PEERLESS DS-VW760 and assembly Guía
1 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Installation and Assembly:
Full Service Video Wall Mount
Model: DS-VW760
EXTENDED
COLLAPSED
Maximum Load Capacity: 150 Ib ( 68 kg)
2 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Table of Contents
Horizontal and Vertical Video Wall Mount Assembly Formula................................................................................................3
Parts List.................................................................................................................................................................................4
Mounting and Removing Flat Panel Screen...........................................................................................................................8
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Solid Concrete or Cinder Block ........................................................................................................................5
Installing Tilt Brackets.............................................................................................................................................................6
Mounting and Removing Flat Panel Screen
NOTE: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
•drill
• 5/16"(8mm)bitforconcreteandcinderblockwall
• 5/32"(4mm)bitforwoodstudwall
• level
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• Thisproductshouldonlybeinstalledbysomeoneofgoodmechanicalaptitude,hasexperiencewithbasicbuilding
construction, and fully understands these instructions.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattached
hardware and components.
• NeverexceedtheMaximumLoadCapacity.Seepageone.
• Ifmountingtowoodwallstuds,makesurethatmountingscrewsareanchoredintothecenterofthestuds.Useof
an"edgetoedge"studnderishighlyrecommended.
• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• Thisproductisintendedforindooruseonly.Useofthisproductoutdoorscouldleadtoproductfailureandpersonal
injury.
• Thisproductwasdesignedtobeinstalledonthefollowingwallconstructiononly;
WALL CONSTRUCTION HARDWARE REQUIRED
•Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•CinderBlock ContactQualiedProfessional
•MetalStud ContactQualiedProfessional
•Brick ContactQualiedProfessional
•Otherorunsure? ContactQualiedProfessional
WARNING
Accessories
•DS-ACC760 Cable Release Kit
• DS-VWS0## Wall Plate Spacer Kit
3 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Accessories
•DS-ACC760 Cable Release Kit
• DS-VWS0## Wall Plate Spacer Kit
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine vertical spacing.
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine horizontal spacing.
Todetermineedgeofsecondmount,add(Z)toedgeorrstmount.
WIDTH
Vertical Spacing Location
Horizontal Spacing Location
H
Vertical Location
X - 10.25 + (.938 OR 1.688) = (Y1 OR Y2)
DISPLAY WIDTH - (35) = Z (SPACING BETWEEN MOUNTS)
Horizontal Location
DISPLAY WIDTH
DISPLAY
HEIGHT
X
Y2
Y1 .938
1.688 10.25
16.00"
20.00"
24.00"
17.50"Z
Todeterminelowermountingslotpositionofsecondmount,adddisplayheightto(Y1)or(Y2)
4 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Openvideowallmountassemblybyreleasinglockingtab.Pullorpushup
on locking tab.
A
1
B C
D E F G
H I J K
PartsList
Description Qty. Part#
Apulloutmountassembly 1 145‐1104
Badapterbracket2 145‐1105
Clockbracket2 145‐1091
DM5x10mmsocketpintype‐Fscrew 2 520‐1164
E#14x2.5"hexheadwoodscrew4 5S1‐015‐C03
Fconcreteanchor4 590‐0320
Gfenderwasher4 540‐1008
Hnylonshoulderwasher4 590‐2233
IM6x12mmphillipsscrew4 520‐1128
JM8x15mmphillipsscrew4 520‐9257
K4mmallenwrench1 560‐9646
Lcabletie(notshown) 2 560‐9711
Mmeshsleeve(notshown) 1 600‐1014
VIDEOWALL
MOUNTASSEMBLY
PULL UP
PUSH UP
LOCKINGTAB
LOCKINGTAB
5 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Remove display carriage by removing clip, pull release pin, and screws as shown. Remove screws using
4mmallenwrench(K).
2
Removing Display Carriage
LOCKINGTAB
LOCKINGTAB
VIDEOWALL
MOUNTASSEMBLY
DISPLAY CARRIAGE
VIDEOWALL
MOUNTASSEMBLY DISPLAY CARRIAGE
CLIP
RELEASEPIN
SCREWS
EG
Installation to Wall Stud
Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.
Based on their edges, draw a vertical line down the stud center. Place video wall mount assembly on wall as a
template. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on
thestudcenterline.Drillfour5/32"(4mm)dia.holes2-1/2"(65mm)deep.Makesurethatthevideowallmount
assemblyislevel,secureitusingfour#14x2.5"woodscrews(E)andfenderwashers(G)asshownbelow.
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall
attached hardware and components.
• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
3
VIDEOWALL
MOUNTASSEMBLY
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
6 of 14
E
F
G
solid concrete
cinder block
VIDEOWALL
MOUNTASSEMBLY
Installation to Solid Concrete or Cinder Block
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8"(35mm)ofactual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
inasolidpartoftheblock,generally1"(25mm)minimumfromthesideoftheblock.CinderblockmustmeetASTM
C-90specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrilltheholeinsteadofa
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.
