PerkinElmer Lambda 265 Manual de programación

09931294C

PerkinElmer, 710 Bridgeport Avenue,

Shelton, CT 06484-4794, U.S.A

Produced in the USA.

Lambda 265, 365 and 465 Automatic Magnetic Stirrer

Assembly Installation Instructions

This instruction sheet describes the installation of this accessory which is used with the Lambda 265, 365

and 465 Spectrophotometer.

NOTE:

Read these instructions before you install this accessory.

Contacting PerkinElmer

Supplies, replacement parts, and accessories can be ordered directly from PerkinElmer, using the part

numbers.

See our website:

http://perkinelmer.com

PerkinElmer's catalog service offers a full selection of high-quality supplies.

To place an order for supplies and many replacement parts, request a free catalog, or ask for information:

If you are located within the U.S., call toll free 1-800-762-4002, 8 a.m. to 8 p.m. EST. Your order will be

shipped promptly, usually within 24 hours.

If you are located outside of the U.S., call your local PerkinElmer sales or service office.

Features

•Easy to install

•Stirring bar rotating evenly at variable speed

•Vertical mixing

•Ideal for small to medium stirring volumes of low-viscosity liquids

•Two channel stirring available

Figure 1 Magnetic Stirrer Control Unit [P/N: N4101016]

09931294C

Dimensions and Specifications

Description

Front of the Control Unit

Figure 2 Front of the Control Unit

(1) The ON/OFF key for the magnetic stirrer:

Press the ON/OFF key to turn the control unit on or off.

(2) The MODE-key for power adjustment of the magnetic stirrer

NOTE:

For the operation, the power settings should be set to 25%.

(3) The display for the speed indicator and the power indicator

(4) MINUS-key for reducing the stirrer speed

(5) PLUS-key for increasing the stirrer speed

Physical Characteristic Specification

Dimensions (mm) 200 (W) x 155 (D) x 380 (H)

Weight (kg) 1.4

Speed (rpm) 100 ~ 1,600

Stirring Power (W) 20

Operating Condition 0 ~ 40℃, 80% Humidity

Power AC 100-240 V / 50-60Hz / 1.5 A

09931294C

Rear of the Control Unit

Figure 3 Rear of the Control Unit

(1) Power switch

(2) Power socket

(3) Socket for DistriBox 4 cable

Configuration of the Magnetic Stirrer Assembly

•Control Unit

•DistriBOX 4

•Stirrer Control Cable, 2ea

•Power Cord, 3ea

Figure 4 Magnetic Stirrer Assembly

09931294C

Compatible Lambda 265 Cell Holders to Magnetic Stirrer Assembly

Accessory Drawing

Single Cell Holder

Water Jacketed

Single Cell Holder

Compatible Lambda 365 Cell Holders to Magnetic Stirrer Assembly

Accessory Drawing

Single Cell Holder

Water Jacketed

Single Cell Holder

Micro Cell Holder

09931294C

Compatible Lambda 465 Cell Holders to Magnetic Stirrer Assembly

Accessory Drawing

Single Cell Holder

(Upon request)

Water Jacketed

Single Cell Holder

(Upon request)

8 Cell Water Jacketed Cell

Changer

Water Jacketed Automatic

Referencing Stage

Where, the cell holder will be modified to be connected with the magnetic stirrer only upon

request.

09931294C

Lambda 265 Installation

NOTE:

The maximum ambient temperature is 50ºC in air and water immersed. The operation with over 50 ºC

temperature will damage the stirrer head.

NOTE:

The Power Setting for setting the DistriBox4to 25. Whenever turning the main switch on or off, you

should set the power to 25. [The default power set is 50]

NOTE:

Two stirrer control cables should be connected via the DistriBOX4.

NOTE:

Stirrers should be connected in pairs: [Position 1+1B] or [Position 2+2B]. The single stirring connection is

not supported.

CAUTION

ATTENTION

Make sure the instrument is turned off while installing this accessory.

Assurez-vous que l’instrument est éteint lors de l’installation de cet

accessoire.

Figure 5 Connecting Stirrers (Two stirrer heads should be connected in pairs)

09931294C

1. Connect the power cable to the control unit.

Figure 6 Connecting the power cable

2. Connect the distriBOX4 to the socket for the stirrer control cable.

Figure 7 Connecting the distriBOX4

Connect to the Single / Water Jacketed Single Cell Holder

1. Connect two stirrer control cables to the 4-pin socket of the distriBOX4.

Figure 8 Connecting two stirrer control cables

09931294C

2. Using the M3 wrench, remove the screw in the single cell holder and disassemble the holder.

Figure 9 Removing the screw

3. Insert the stirrer head of the stirrer control cable into the single cell holder.

Figure 10 Inserting the Stirrer head

4. Assemble the single cell holder with the stirrer head inserted, and tighten the screw using the M3

wrench.

Figure 11 Stirrer head inserted

09931294C

5. Press the ON/OFF key to turn on the control unit. When the stirrer speed is displayed, adjust the

desired stirrer speed by using the MINUS-key and PLUS-key.

Figure 12 Pressing the MINUS-key & PLUS-key

NOTE:

When you press the mode key, power adjustment mode is displayed. The power settings should be set to

P 25.

NOTE:

The default power set is 50. Whenever turning the main switch on or off, set the power to 25.

Figure 13 Power Setting

09931294C

Lambda 365 Installation

NOTE:

The maximum ambient temperature is 50ºC in air and water immersed. The operation with over 50 ºC

temperature will damage the stirrer head.

NOTE:

The Power Setting for setting the DistriBox4to 25. Whenever turning the main switch on or off, you

should set the power to 25. [The default power set is 50]

NOTE:

Two stirrer control cables should be connected via the DistriBOX4.

NOTE:

Stirrers should be connected in pairs: [Position 1+1B] or [Position 2+2B]. The single stirring connection is

not supported.

CAUTION

ATTENTION

Make sure the instrument is turned off while installing this accessory.

Assurez-vous que l’instrument est éteint lors de l’installation de cet

accessoire.

Figure 14 Connecting Stirrers (Two stirrer heads should be connected in pairs)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de PerkinElmer

PerkinElmer

PerkinElmer Lambda 365 Manual de usuario

PerkinElmer

PerkinElmer Lambda 365 Manual de usuario

PerkinElmer

PerkinElmer FL 8500 Manual de usuario

PerkinElmer

PerkinElmer FX-10 UHPLC Manual de usuario

PerkinElmer

PerkinElmer LAMBDA 265 Manual de usuario

PerkinElmer

PerkinElmer Lambda 365 Fiber Coupling Module Manual de usuario

PerkinElmer

PerkinElmer FL 6500 Manual de usuario

PerkinElmer

PerkinElmer L6050002B Manual de usuario

PerkinElmer

PerkinElmer LabChip GX Manual de usuario

PerkinElmer

PerkinElmer FL 6500 Manual de usuario

PerkinElmer

PerkinElmer Lambda 365 Manual de usuario

PerkinElmer

PerkinElmer AAnalyst 300 Manual de usuario

PerkinElmer

PerkinElmer Spectrum 100 Series Manual de usuario

PerkinElmer

PerkinElmer AAnalyst 300 Manual de usuario

PerkinElmer

PerkinElmer DSC 4000 Instrucciones de montaje

PerkinElmer

PerkinElmer Lambda 20 Manual del producto

PerkinElmer

PerkinElmer LabChip GX Touch Manual de usuario

PerkinElmer

PerkinElmer DSC 6000 Instrucciones de montaje

PerkinElmer

PerkinElmer Spotlight 400 Series Manual de usuario

PerkinElmer

PerkinElmer Polarizer Holder Manual de usuario

PerkinElmer

PerkinElmer Lambda 465 Manual de usuario

PerkinElmer

PerkinElmer LAMBDA 265 Manual de usuario

PerkinElmer

PerkinElmer Lambda XLS Manual de usuario

PerkinElmer

PerkinElmer Lambda 11 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario