PEERLESS Mounts PLA 50-UNL Guía

Models: PLA 50-UNL, PLA 50-UNL-S,

PLA 50-UNLP, PLA 50-UNLP-S,

RTPLA 50,RTPLA 50-S

Installation and Assembly - Universal Articulating

SwivelArm for 32" - 50" Plasma Screens

Maximum UL Load Capacity:150 lb (68 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

2 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

Read instruction sheet before you start installation and assembly.

Installations:

To Wood Stud Walls ...................................................................................................... page 6

To Concrete Walls .......................................................................................................... page 7

IMPORTANT! Turn to the appropriate page for your wall installation.

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings

containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please

callPeerlesscustomercareat1-800-729-0307.

• Thisproduct should only be installed by a qualified professional.

• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

• Neverexceed the Maximum UL Load Capacity of 150 lb (68 kg).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrewsand nutsfirmly, but do not overtighten. Overtightening can damagetheitems, greatly reducing their

holdingpower.

WARNING

Tools Needed for Assembly

•studfinder ("edge to edge" stud finder is recommended)

•drill

•3/16" drill bit for wood studs

•5/16" masonry drill bit for concrete

•7/16"socketwrenchwithextension(recommended)

• 10 mm socket wrench for concrete anchors

•level

•phillipsscrewdriver

WALLCONSTRUCTION ADDITIONAL HARDWARE REQUIRED

Wood Stud, Wood Beam none

Concrete none

Metal stud WSP716, WSP716-S, WSP724, or WSP724-S

Other or unsure? Contact Customer Care

IMPORTANT! Certain types of walls require additional mounting hardware...

Accessories

•External Wall Plate (WSP716, WSP716-S, WSP724,WSP724-S)

(MetalStudnotevaluatedbyUL)

3 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

MODEL MODEL

PLA50-UNL RTPLA50-S

PLA50-UNLP PLA50-UNL-S

RTPLA 50 PLA 50-UNLP-S

DESCRIPTION QTY. PART# PART#

Awallplate 1 201-1095 201-4095

Btilt-roll assembly 1 201-1093 201-4093

Carmassembly 1 201-1094 201-4094

Dwallsupport arm axle 1 201-1041 201-1041

Evinyltrim 3 600-1012 600-1012

FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262

G.505 x .75 x .062" nylon washer 1 540-1074 540-1074

Htilt adjustment knob 1 560-0108 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315

J1.525 x 2 x .062" delrin washer 2 540-1070 540-1070

K#8-32 x .375" socket head cap screw 1 520-1210 520-1210

Lplastic finishing cap 8 590-1123 590-1123

Mholdingpin 1 580-1166 580-1166

Nretainerplug 1 590-1007 590-1007

O5/16 x 3" wood screw 6 520-1243 520-1243

P.250 x 1 x .068" washer 6 540-1063 540-1063

Q9/64"allenwrench 1 560-9728 560-9728

Rcablemanagementclips 4 590-1166 590-1166

Scable tie 4 590-1168 590-1168

T36"polyestermeshsleeve 1 600-1015 600-1015

U6 mm allen wrench 1 560-9716 560-9716

Wanchor 6 590-1025 590-1025

Before you start make sure all parts

listed are included with your product.

Wall Mount Parts List A

Some parts may appear slightly different than illustrated.

M N

S T

JI K L

4 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

PLA 50-UNL PLA 50-UNL-S PLA 50-UNLP PLA 50-UNLP-S

Description Qty Part # Part # Part # Part #

AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110

BB shallow adapter bracket 2 200-0756 200-0757 200-0754 200-0755

CC deep adapter bracket 2 200-0752 200-0753 200-0750 200-0751

DD allen wrench 1 560-9646 560-9646 560-0072 560-0072

Before you begin, make sure all parts shown are included with your product.

Adapter Bracket Parts List

RTPLA50-S

RTPLA50

5 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

M5 x 25 mm (4)

520-1122

M4 x 12 mm (6)

510-1079

M4 x 25 mm (4)

510-1082

M5 x 12 mm (4)

520-1064 M6 x 12 mm (4)

520-1050

M6 x 25 mm (4)

520-1211

I.D. 5.6 mm (4)

540-1057

multi-washer(6)

580-1036

I.D. 8.7 mm (4)

540-1059

SecurityAdapter Bracket Fasteners

M6 x 20 mm (4)

520-9554

M6 x 30 mm (4)

520-1067

M8 x 15 mm (6)

520-1068

M8 x 40 mm (4)

520-1152

M8 x 25 mm (4)

520-1101

M6 x 20 mm (4)

520-9402

M6 x 30 mm (4)

510-9109 multi-washer(6)

580-1036

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

M4 x 12 mm (6)

504-9013

Phillips Adapter Bracket Fasteners

M4 x 25 mm (4)

504-1015

M5 x 12 mm (4)

520-1027 M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208

I.D. 5.6 mm (4)

540-1057

M8 x 25 mm (4)

520-1031

I.D. 8.7 mm (4)

540-1059

6 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

• Installermust verify that the supporting surface will safely support the combined load of the equipmentandallattached

hardwareandcomponents.

• Tightenwood screws so that wall plate is firmly attached, but donotovertighten. Overtightening can damage the

screws,greatly reducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment of mount throughstandardthickness drywall or plaster into woodstuds.Installers

areresponsible to providehardwarefor other types ofmounting situations.

• Neverexceed the Maximum Load Capacity of 150 lb (68 kg).

