PEERLESS Mounts PLAV 70-UNL Guía

Models: PLAV 70-UNL, PLAV 70-UNL-S

PLAV 70-UNLP, PLAV 70-UNLP-S

Installation and Assembly - Universal Articulating

Swivel Double-Arm for 42" - 60" Plasma Screens

Maximum UL Load Capacity:200 lb (91 kg)

This product is UL Listed. It must be

installed by a qualified professional

installer.

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

2 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

Read instruction sheet before you start installation and assembly.

IMPORTANT! Turn to the appropriate page for your wall installation.

• Donot begin to install yourPeerless product until you haveread and understood the instructionsand warnings

containedin this Installation Sheet. Ifyou have any questions regardinganyof the instructions orwarnings,please

callPeerlesscustomercareat1-800-729-0307.

• Thisproductshould only be installed by aqualifiedprofessional.

• Makesure that the supportingsurface will safely supportthe combined load ofthe equipment and allattached hard-

wareandcomponents.

• Neverexceedthe Maximum Load Capacity of 200lb(91 kg).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finder is highlyrecommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews and nutsfirmly, but do not overtighten. Overtighteningcandamagethe items, greatly reducing their

holdingpower.

WARNING

Installations:

To Wood Stud Walls ...................................................................................................... page 6

To Concrete Walls .......................................................................................................... page 7

Tools Needed for Assembly

•studfinder ("edge to edge"stud finder is recommended)

•drill

•7/32" drill bit for wood studs

•5/16" masonry drill bit for concrete

•7/16"socket wrench with extension (recommended)

•level

•phillipsscrewdriver

•3/4"open-endwrench

Accessories

•External Wall Plate (WSP716, WSP716-S, WSP724, WSP724-S)

(MetalStud not evaluated byUL)

WALLCONSTRUCTION ADDITIONAL HARDWARE REQUIRED

Wood Stud, Wood Beam none

Concrete none

Metal stud WSP716, WSP716-S, WSP724, or WSP724-S

Other or unsure? Contact Customer Care

IMPORTANT! Certain types of walls require additional mounting hardware...

3 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

PLAV70-UNL PLAV70-UNL-S

PLAV70-UNLP PLAV70-UNLP-S

DESCRIPTION QTY. PART# PART#

Awallplate 1 201-1040 201-4040

Btilt-roll assembly 1 201-1042 201-4042

Carmassembly 1 201-1044 201-4044

Dwallsupportarmaxle 2 201-1041 201-1041

Evinyltrim 3 600-1012 600-1012

FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262

G.505 x .75 x .062" nylon washer 1 540-1074 540-1074

Htilt adjustment knob 1 560-0108 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315

J1.525 x 2 x .062" delrin washer 4 540-1070 540-1070

K#8-32 x .375" socket head cap screw 2 520-1210 520-1210

Lplastic finishing cap 6 590-1123 590-1123

Mholdingpin 2 580-1166 580-1166

Nretainerplug 2 590-1007 590-1007

O5/16 x 3" wood screw 8 520-1243 520-1243

P.250 x 1 x .068" washer 8 540-1063 540-1063

Q9/64"allenwrench 1 560-9728 560-9728

Rcablemanagementclips 8 590-1166 590-1166

Scable tie 8 590-1168 590-1168

T36"polyestermeshsleeve 2 600-1015 600-1015

U6 mm allen wrench 1 560-9716 560-9716

Wanchor 8 590-1025 590-1025

Before you start make sure all parts

listed are included with your product.

Wall Mount Parts List

Some parts may appear slightly different than illustrated.

R S

4 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

PLAV 70-UNL PLAV 70-UNL-S PLAV 70-UNLP PLAV 70-UNLP-S

Description Qty Part # Part # Part # Part #

AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110

BB shallow adapter bracket 2 200-0756 200-0757 200-0754 200-0755

CC deep adapter bracket 2 200-0752 200-0753 200-0750 200-0751

DD allen wrench 1 560-9646 560-9646 560-0072 560-0072

Before you begin, make sure all parts shown are included with your product.

