Patton electronics 1206P Manual de usuario

MODEM ELIMINATOR, X.21

1206P

(CTS ME-X.21)

INSTALLATION AND OPERATIONS MANUAL

Doc #: 118001UA

Part #: 07M1206P-A

An ISO-9001

CertifiedCompany

1206P INSTALLATION AND OPERATIONS MANUAL

118001UA

PATTONELECTRONICSCO.

COPYRIGHTNOTICE

PROPRIETARY NOTICE

The information contained herein is proprietary and confidential to Patton Electronics

Co. Any reproduction or redistribution of this publication, in whole or in part, is

expressly prohibited unless written authorization is given by Patton Electronics Co.

WARRANTY NOTICE

WARRANTIES: Patton Electronics Co. (hereafter referred to as Patton) warrants

that its equipment is free from any defects in materials and workmanship. The

warranty period shall be two years from the date of shipment of equipment.

Patton’s sole obligation under its warranty is limited to the repair or replacement of

the defective equipment, provided it is returned to Patton, transportation prepaid,

within a reasonable period. This warranty will not extend to equipment subjected to

accident, misuse, alterations or repair not made by Patton or authorized by Patton

in writing.

PUBLICATION NOTICE

This manual has been compiled and checked for accuracy. The information in this

manual does not constitute a warranty of performance. Patton reserves the right to

revise this publication and make changes from time to time in the content thereof.

Patton assumes no liability for losses incurred as a result of out-of-date or incorrect

information contained in this manual.

INSTALLATION AND OPERATIONS MANUAL1206P

118001UA

PATTONELECTRONICSCO.

EMISSION REQUIREMENTS

FCC CLASS A

Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of FCC rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expence.

CANADIAN EMISSIONS

This digital apparatus does not exceed the Class A limits for noise emmissions from

a digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le present appareil numerique n’emet pas de bruits redioelectriques depassant les

limites applicables aux appareils numeriques de la Class A prescites dans le

Reglement sur le brouillage redioelectrique edicte par le ministere des

Communications du Canada.

1206P INSTALLATION AND OPERATIONS MANUAL

118001UA

PATTONELECTRONICSCO.

iii

TABLE OF CONTENTS

CHAPTER 1 - OPERATION

Clocking ........................................................................................................................... 1-1

DelayingINDICATE .......................................................................................................... 1-1

Power .............................................................................................................................. 1-1

Approvals......................................................................................................................... 1-2

Available Options............................................................................................................. 1-2

CHAPTER 2 - SETUP AND INSTALLATION

Power Connection .......................................................................................................... 2-1

Factory Configuration Switch Settings.......................................................................... 2-1

Disassembly .................................................................................................................... 2-2

Installation ....................................................................................................................... 2-2

Equipment Grounding (JP4)........................................................................................... 2-2

IND Delay, Port 1 (SW2-1,2)........................................................................................ 2-2

IND Delay, Port 2 (SW2-4,5)........................................................................................ 2-2

Internal Baud Rate Selection (SW1-1,2,3,4) .............................................................. 2-3

High Speed Option Rates (JP7,JP8,JP9,JP10).......................................................... 2-3

Factory Test Jumpers (JP1).......................................................................................... 2-4

APPENDIX

DB-15 Connector Pins Used ......................................................................................... A-1

Signal Flow Diagram....................................................................................................... A-1

Strapping Guide .............................................................................................................. A-2

1206P INSTALLATION AND OPERATIONS MANUAL

118001UA

PATTONELECTRONICSCO.

1-1 OPERATION

CHAPTER 1 - OPERATION

The 1206P (CTS ME-X.21) is a cost effective solution for interconnection of X.21

terminal devices located in proximity of each other. The use of two modems is

eliminated with a resulting cost savings to the user. The 1206P (CTS ME-X.21)

complies with the CCITT V.11 balanced interface specification. Two 15 pin DB-15

connectors are provided to interface to the X.21 terminals.