• Makesurethatthewallwillsafelysupportfourtimesthecombinedloadoftheequipmentandallattachedhardware
and components.
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
F
Drillholesandinsertanchors(F).
Placeplate(A)overanchors(E)andsecurewithscrews(F).
Tighten all fasteners.
A
F
E
concrete
surface
• Tightenscrewssothatwallplateisrmlyattached,
but do not overtighten.Overtighteningcandamage
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Alwaysattachconcreteexpansionanchorsdirectly
to load-bearing concrete.
• Neverattachconcreteexpansionanchorsto
concrete covered with plaster, drywall, or other
nishingmaterial.Ifmountingtoconcretesurfaces
coveredwithanishingsurfaceisunavoidable,
thenishingsurfacemustbecounterboredas
shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywallisthickerthan5/8"(16mm),custom
fasteners must be supplied by installer
WARNING
Make sure that video wall mount assembly is level,
use it as a template to mark four mounting holes.
Drillfour1/4”(6mm)dia.holestoaminimumdepth
of2.5”(64mm).Insertanchors(F)inholesush
withwallasshown(right).Placevideowallmount
assembly over anchors and secure with four #14
x2.5”screws(E),andfenderwashers(G).Level,
then tighten all fasteners.
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
7 of 14
8 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Secure display carriage by pulling release pin, fastening clevis pin, clip, four screws, and spacer as shown.
NOTE: make sure that spacer is in-between display carriage and video wall mount assembly.
Re-Attaching Display Carriage
4
VIDEOWALL
MOUNTASSEMBLY
DISPLAY CARRIAGE
CLIP
RELEASEPIN
SCREWS
HOLEINPIN
SPACER
CLEVISPIN
Attachadapterbrackets(B)tobackofdisplayusingfourM6x12mmphillipsscrews(I)withnylonshoulderwasher(H),orfour
M8x15mmphillipsscrews(J)asshownbelow.
NOTE: Hardware to attach dedicated plates to the mount are included with the dedicated plates.
B
HI or J
5
400 mm 300 mm 200 mm PLP
MAX VESA-600 mm
MINVESA-200mm
Attaching Adapter Brackets to Display
DISPLAY
9 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
B
B
B
B
6
600 mm
400 mm
300 mm
200 mm
PLP
SECURITY SCREW
Attachadapterbrackets(B)todisplaycarriage.Slideadapterbrackets(B)topositionbasedonholepatternasshownbelow.
Loosely fasten in place using security screw as shown in detail 1.
NOTE:Oncedisplayislocatedindesiredposition,tightensecurityscrewsusing4mmallenwrench(K)tolockinplace.
Attaching Adapter Brackets to Display Carriage
DISPLAY CARRIAGE
DISPLAY CARRIAGE
FRONT
DETAIL 1
OUTSIDEEDGEOF
ADAPTER BRACKET
DETAIL 2
Horizontal Display Position
OPTIONAL GUIDE: When positioning adapter brackets make sure outside edge
of adapter bracket is in notch on display carriage as shown in detail 2.
NOTCH
Screen and adapter brackets can slide along rail to position
screen horizontally.
10 of 14 ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Use legend below to determine position of display.
NOTE: Eachknobcanbeadjustedindependentlyfornetuningadjustments.
7
Turn knob CLOCKWISE to tighten
Turn knob COUNTER-CLOCKWISE to loosen
UP
ROTATE LEFT ROTATE RIGHT
DOWN
Display Carriage Adjustment
Tabla de contenidos
Otros manuales de Rack y soporte de PEERLESS
PEERLESS
PEERLESS Solid-Point PLCM 1 CP Guía
PEERLESS
PEERLESS A100IWBMOUNT Guía
PEERLESS
PEERLESS WSP 490 Guía
PEERLESS
PEERLESS ESA746PU Guía
PEERLESS
PEERLESS SP850-UNLP-GB Guía
PEERLESS
PEERLESS PM 47 Guía
PEERLESS
PEERLESS LCC 18-C Guía
PEERLESS
PEERLESS LCT Series Guía
PEERLESS
PEERLESS IMC 18 Guía
PEERLESS
PEERLESS SA761P Guía
PEERLESS
PEERLESS PARAMOUNT PF640 Guía
PEERLESS
PEERLESS SR1G Guía
PEERLESS
PEERLESS Solid-Point PLCM UN1 Guía
PEERLESS
PEERLESS PED 410 Guía
PEERLESS
PEERLESS Paramount PS200 Guía
PEERLESS
PEERLESS SF630P-S and assembly Guía
PEERLESS
PEERLESS PJF2-UNV Guía
PEERLESS
PEERLESS SmartMount SF650 Guía
PEERLESS
PEERLESS DS 35 Guía
PEERLESS
PEERLESS CMJ 470W Guía