Adapter Bracket Parts List

5 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

M5 x 25 mm (4)

520-1122

M4 x 12 mm (6)

510-1079

M4 x 25 mm (4)

510-1082

M5 x 12 mm (4)

520-1064 M6 x 12 mm (4)

520-1050

M6 x 25 mm (4)

520-1211

I.D. 5.6 mm (4)

540-1057

multi-washer(6)

580-1036

I.D. 8.7 mm (4)

540-1059

SecurityAdapter Bracket Fasteners

M6 x 20 mm (4)

520-9554

M6 x 30 mm (4)

520-1067

M8 x 15 mm (6)

520-1068

M8 x 40 mm (4)

520-1152

M8 x 25 mm (4)

520-1101

M6 x 20 mm (4)

520-9402

M6 x 30 mm (4)

510-9109 multi-washer(6)

580-1036

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

M4 x 12 mm (6)

504-9013

Phillips Adapter Bracket Fasteners

M4 x 25 mm (4)

504-1015

M5 x 12 mm (4)

520-1027 M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208

I.D. 5.6 mm (4)

540-1057

M8 x 25 mm (4)

520-1031

I.D. 8.7 mm (4)

540-1059

6 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

• Installermust verify that the supporting surfacewillsafely support the combined load oftheequipment and all attached

hardwareandcomponents.

• Tightenwoodscrews so that wall plate isfirmlyattached, but do not overtighten. Overtightening candamagethe

screws,greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovidedisfor attachment of mount through standard thickness drywallorplasterintowood studs. Installers

areresponsibletoprovidehardwareforothertypesofmountingsituations.

• Neverexceed the Maximum UL Load Capacityof200 lb (91 kg).

WARNING

Installation to Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useof an edge-to-edge studfinder is highly recommended. Based on their edges, draw a verticalline down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .43" below the

desired screen center. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level, secure it

using eight 5/16x 3" wood screws (O) and washers (P).

Skip to step 2 on page 8.

• Never mount this product to metal studs without the

requiredaccessory.

WARNING

7 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

IMPORTANT!Concretemustbe2000 psidensity

minimum.

Use wall plate (A), making sure that it is level, as a

template to mark holes. The top mounting slots

should be located .43" below the desired screen

center. Use the masonry bit to drill 5/16" (8 mm) dia.

holes to a minimum depth of 3" (76 mm). Insert

anchors (W) in holes flush with wall as shown (right).

Placewallplate(A)overanchors(W)andsecurewith

5/16 x 3" wood screws (O) and washers (P).

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

• Neverexceed the Maximum UL Load Capacityof200 lb (91 kg).

WARNING

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattachconcreteexpansionanchorstoconcrete

coveredwithplaster, drywall,orotherfinishingmate-

rial.Ifmounting to concrete surfaces covered with a

finishingsurfaceisunavoidable,thefinishingsurface

mustbecounterboredas shown below. Ifplaster/

drywall is thicker than 5/8", custom fasteners must be

suppliedbyinstaller(NotULevaluated).

WARNING

• Tighten wood screws so that wall plate is firmly

attached,butdonotovertighten.Overtighteningcan

damagescrews,greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

Installation to Concrete Wall

concrete

surface

Drill hole(s) and insert anchor(s) (W)

mounting

plate

Place plate over anchor(s) (W) and secure with screw(s)(O)

Tighten all fasteners

INCORRECT CORRECT

CUTAWAYVIEW

mounting

plate

plaster/

drywall

concrete mounting

plate concrete

plaster/

drywall

8 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

• If you are uncertain that product is properly installed, call customer care.

WARNING

To route cables through cord management

channels:Slideonemeshsleeve(T)over

each cable. Use cable ties (S) to tighten mesh

sleevesto cables.

Pullcords through cord managementchan-

nels,leaving enough slack toallow full range of

movementfor swing arm assembly (C)as

showniffigure 3.1.

3-1

fig 3.1

To route cables using cable management clips:

Snapeight cable management clips(R)intoboth

swing arms(C)as shown in figure 3.2.Cable ties (S)

areusedwith clips for cord management.

Slideone mesh sleeve (T) overeach cable. Use

cable ties (S) to tighten mesh sleeves to cables.

CORD

MANAGEMENT

CHANNEL C

3-1

Note: There are three mounting positions. The

center position is shown right. Arm assemblies

must be mounted with one mounting hole

separating them. Slidewashers(J)over wall

support arm axles (D). Next, insert plastic caps (N)

into axles. Then, insert holding pins (M) into axles.

See detail 1.

Note: Fit of axles (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

Insert socket cap screws (K) into hole at bottom of

wall support arm axles (D) as shown in detail 3.

Tightenscrewusing9/64"allen wrench (Q).

Place arm assembly (C) with washers (J) into wall

plate (A). Insert axle assemblies shown in detail 1

throughwallplate (A), arm assembly (C), and

washers (J). Lock axles in place by aligning

holding pins (M) with notches shown in detail 2.

2-1

2-2

DETAIL 3

NOTCH

DETAIL 2

DETAIL 1

fig 3.2

9 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).Attach tilt-roll assembly to adapter bracket (AA)

with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

• Donotovertightenscrews! Overtightening mayhinder

rolloption.

CAUTION

4Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm

assembly(C).

4-1 Insertone finishing cap (L) intoeach unused hole of wallplate (A).

SWIVELBOX

10 of 13 ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.

.25" F

• Use an assistant or mechanical lifting equipment to safely lift and position the plasmaTV.

WARNING

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

SWIVELBOX

Hook tilt-roll assembly (B) onto M10 screws (F).

Insert carriage bolt (I) into slot of swivel box as

shown in figure 6.1. Install nylon washer (G) and tilt

adjustmentknob(H).

Install remaining two M10 screws (F) as shown in

figure6.2.HANDTIGHTENallfourM10screwsto

allowfortiltadjustment.Removetapefromcarriage

bolt (I). For tilt adjustment, gently push back on the

top of plasma to relieve pressure on knob.Adjust tilt

to desired position and tighten tilt adjustment knob

(H), then securely tighten all four M10 screws (F)

using 6 mm allen wrench (U).

6-1

6-2

Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

SWIVELBOX fig 6.1 fig 6.2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de PEERLESS Mounts

PEERLESS Mounts

PEERLESS Mounts Paramount PF660 Guía

PEERLESS Mounts

PEERLESS Mounts SUT660P Guía

PEERLESS Mounts

PEERLESS Mounts Vector Pro II PJF2-UNV Series Guía

PEERLESS Mounts

PEERLESS Mounts Solid-Point PLA 2 Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B1C Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B4C Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3H Guía

PEERLESS Mounts

PEERLESS Mounts DS-VL-H060 Guía

PEERLESS Mounts

PEERLESS Mounts PLAV70-UNLP-GB Guía

PEERLESS Mounts

PEERLESS Mounts SmartMount SA740P Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B6C Guía

PEERLESS Mounts

PEERLESS Mounts DS-VL-H072 Guía

PEERLESS Mounts

PEERLESS Mounts ACC328 Guía

PEERLESS Mounts

PEERLESS Mounts SmartMount ST630P Guía

PEERLESS Mounts

PEERLESS Mounts FPEWM Guía

PEERLESS Mounts

PEERLESS Mounts ACC 310 Guía

PEERLESS Mounts

PEERLESS Mounts ACC488 Guía

PEERLESS Mounts

PEERLESS Mounts SmartMount ST632P Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3C Guía

PEERLESS Mounts

PEERLESS Mounts SmartMount SF630P Guía

PEERLESS Mounts

PEERLESS Mounts FPECMC-01 Guía

PEERLESS Mounts

PEERLESS Mounts LCT-A1B2H Guía

PEERLESS Mounts

PEERLESS Mounts DS-VL-H048 Guía

PEERLESS Mounts

PEERLESS Mounts RTLA-100 Guía

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario