PEERLESS Solid-Point PLCM 2 Guía
ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 5
Read instruction sheet before you start installation and assembly.
Model:PLCM 2
Maximum Load Capacity:
225 lb (102.3 kg)
Installation and Assembly -Solid•Point™Flat Panel
Straight Column Mount
TABLE OF CONTENTS
Installations
InstallingPLCM2to ceiling.........................page 3
Applications
Installation of plasma screens and
30" or larger LCD screens.......................... page 4
Installation of small LCD screens............... page 5
• Installer must verify that the wall will safely support the
combinedweightofallattachedequipmentand
hardware.
WARNING
ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 5
Description Qty Part #
Aceiling arm box 1 201-1062
Btilt bracket 1 200-1552
Dretaining collar 1 1800-375
EM5 x .8 x 10mm penta-pin™screw 4 505-9010
F2.875 OD x 2.125 ID x .062 H fiber washer 1 540-9432
GM10 x 1.5 x 15 mm penta-pin screw 8 520-9263
HM10 x 2" penta-pin tool 1 520-9260
IM5 x 1" penta-pin tool 1 520-9249
JM5 x .8 x 8 mm phillips Type F screw 4 520-1167
Before you begin, make sure all parts shown are included with your product.
PARTS LIST
D
F
A
B
Note: Some parts may not appear exactly as illustrated.
HI
E
G
J
Fasteners
ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 5
ceiling plate (not included)
Threadsupportpipe(notincluded)intothreadedfittinginceilingplate(notincluded).Tighten-fourorfivecomplete
turns - leaving slot aligned with one small hole in the side of the ceiling plate threaded fitting. Insert and tighten one
M5 x .8 x 10 mm penta-pin screw provided with ceiling plate as shown. Use the M5 penta-pin tool (I) to tighten
screw. BY HAND, insert four M10 x 1.5 x 15 mm penta-pin screws (G) into threaded holes in the sides of ceiling
armbox(A).Leave approximately1/4" ofexposed thread.Slideceilingarmbox(A)andfiberwasher(F)ontoend
ofsupportpipe.Threadretainingcollar(D)ontothreadedendofsupportpipe. Tighten-fourorfivecompleteturns.
Slide ceiling arm box (A) down so that it is on top of retaining collar (D). Insert and tighten one M5 x .8 x 10 mm
penta-pinscrew(E) intoretaining collar(D)as shown. Insertone M5penta-pinscrew (E)through thetabon the
back of ceiling arm box (A). Use M5 penta-pin tool (I) to tighten screw just enough to stabilize support pipe.
Note: ADJ or EXT extension columns can be used in combination with, or in place of support pipe to achieve
differentlengths.
E
D
A
F
D
G
1/4"
G
E
M5 screw
BACKOF CEILING
ARMBOX
support pipe (not included)
ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 5
Hang tilt bracket (B) onto ceiling arm box (A).
Adjust tilt as desired and tighten four M10 x 1.5 x
15 mm penta-pin screws (G) securely using M10
penta-pintool (H).
B
A
G
Attach tilt bracket (B) to adapter plate using four M10 x 15 mm penta-pin screws (G) in accordance with appropri-
atedrawingbelow.Tighten usingM10 penta-pintool(H).
G
B
Note: Refertoadapter plateinstruction sheetforattachment ofadapter platetoplasma before proceedingwith step2.
LANDSCAPE
LANDSCAPE PORTRAIT
LANDSCAPE PORTRAIT
B
A
G
B
G
ADAPTERPLATE
ADAPTERPLATE
PLASMASCREEN
PLASMASCREEN
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING
ISSUED:02-14-03 SHEET #: 201-9019-7 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 5
ADAPTERBRACKET
B
J
Attach tilt bracket (B) to adapter bracket using four M5 x 8 mm phillips screws (J).
Note: Do not use M5 x 6 mm screws that are included with the adapter bracket.
Note: Refertoadapterbracketinstruction sheetfor attachmentof adapterbrackettoLCDscreen beforeproceeding with
step 2.
Hang tilt bracket (B) onto ceiling arm box (A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G) securely using M10 penta-pin tool (H).
B
A
G
©2004Peerless Industries,Inc. All rightsreserved.
Peerlessis aregistered trademarkof PeerlessIndustries,Inc.
Solid•Pointis atrademarkofPeerlessIndustries, Inc.
Allother brand andproduct namesare trademarksorregistered trademarksof theirrespective owners.
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
LCDSCREEN
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING
Tabla de contenidos
Otros manuales de Rack y soporte de PEERLESS
PEERLESS
PEERLESS PARAMOUNT PSP2-S Guía
PEERLESS
PEERLESS RTLA-100 Guía
PEERLESS
PEERLESS PJF2-UNV Guía
PEERLESS
PEERLESS PLC Guía
PEERLESS
PEERLESS PLCM 3 Guía
PEERLESS
PEERLESS ACC605 Guía
PEERLESS
PEERLESS Paramount PA760 Guía
PEERLESS
PEERLESS ACC951 Guía
PEERLESS
PEERLESS SAL730P Guía
PEERLESS
PEERLESS SMARTMOUNT SCS221 Guía
PEERLESS
PEERLESS MIS 213 Guía
PEERLESS
PEERLESS SA761P Guía
PEERLESS
PEERLESS PED 410 Guía
PEERLESS
PEERLESS PWS211 Guía
PEERLESS
PEERLESS LDS 1920U Guía
PEERLESS
PEERLESS PARAMOUNT PT650 and assembly Guía
PEERLESS
PEERLESS SUF650P and assembly Guía
PEERLESS
PEERLESS DST940 Guía
PEERLESS
PEERLESS DS-VW760 and assembly Guía
PEERLESS
PEERLESS SF630P-S and assembly Guía