Clocking

Clockingatratesupto768Kbpswiththelowspeedversionandupto2.048MbpswithHigh

SpeedOptionare providedbytheinternalbaudrategenerator. Thegeneratorwillprovide

clocksforbothterminalandinsurethedataissynchronizedwiththeSClockinboth

directions.

Delaying INDICATE

Control(C)isloopedback toIndicate(I)oneach Port. ToallowterminalsrequiringI delayto

functionproperly,selectable delaysofConstant,0mS,8mS and50mSofCto Idelayis

provided. EachPortisindividuallyconfiguredforIdelay.

Power

110or220 Volt operation is provided by aconvenientswitchlocated on the rear panel of the

1206P (CTS ME-X.21). Simply install the proper fuses (110VAC - .16ASB, 250V or 220VAC

-.8ASB,250V)andpowerplugforthecountry ofuse andselect theproper linevoltage and

theunitisreadyforoperation.

INTERNATIONAL

SERIES

1206P

PWR TRC I S

INSTALLATION AND OPERATIONS MANUAL1206P

118001UA

PATTONELECTRONICSCO.

1-2

OPERATION

Approvals

Safetyapprovals forUL,CSA & TÜVhave beengrantedallowing theModemEliminator to be

usedvirtuallyanywhereintheworld. FCCPart15classAemissionsapprovalsinsurethe

ModemEliminatorwillnotinterferewithanyoftheotherequipmentinyourdatacenter.

CENOTICE: The CE symbolonyour Patton Electronicsequipmentindicates that it isin

compliancewiththe Electromagnetic Compatibility (EMC)directiveand the Low Voltage

Directive (LVD) of the Union European (EU). A Certificate of Compliance is available by

contactingTechnical Support.

AvailableOptions

1206P(CTSME-X.21)isavailableinbothstand-alonesubsetorrack-mountableversions

(1206PRC). Variousconfigurationoftheinterfacearealsoavailablefromthefactory. The

1206PRC fits into the Model 1010R16 16 Card Rack Assembly.

1206P INSTALLATION AND OPERATIONS MANUAL

118001UA

PATTONELECTRONICSCO.

2-1 SETUP & INSTALLATION

Caution, Disconnect the POWER Before Removing The Cover

Vorsicht, Befor Deckung Abnehmen Mach Strom Zu.

Power Connection

Before connecting the 1206P (CTS ME-X.21) to a AC power source the top cover must be

installedand secured with thesupplied#8-32 screws. The unitissupplied with a110/220VA

voltageswitch,turntheswitchwithacoinorscrewdrivertotheappropriatevoltageforyour

country. EXAMPLE:IntheUnitedStatesof

America; set to 110VA. The unit is supplied

withaIECpowerconnectornexttothe

voltageselectswitch,plugthepowercord

intotheconnectoruntilitisfirmlyseated.

Youmaynowconnectthepowercordinto

yourACoutlet.

Factory Configuration Switch Settings

The1206P (CTSME-X.21)is configuredpriorto shipmentwiththe switchessetto the

followingdefaultpositions:

Switch 1 - 2, 3, 5 and 6 to OFF, 1 and 4 to ON.

Baud Rate = 64Kbps

Switch 2 - 1, 3, 4 and 6 to OFF, 2, and 5 to ON.

Port 1 IND Delay = 0

Port 2 IND Delay = 0

JP1 - JP3 always connected

JP4 - Open

HS Option

JP7 - Open

JP8 - Open

JP9 - Open

JP10 - Open

If the system application requires one of more of the default settings to be

changed, it will be necessary to remove the top cover of the enclosure to access

and change the DIP switches or Jumpers located on the printed circuit board.

CHAPTER 2 - SETUP AND INSTALLATION

CAUTION

: FOR CONTINUED PROTECTION AGAINST RISK

FIRE, REPLACE ONLY

WITH SAME TYPE

AND RATING FUSE.

