to Half Duplex
mode.
Perle S 10GRT-SFP Media Converter Installation Guide 9
Copper Speed (Switch 7)
Switch Position
Mode
Up (default)
100Mbps
Down
10Mbps
Note Switch 5 must be set to manual for this
setting to take affect.
UP:The copper port will be fixed at 100 Mbps.
Down: The copper port will be fixed at 10 Mbps.
Perle S 10GRT-SFP Media Converter Installation Guide 10
SGMII Interface Support
The Perle Standalone Media Converter supports
SGMII on the SFP interface for the SFPs that require
1000 Mbps SGMII.
1. Remove the top of the unit to access the
internal jumpers.
2. The SGMII jumper is located on the outer edge,
at the midpoint of the card (P3). Jumper Pin 1
and Pin 2.
Tabla de contenidos
Otros manuales de Convertidor de medios de Perle
Perle
Perle S-1110-M2xx05 Manual de usuario
Perle
Perle S-1110HP Manual de usuario
Perle
Perle S-110-P Manual de usuario
Perle
Perle S-100-XXXXX Manual de usuario
Perle
Perle C-10G-STS Manual de usuario
Perle
Perle SMI Media Converter Manual de usuario
Perle
Perle C-10GRT-SFP Manual de usuario
Perle
Perle MCR1900 Manual de usuario
Perle
Perle S-10GT-SFP Manual de usuario
Perle
Perle C-1000-XXXXX Manual de usuario
Perle
Perle S-1110P Manual de usuario
Perle
Perle C-1000MM-XXXXXX Manual de usuario
Perle
Perle SMI Media Converter Manual de usuario
Perle
Perle S-1000MM-XXXXXX Manual de usuario
Perle
Perle S-1110-XT 10 Manual de usuario
Perle
Perle S-10GR-STS Manual de usuario
Perle
Perle S-4GPT-DSFP Manual de usuario
Perle
Perle SMI Media Converter Manual de usuario
Perle
Perle C-1110-M2SC05 Manual de usuario
Perle
Perle S-1000-SFP Manual de usuario
