Perle C-100-XXXXX Manual de usuario

Este manual sirve para los siguientes modelos

39

Tabla de contenidos

Otros manuales de Convertidor de medios de Perle

Perle

Perle S-1110HP Manual de usuario

Perle

Perle S-110-P Manual de usuario

Perle

Perle SR-100 Series Manual de usuario

Perle

Perle SMI Media Converter Manual de usuario

Perle

Perle MCR1900 Manual de usuario

Perle

Perle C-10GT-SFP Manual de usuario

Perle

Perle S-10GT-SFP Manual de usuario

Perle

Perle C-1110 Series Manual de usuario

Perle

Perle S-1000MM-XXXXXX Manual de usuario

Perle

Perle S-110-P Manual de usuario

Perle

Perle S-1110P Manual de usuario

Perle

Perle S-10G-XTXH Manual de usuario

Perle

Perle C-10GRT-SFP Manual de usuario

Perle

Perle S-100-XXXXX Manual de usuario

Perle

Perle C-1000MM-XXXXXX Manual de usuario

Perle

Perle C-10G-STS Manual de usuario

Perle

Perle C-1110-XXXXX Manual de usuario

Perle

Perle S-100MM-XXXXX Manual de usuario

Perle

Perle S-10GR-STS Manual de usuario

Perle

Perle SMI Media Converter Manual de usuario

Perle

Perle MCR200 Manual de usuario

Perle

Perle C-110-M2ST2 Manual de usuario

Perle

Perle S-1110P Manual de usuario

Perle

Perle S-1110-M2 05 Series Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario

P/N 5500306-15

Perle Fast Ethernet

Media Converter

Module

Installation Guide

C-100-XXXXX Unmanaged Module

CM-100-XXXXX Managed Module

Fast Ethernet Media Converter – Installation Guide

2

Overview

This document contains instructions necessary for the installation and

operation of the Perle Fast Ethernet Media Converter Module(s) (C-100

and CM-100) that are used in conjunction with a Perle MCR Chassis.

The C-100 are unmanaged media converter modules, and the CM-100

are the managed versions. These products convert a 100Base-T cable

connection (copper) to a 100Base-X connection (fiber). The fiber

connection can be either single mode (SM) or multimode (MM) and can

operate over different wavelengths and distances, depending on the

model selected (see table below). For information on the management

options of the CM-100 module, refer to the MCR-MGT Module User’s

Guide.

Model Connector Mode - Distance Wavelength

C-100-M2xx2

CM-100-M2xx2

SC/ST/LC MM - 2 km/1.2 mi. 1310 nm

C-100-S2xx20

CM-100-S2xx20 SC/ST/LC SM - 20 km/12.4 mi. 1310 nm

C-100-S2xx40

CM-100-S2xx40

SC/ST/LC SM - 40 km/24.9 mi. 1310 nm

C-100-S2xx80

CM-100-S2xx80 SC/ST/LC SM - 80 km/49.7 mi. 1550 nm

C-100-S2xx120

CM-100-S2xx120

SC/ST/LC SM - 120 km/74.6 mi 1550 nm

C-100-S1SC20U

CM-100-S1SC20U

SC SM - 20 km/12.4 mi. 1310/1550 nm

C-100-S1SC20D

CM-100-S1SC20D

SC SM - 20 km/12.4 mi. 1550/1310 nm

C-100-S1SC40U

CM-100-S1SC40U

SC SM - 40 km/24.9 mi. 1310/1550 nm

C-100-S1SC40D

CM-100-S1SC40D SC SM - 40 km/24.9 mi. 1550/1310 nm

Note: Please refer to Perle’s web site for the most up to date

Installation guides, models and specifications:

http://www.perle.com/

Fast Ethernet Media Converter – Installation Guide

3

Installation

The module comes equipped with a bank of DIP switches and

jumpers for setting configuration.

The default DIP switch settings (all switches in the UP position)

and jumper settings will work for most installations..

The following steps are used to configure the Perle Fast

Ethernet Media Converter Module:

1. Set the Auto-MDIX jumper (optional).

2. Set the Auto-Config jumper (CM-100 only) (optional)

3. Set the DIP switch settings (optional).

4. Insert the Media Converter Module into the chassis.

5. Connect the fiber cable.

6. Connect the copper cable.

Auto-MDIX Jumper

Note: The factory settings for Auto-MDIX will work for most

installations, but if there is a need to modify the settings, follow

the procedure below.

The AUTO-MDIX jumper (J5) is located on the upper edge, at

the midpoint of the module (see diagram below for labelling). By

covering or strapping pins 1 and 2, the C-100 and CM-100 will

operate as an MDI device. By covering or strapping pins 2 and 3,

the C-100 and CM-100 will automatically detect the Ethernet

cable’s polarity and configure itself as either an MDI or an MDIX

device. Removing the strapping is the same as AUTO.

NOTE: The default jumper setting is Auto

Fast Ethernet Media Converter – Installation Guide

Auto-Config Jumper (CM-100 only)

The Auto-Config jumper (J6) is located just below the Auto-MDIX

jumper (see above). Refer to the diagram below for labelling.

This jumper only applies to CM-100 modules.

Strapping pins 1 and 2 of the jumper will set the module in SW

mode and strapping pins 2 and 3 will set it in Auto Config mode.

Auto: When set to Auto the module will, at power-up, check its

internal flash memory to see if configuration information has

been downloaded to it from a management module. If so it will

use this as its running configuration. If there is no configuration

in flash it will read the settings of the DIP switches and use those

as its running configuration.

SW: When set to SW (Switch), the module will, at power-up,

read the settings of the DIP Switches and use those as it running

configuration. It will ignore any configuration information in its

flash memory.

NOTE: The default jumper setting is Auto

Fast Ethernet Media Converter – Installation Guide

5

DIP Switches

DIP Switch Settings

Auto Negotiation (Switch 1)

Switc

h

Position Mode

Up (default) Auto

Down Off

Auto: In this mode of operation the Media Converter Module will

negotiate Ethernet parameters on the copper connection. This will

ensure the most optimal connection parameters will be in effect. If the

copper link partner does not support Auto negotiation, the C-100 and

CM-100 will default to 100 Mbps and Half Duplex mode.

Off: Auto Negotiation should only be turned off, if the copper link

partner does not support Auto Negotiation.

When the Auto Negotiation switch is set to the OFF position, the

Media Converter Module will operate at 100 Mbps and Full Duplex

mode.

Fast Ethernet Media Converter – Installation Guide

6

Link Mode (Switch 2)

Switch

Position Mode

Up (default) Link Pass-Through Mode

Down Standard Mode

Link Pass-Through: In this mode, the link state on one connection is

directly reflected through the Media Converter Module to the other

connection. If link is lost on one of the connections, then the other link

will be brought down.

With Media Converters on both ends of the fiber link and both setup

for Link Pass-Through, then a loss of copper link on the far end

device will propagate through both Converters and will result in a loss

of copper link at the near end device. This would, in effect, resemble

a direct copper connection.

Standard Mode: In this mode, the links on the fiber and copper sides

can be brought up and down independently of each other. A loss of

link on either the fiber or copper port can occur without affecting the

other connection.

Far End Fault (Switch 3)

Switch

Position Mode

Up (default) Enabled

Down Disabled

Enabled: If the Media Converter Module detects a loss of fiber signal

on the fiber receiver, it will immediately send a FEF on the fiber link.

This, in effect, notifies the fiber link partner that an error condition

exists on the fiber connection.

If the remote Media Converter is set up for Far End Fault (FEF) and

the local Media Converter is set up with Link Pass-Through, a loss of

fiber link on either the transmit or receive line will be passed through

to the local copper connection thus notifying the connected device.

Fast Ethernet Media Converter – Installation Guide

7

If the Media Converter has been set to Link Pass-Through mode, the

effect will be the same as FEF, since the link loss on the fiber receiver

will bring down the copper link, which will in turn cause the transmit

fiber link to be brought down.

Note: If it is required to either generate or detect the FEF signal, then

the FEF switch needs to be set.

Disabled: The Media Converter Module will not monitor for, or

generate Far End Fault.

The following diagram is an illustration of the operation of this feature.

(A) – Remote Media Converter setup for Far End Fault Enabled, Auto

Negotiation – OFF and Link Mode – Standard.

(B) – Local Media Converter setup for Link Pass-Through - Enabled

and Auto Negotiation - OFF

1 – (A) loses fiber connection on its receiver

2 – (A) sends an FEF

3 – (B) detects loss of link in its fiber receiver

4 – (B) drops link on copper connection through Link Pass-Through

5 – (A) Link on copper connection is not affected.

Fast Ethernet Media Converter – Installation Guide

8

Unused (Switch 4)

Pause (Switch 5)

Switch

Position Mode

Up (default) Enabled

Down Disabled

Enabled: When Auto Negotiation has been set to Auto (SW 1), the

Media Converter Module will use this setting for its Ethernet

parameter negotiation on the copper connection.

Disable: The Media Converter Module will not negotiate support for

the Pause feature.

Note: The Media Converter Module will not act on, or generate any

Ethernet Pause messages, but will pass them through to the end

device. This switch setting is provided so that the attached device

(near end) can negotiate its Ethernet parameters as if it was

negotiating directly with the far end device. The Pause switch setting

on the Media Converter Module should match the capabilities of the

far end device.

Loopback (Switch 6)

Switch

Position Mode

Up (default) Disabled

Down Enabled

Disabled: This is the normal position for regular operation. The switch

must be set to this position in order for data to pass through the

Media Converter Module.

Enabled: This is a test mode. All data received on the receive (RX)

fiber connection is looped back to the transmit (TX) fiber connection.

The state of the copper is not relevant and no data or link status is

passed through to the copper side.

Fast Ethernet Media Converter – Installation Guide

9

Installing or Replacing Media Converter

Modules

Caution: Observe electrostatic discharge precautions when

installing the Media Converter Module(s) into the Chassis.

Failure to observe this caution could result in damage to the

Module(s) and/or chassis.

The Perle Media Converter Modules can be installed in any available

slot and in any order within the MCR Chassis.

Installing or Replacing a Media Converter Module

1. Remove the Media Converter Module from its packaging.

2. Using a cross-head screwdriver, remove the screw holding

the face plate to the Chassis to reveal the slot opening.

3. Set the jumpers and DIP switches on the Media Converter

Module to the desired operating mode.

4. Locate the top and bottom alignment guides inside the

MCR Chassis.

5. Using the module alignment guides gently slide the module

into the slot until it becomes flush with the front of the

Chassis. Light pressure may be needed to seat the module.

Do not force the module as you might cause damage. If

there is resistance, remove the module and check the

module connector for damaged or incorrectly aligned pins.

If these are not damaged, retry module insertion.

6. Tighten the captive retainer screw to ensure the Media

Converter Module is locked in place.

Fast Ethernet Media Converter – Installation Guide

10

7. Remove the dust cap from the fiber connector and connect

the fiber and copper cables.

Removing Media Convert Modules

1. Loosen the captive retainer screw on the front of the Media

Converter Module and gently pull the module out.

2. If not inserting a replacement Media Converter Module,

cover the opened slot with a face plate and secure the

screw.

Installing the Duplex Fiber Cable

Locate a 100Base-X compliant duplex (2 strands) fiber cable

with the appropriate connectors.

Connect the fiber cables from the Media Converter Module to the

other Media Converter/switch/fiber device ensuring that the RX

and TX are reversed at the opposite end.