PEERLESS COL 510P Guía
ISSUED: 11-24-99 SHEET #: 200-9192-2 07-23-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 6
L
PARTSLIST
PART # QTY. DESCRIPTION
A200-1106 1 support column (model COL 510P only)
200-1107 (model COL 610P only)
200-1108 (model COL 710P only)
200-1109 (model COL 810P only)
B120-0041 1 base plate
C1390-472 3 fastener plate
D5S1-M10-A20 6 M10-1.5 x 20 mm socket head screw
E540-9424 6 lock washer
F540-9407 14 flat washer
G530-9401 2 rubber grommet
H5M9-381-H03 6 concrete expansion anchor
I560-9646 1 4 mm security allen wrench
J200-1096 1 tilt bracket
K200-1095 1 tube support
L200-1094 1 adapter mount
M200-1093 1 swivel bracket
N200-1517 1 neck tube
O590-1111 1 column bushing
P520-9263 16 M10 x 1.5 x 15 mm penta pin screw
Q530-9310 2 3/8 x 16 nylock nut
R520-1015 2 3/8 x 16 x 3" socket screw bolt
T520-1065 2 M5 x .8 x 20 mm socket pin screw
U520-9260 1 M10 penta pin tool
V520-9525 3 M8 x 1.25 x 12 mm socket head screw
W530-9306 1 5/16-18 nylock nut
X500-1082 1 5/16-18 x 3/8 shoulder bolt screw
Y540-9454 2 3/8 x 3/4 x 1/8 flat washer
Installation and Assembly - Support Column's
for Flat Panel Pedestal Mounts
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
B
Parts List
A
Before you start make sure all parts listed are included with your product.
Some parts may appear slightly different than illustrated.
Models:COL 510P, COL 610P,
COL 710P, COL810P
J
XYW MKO
N
T
R
Q
E
H
G
C
D
F
P
U
I
V
ISSUED: 11-24-99 SHEET #: 200-9192-2 07-23-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 6
O
A
F
E
D
H
A
C
B
Attach column bushing (O) to support column (A) using two
screws (T). The screws control swivel action, so do not
tighten until product is fully assembled and flat panel is in
viewing position.
Insert rubber grommet (G) into hole in bottom of support
column (A).
At all three support legs attach support column (A) to base
plate (B) using fastener plates (C), M10-1.5 x 20 mm
socket head screws (D), lock washers (E), and flat
washers (F). Note: Leave screws slightly loose until all are
attached, then tighten all screws securely.
Attach base plate (B) to concrete floor. Use six Rawl-Bolt
concrete expansion anchors (H). Drill 3/8" dia. holes to a
minimum depth of 2".
G
T
• Flat panel weight is restricted to a maximum of 150 lb
(68 kg). Interfacing flat panel into electrical system at
installation site must conform to local electrical codes
governingsuchinstallationsandbe done bya qualified
electrician / electrical contractor.
• Installermustverify that mountingsurface will safely
supportthe combined weightofall attached equipment
andhardware.
WARNING
• For attachment to concrete floor only!All six concrete
expansion anchors must be used.
• Tighten to 420 IN • LB (47.6 N.M.) torque.
WARNING
ISSUED: 11-24-99 SHEET #: 200-9192-2 07-23-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 6
Attach tilt bracket (J) to tube support (K)
with four screws (P) using penta pin
tool (U).
Insert four screws and washers (P & F)
into tilt bracket (J). Do not fully tighten.
Leave 1/4" of exposed thread between
tilt bracket (J) and washers (F).
Q
K
N
J
P
K
Attach tube support (K) to neck
tube (N) using two screw bolts
(R), nuts (Q), and washers (F)
as shown. Insert rubber
grommet (G) into neck tube (N).
P
F
1/4"EXPOSED
THREAD
G
F
F
R
ISSUED: 11-24-99 SHEET #: 200-9192-2 07-23-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 6
Attach adapter mount (L) to adapter bracket (purchased separately and may
appear different than illustrated) with eight screws (P) shown right. Attach
swivel bracket (M) to adapter mount (L) using shoulder bolt (X), washers (Y),
and nut (W) as shown below.
FOR HORIZONTAL MOUNT: secure with three screws (V) shown below left.
FOR VERTICAL MOUNT: secure with three screws (V) shown below right.
ML
X
Y
YW
V
SLOT
V
L
P
ADAPTER
BRACKET
ISSUED: 11-24-99 SHEET #: 200-9192-2 07-23-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 6
Hook swivel bracket (M) onto tilt bracket (J). Adjust tilt
(0° to 15°) and tighten screws (P) using penta pin
tool (U).
Adjust swivel and tighten two screws (T) securing
neck tube (N).
J
N
T
ADAPTER BRACKET AND FLAT
PANEL MAY APPEAR SLIGHTLY
DIFFERENT THAN ILLUSTRATED.
360° SWIVEL
P
M
ISSUED: 11-24-99 SHEET #: 200-9192-2 07-23-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
6 of 6
OPTIONAL: To rotate flat panel 90° without detaching
swivel bracket (M), follow detail one through detail three.
REMOVETWO
SCREWS (V).
ROTATEMONITOR
90° AND TIGHTEN
SCREW (V).
INSERT AND
TIGHTENTWO
SCREWS (V).
DETAIL 3
DETAIL 1
DETAIL 2
LOOSEN
SCREW (V).
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
M
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Rack y soporte de PEERLESS
PEERLESS
PEERLESS Paramount PRT2X2 Manual de usuario
PEERLESS
PEERLESS IM760P Guía
PEERLESS
PEERLESS IM740P Guía
PEERLESS
PEERLESS Solid-Point PLCM UN1 Guía
PEERLESS
PEERLESS SP850-UNLP-GB Guía
PEERLESS
PEERLESS SPK 811W Manual de usuario
PEERLESS
PEERLESS SmartMount D-FPF-320 Guía
PEERLESS
PEERLESS ACC951 Guía
PEERLESS
PEERLESS PARAMOUNT PA730 Manual de instrucciones
PEERLESS
PEERLESS Solid-Point PLCM 2 Guía
PEERLESS
PEERLESS SUT632P Guía
PEERLESS
PEERLESS WBK100-W Guía
PEERLESS
PEERLESS HDS-S Guía
PEERLESS
PEERLESS PJF2-UNV Guía
PEERLESS
PEERLESS JMWS 30 Guía
PEERLESS
PEERLESS SOLID POINT PLCM 1 Manual de instrucciones
PEERLESS
PEERLESS SUF640P and assembly Guía
PEERLESS
PEERLESS LCC 18 Guía
PEERLESS
PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Guía
PEERLESS
PEERLESS LDS 1920U Guía