WARNING

Installation to Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useof an edge-to-edge stud finder is highly recommended. Based on their edges, draw a verticalline down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be located 3.9" below the

desired screen center. Level plate, and mark the center of the four mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill six 3/16" (5 mm) dia. holes 3" (76 mm) deep. Make sure that the wall plate is

level, secure it using six 5/16 x 3" wood screws (O) and washers (P).

Skip to step 2 on page 8.

• Never mount this product to metal studs without the

requiredaccessory.

WARNING

7 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

Make sure that wall plate (A) is level, use it as a tem-

plate to mark six mounting holes. The top mounting slots

should be located 3.9" below the desired screen center.

Use the masonry bit to drill six 5/16" (8 mm) dia. holes to

a minimum depth of 1.75" (45 mm). Attach wall plate (A)

using concrete anchors (W) and washers (P) as shown in

1-1through1-4.

Align hole in wall plate (A) with hole in wall. Gently

hammerin concrete anchor as shown.

Usea 10 mm wrench (not provided) to tightenconcrete

anchors (W) to 80 in • lb(9 N.M.) maximum torque as

shown.

1-1

1-2

1-1

1-3

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattach concrete expansion anchors toconcrete

coveredwith plaster, drywall,or other finishing mate-

rial.

WARNING

• Tightenconcreteanchor bolt firmly,but donotover-

tighten.Overtightening can damage thebolt,greatly

reducingits holdingpower.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

• Neverexceed the Maximum Load Capacity of 150 lb (68 kg).

Installation to Concrete Wall

1-4

1-2

CUTAWAYVIEW

INCORRECT CORRECT

mounting

plate

plaster/

drywall

concrete mounting

plate concrete

plaster/

drywall

concrete

surface

Drill hole(s) and insert anchor(s) (W)

mounting

plate

Place plate over anchor(s) (W) and secure with screw(s)(O)

Tighten all fasteners

8 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown.Cable ties (S) are used with

clipsfor cord management.

Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.

Note: There are five mounting positions. The

center position is shown (right). Slidewasher (J)

over wall support arm axle (D). Next, insert plastic

cap (N) into axle. Then, insert holding pin (M) into

axle. See detail 1.

Note: Fit of axle (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

2-1

3-1

Insert socket cap screw (K) into hole at bottom of

wall support arm axle (D) as shown in detail 3.

Tightenscrew using 9/64" allen wrench(Q).

DETAIL 3

ADETAIL 1

Place arm assembly (C) with washer (J) into wall

plate (A). Insert axle assembly shown in detail 1

throughwall plate (A), arm assembly (C),and

washer (J). Lock axle in place by aligning holding

pin (M) with notches shown in detail 2.

2-2 NOTCH

DETAIL 2

• If you are uncertain that product is properly installed, call customer care.

WARNING

9 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).Attach tilt-roll assembly to adapter bracket

(AA) with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

• Donot overtightenscrews! Overtighteningmay hinder

rolloption.

CAUTION

Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm

assembly(C).

4-1 Insertonefinishingcap(L)intoeachunusedholeof wall plate (A).

SWIVELBOX

10 of 39 ISSUED: 06-05-06 SHEET #: 202-9140-5 12-12-06

Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.

Hook tilt-roll assembly (B) onto M10 screws (F).

Insert carriage bolt (I) into slot of swivel box as

shown in figure 6.1. Install nylon washer (G) and tilt

adjustmentknob (H).

Install remaining two M10 screws (F) as shown in

figure6.2. HAND TIGHTENallfour M10 screwsto

allowfor tilt adjustment. Removetape from carriage

bolt (I). For tilt adjustment, push back on the top of

plasma to relieve pressure on knob.Adjust tilt to

desired position and tighten tilt adjustment knob (H),

then securely tighten all four M10 screws (F) using 6

mmallen wrench (U).

.25"

• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.

WARNING

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

6-1

6-2

fig 6.1 fig 6.2

SWIVELBOX

SWIVELBOX C

Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Rack y soporte de PEERLESS Mounts

PEERLESS Mounts

PEERLESS Mounts SmartMount SA740P Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B4C Guía

PEERLESS Mounts

PEERLESS Mounts Vector Pro II PJF2-UNV Series Guía

PEERLESS Mounts

PEERLESS Mounts PRG UNV Guía

PEERLESS Mounts

PEERLESS Mounts DS-VL-H072 Guía

PEERLESS Mounts

PEERLESS Mounts FPECMC-01 Guía

PEERLESS Mounts

PEERLESS Mounts SUT660P Guía

PEERLESS Mounts

PEERLESS Mounts RTLA-100 Guía

PEERLESS Mounts

PEERLESS Mounts SmartMount ST630P Guía

PEERLESS Mounts

PEERLESS Mounts ACC328 Guía

PEERLESS Mounts

PEERLESS Mounts Smartmount D-FPF-220 Guía

PEERLESS Mounts

PEERLESS Mounts DS-VL-H060 Guía

PEERLESS Mounts

PEERLESS Mounts PLAV 70-UNL Guía

PEERLESS Mounts

PEERLESS Mounts ACC488 Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3H Guía

PEERLESS Mounts

PEERLESS Mounts Smartmount D-FPF-220 Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3C Guía

PEERLESS Mounts

PEERLESS Mounts DS-VL-H048 Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B1C Guía

PEERLESS Mounts

PEERLESS Mounts SmartMount ST632P Guía

PEERLESS Mounts

PEERLESS Mounts PLAV70-UNLP-GB Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B2H Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B6C Guía

PEERLESS Mounts

PEERLESS Mounts ACC 310 Guía

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario