Perle C-1000MM Series Manual de usuario
P/N 5500315-11 (Rev A)
Perle Gigabit
Fiber to Fiber
Media Converter
Module
Installation Guide
C-1000MM-XXXXXX Unmanaged Module
CM-1000MM-XXXXXX Managed Module
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
2
Overview
This document contains instructions necessary for the installation
and operation of the Perle Gigabit Fiber to Fiber Media Converter
Module(s) that are used in conjunction with a Perle MCR chassis.
The C-1000MM media converters are unmanaged modules, and
the CM-1000MM are the managed converter modules. These
products allow dissimilar 1000Base-X fiber interfaces to connect to
one another. For information on the management options of the
CM-1000MM module, refer to the MCR-MGT Module User’s
Guide.
These are the fiber to fiber conversion models:
•Multimode to Multimode (MM)
•Multimode to Single Mode (SM)
•Multimode to Single Mode Single Strand (MM)
The first fiber port will be multimode (MM) and the second fiber
port can be either single mode (SM) or multimode (MM) depending
on the model selected. They can operate over different
wavelengths and distances. (See tables below).
These products allow dissimilar to connect to one another. For
information on the management options of the CM-1000MM
module, refer to the MCR-MGT Module User’s Guide.
Fiber port 1 – MM1
Model Connector Mode Distance Wavelength
(TX/RX)
All models SC/ST/LC MM. 550 m/1804 ft. 850 nm
Fiber port 2 – MM2/SM2
Model Connector Mode Distance Wavelength
(TX/RX)
C-1000MM-M2xx05
CM-1000MM-M2xx05 SC/ST/LC MM 550 m/1804 ft. 850 nm
C-1000MM-M2xx2
CM-1000MM-M2xx2 SC/ST/LC MM 2 km/1.2 mi. 1310 nm
C-1000MM-S2xx10
CM-1000MM-S2xx10 SC/ST/LC SM 10 km/6.2 mi. 1310 nm
C-1000MM-S2xx40
CM-1000MM-S2xx40 SC/ST/LC SM 40 km/24.9 mi. 1310 nm
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
3
Model Connector Mode Distance Wavelength
(TX/RX)
C-1000MM-S2xx70
CM-1000MM-S2xx70 SC/ST/LC SM 70 km/43.5 mi. 1550 nm
C-1000MM-S2xx120
CM-1000MM-S2xx120 SC/ST/LC SM 120 km/74.6 mi. 1550 nm
C-1000MM-S1SC10U
CM-1000MM-S1SC10U SC SM 10 km/6.2 mi. 1310/1490 nm
C-1000MM-S1SC10D
CM-1000MM-S1SC10D SC SM 10 km/6.2 mi. 1490/1310 nm
C-1000MM-S1SC20U
CM-1000MM-S1SC20U SC SM 20 km/12.4 mi. 1310/1490 nm
C-1000MM-S1SC20D
CM-1000MM-S1SC20D SC SM 20 km/12.4 mi. 1490/1310 nm
C-1000MM-S1SC40U
CM-1000MM-S1SC40U SC SM 40 km/25 mi. 1310/1490 nm
C-1000MM-S1SC40D
CM-1000MM-S1SC40D SC SM 40 km/25 mi. 1490/1310 nm
C-1000MM-S1SC80U
CM-1000MM-S1SC80U SC SM 80 km/50 mi. 1510/1590 nm
C-1000MM-S1SC80D
CM-1000MM-S1SC80D SC SM 80 km/50 mi. 1590/1510 nm
C-1000MM-S1SC120U
CM-1000MM-S1SC120U SC SM 120 km/74.6 mi. 1510/1590 nm
C-1000MM-S1SC120D
CM-1000MM-S1SC120D SC SM 120 km/74.6 mi. 1590/1510 nm
Note 2: Please refer the Perle web site for the most up to date
Installation guides, models and specifications.
http://www.perle.com/
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
4
Installation
The default switch settings (all switches in the UP position) will
work for most installations. See the Operation section of this guide
for more details.
The module comes equipped with a bank of DIP switches and
jumpers for setting configuration
The default DIP switch settings (all switches in the UP position)
and jumper setting will work for most installations.
The following steps are used to configure the Perle Gigabit Fiber
to Fiber Media Converter Module:
1. Set the Auto-Config jumper. (CM-1000MM only) (optional)
2. Set the DIP switch settings (optional).
3. Insert the Media Converter Module into the chassis.
4. Connect the fiber cables.
Auto-Config Jumper (CM-1000MM only)
The Auto-Config jumper is J5.
Refer to the diagram below for labelling.
Auto (Pin 2 and Pin 3 are strapped): When set to Auto the
module will, at power-up, check its internal flash memory to see if
configuration information has been downloaded to it from a
management module. If so, it will use this as its running
configuration. If there is no configuration in flash it will read the
settings of the DIP switches and use those as its running
configuration.
SW: (Pin 1 and Pin 2 are strapped): When set to SW (Switch),
the module will, at power-up, read the settings of the DIP Switches
and use those as it running configuration. It will ignore any
configuration information in its flash memory.
NOTE: The default jumper setting is Auto
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
5
D P Switch Settings
Fiber Negotiation (Switch 1)
Switch Position
Mode
Up (default) Auto
Down Off
Auto: In this mode of operation the Media Converter will negotiate
fiber parameters on both MM1 and MM2/SM2 (fiber ports). This
will ensure the most optimal connection parameters will be in
effect. If connecting to another Perle media converter, this
parameter should be set to Auto.
Off: Fiber negotiation on both fiber ports will be disabled. Fiber
Negotiation should only be turned off, if the fiber link partner does
not support fiber link negotiations.
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
6
Link Mode (Switch 2)
Switch Position
Mode
Up (default) Smart Link Pass-Through Mode
Down Standard Mode
Smart Link Pass-Through: In this mode, the link state on one
connection is directly reflected through the Media Converter to the
other connection. If link is lost on one of the connections, then the
other link will be brought down.
Standard Mode: In this mode the links can be brought up and
down independently of each other. A loss of link on either fiber
connection can occur without affecting the other connection.
Fiber Fault Alert (Switch 3)
Switch Position
Mode
Up (default) Enabled
Down Disabled
Enabled: If the media converter module detects a loss of fiber
signal on the fiber receiver, the media module will immediately
disable its fiber transmitter signal on this port. This, in effect,
notifies the fiber link partner that an error condition exists on the
fiber connection.
If the remote media converter module is set up for Fiber Fault
Alert(FFA) Enabled and the local media converter is set up with
Smart Link Pass-Through, a loss of fiber link on either the transmit
or receive line will be passed through to the other fiber connection.
Disabled: The media converter module will not monitor for fiber
fault.
Note: This feature is not required; if Fiber negotiation has been
enabled since link negotiation accomplishes the same thing. When
Fiber Negotiation is enabled this switch is ignored.
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
7
Illustration of the FFA
Media Converter A Configuration
Link Mode–Standard Mode
Fiber Fault Alert
Media Converter B Configuration
Link Mode–Smart Link Pass Through Mode
Fiber Fault Alert
Sequence of Events
1. Media Converter Aloses fiber connection (RX) on MM2/SM2.
2. Media Converter Adisables the transmitter (TX) MM2/SM2.
3. Media Converter Bdetects loss of fiber link on receiver RX –
MM2/SM2.
4. Media Converter Bturns off transmitter (TX) on MM1.
5. Media Converter AMM1 is not affected
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
8
Remote Loopback Fiber 1 (Switch 4)
Switch Position
Mode
Up (default) Disabled
Down Enabled
Disabled: The loopback feature is disabled. This is the normal
position for regular operation. The switch must be set to this
position in order for data to pass through the Media Converter
Module.
Enabled: This is a test mode. All data received on the receive
(RX) fiber connection is looped back to the transmit (TX) fiber
connection.
Note: Only one fiber interface can be in loopback at a time.
Remote Loopback Fiber 2 (Switch 5
Switch Position
Mode
Up (default) Disabled
Down Enabled
Disabled: The loopback feature is disabled. This is the normal
position for regular operation. The switch must be set to this
position in order for data to pass through the Media Converter
Module.
Enabled: This is a test mode. All data received on the receive
(RX) fiber connection is looped back to the transmit (TX) fiber
connection.
Note: Only one fiber interface can be in loopback at a time.
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
9
Installing Media Converter Modules
Caution: Observe electrostatic discharge precautions when
installing the Media Converter Module(s) into the Chassis. Failure
to observe this caution could result in damage to the Module(s)
and/or chassis.
The Perle Media Converter Modules can be installed in any
available slot and in any order within the chassis.
1. Remove the Module from its packaging.
2. Using a cross-head screwdriver, remove the screw holding the
face plate to the Chassis to reveal the slot opening.
3. Set the jumpers and DIP switches on the Media Converter
Module to the desired operating mode.(optional)
4. Locate the top and bottom alignment guides inside the MCR
Chassis.
5. Using the module alignment guides gently slide the module
into the slot until it becomes flush with the front of the Chassis.
Light pressure may be needed to seat the module. Do not
force the module as you might cause damage. If there is
resistance, remove the module and check the module
connector for damaged or incorrectly aligned pins. If these are
not damaged, retry module insertion.
6. Tighten the captive retainer screw to ensure the Media
Converter Module is locked in place.
7. Remove the dust cap from the fiber connector and connect the
fiber and copper cables.
Gigabit Fiber to Fiber Media Converter Module – nstallation Guide
10
Removing Media Convert Modules
1. Loosen the captive retainer screw on the front of the Media
Converter Module and gently pull the module out.
2. If not inserting a replacement Media Converter Module then
cover the opening slot with a face plate and secure the screw.
Installing the Duplex Fiber Cable
1. Locate a 1000Base-X compliant duplex (2 strands) fiber cable
with appropriate connectors.
2. Connect the fiber cables from one Converter to the other
Converter/switch/fiber device ensuring that the RX and TX are
reversed at the opposite end.
Installing the Simplex Fiber Cable
1. Locate a 1000Base-X compliant simplex (1 strand) fiber cable
with appropriate connectors.
2. Connect the fiber cable from one Converter to the other
Converter/switch/fiber device.
Este manual sirve para los siguientes modelos
35
Tabla de contenidos
Otros manuales de Convertidor de medios de Perle
Perle
Perle MCR200 Manual de usuario
Perle
Perle S-1110P Manual de usuario
Perle
Perle S-1110HP-XT Manual de usuario
Perle
Perle S-110-P Manual de usuario
Perle
Perle S-10GT-SFP Manual de usuario
Perle
Perle S-110-P Manual de usuario
Perle
Perle C-1110-XXXXX Manual de usuario
Perle
Perle C-10GRT-SFP Manual de usuario
Perle
Perle C-10GT-SFP Manual de usuario
Perle
Perle S-1000-SFP Manual de usuario
Perle
Perle S-10GRT-SFP Manual de usuario
Perle
Perle S-1110P Manual de usuario
Perle
Perle MCR1900 Manual de usuario
Perle
Perle C-110-M2ST2 Manual de usuario
Perle
Perle S-4GPT-DSFP Manual de usuario
Perle
Perle C-1110 Series Manual de usuario
Perle
Perle SMI Media Converter Manual de usuario
Perle
Perle SMI Media Converter Manual de usuario
Perle
Perle SMI Media Converter Manual de usuario
Perle
Perle C-10G-STS Manual de usuario