110 / 220VA Switch

Fuse Drawer

PORT 1

IEC PowerConnector

110

220

100-120V

0.16ASB,250V

TO.16A,250V

200-240V

0.08ASB,250V

TO 0.08A,250V

* Switch fuse for 100-120V (.16ASB, 250V) or 200-240V

(.8ASB, 250V) as noted on rear of unit.

INSTALLATION AND OPERATIONS MANUAL1206P

118001UA

PATTONELECTRONICSCO.

SETUP & INSTALLATION 2-2

Disassembly

Removethetopcoverbyunscrewingthephillipsheadscrewslocatedontheleftandright

sidesof the 1206P (CTSME-X.21). Theconfiguration switches andJumpersare located on

thePCB as indicatedonthe strapping guideinthe Appendix ofthismanual. After the switch

selectionactivityiscompleted,

re-install the top cover BEFORE connecting to an AC

powersource.

Installation

Selectanappropriatelocation accessible to and within six feet ofanACpoweroutlet. The

outletmusthaveagroundpinreceptacleforproductwarranty.

"StraightThrough"

shielded

cables,terminatedinmale X.21(DB-15)connectorsshouldbeusedtoconnectthetwo

terminalsto the1206P (CTSME-X.21). Set theswitchesandJumpersto matchthe required

configurationusingthedescriptionsinthischapterandthestrappingguideintheappendix.

Equipment Grounding (JP4)

JP4providesforgroundinginterconnectioninthosesystemsrequiringaconnectionbetween

(FrameGround)and(SignalGround). ConnectONLYifrequired.

IND Delay, Port 1 (SW2-1,2)

SW2 position 1 and 2 selects C to I delay for the terminal connected to PORT 1. C (pins 3,10)

fromPORT1isloopedbacktoI(pins5,12)throughthedelaycircuitry.

SW2-1 SW2-2 DELAY

ON ON Const

OFF ON 0mS

ON OFF 8mS

OFF OFF 50mS

IND Delay, Port 2 (SW2-4,5)

SW2 position 4 and 5 selects C to I delay for the terminal connected to PORT 2. C (pins 3,10)

fromPORT2isloopedbacktoI(pins5,12)throughthedelaycircuitry.

SW2-4 SW2-5 DELAY

ON ON Const

OFF ON 0mS

ON OFF 8mS

OFF OFF 50mS

Internal Baud Rate Selection (SW1-1,2,3,4)

1206P INSTALLATION AND OPERATIONS MANUAL

118001UA

PATTONELECTRONICSCO.

2-3 SETUP & INSTALLATION

Selectionofinternal rates is provided byconfigurationof SW1 positions 1 through4and JP7

throughJP10iftheHighSpeedOptionhasbeeninstalledbythefactory. Thefollowingtable

showstheratesavailable:

SW1-1 SW1-2 SW1-3 SW1-4 RATE

ON ON ON ON HS Opt

OFF ON ON ON 768K

ON OFF ON ON 384K

OFF OFF ON ON 192K

ON ON OFF ON 128K

OFF ON OFF ON 72K

ON OFF OFF ON 64K*

OFF OFF OFF ON 57.6K

ON ON ON OFF 56K

OFF ON ON OFF 48K

ON OFF ON OFF 38.4K

OFF OFF ON OFF 28.8K

ON ON OFF OFF 19.2K

OFF ON OFF OFF 14.4K

ON OFF OFF OFF 9.6K

OFF OFF OFF OFF 4.8K

High Speed Option Rates (JP7,JP8,JP9,JP10)

IfthehighspeedoptionisinstalledthefollowingratescanbeutilizedbysettingSW1positions

1through 4to ON:

JP10 Installed JP7, JP8 & JP9 Removed - 256K

JP9 Installed JP7, JP8 & JP10 Removed - 512K

JP8 Installed JP7, JP9 & JP10 Removed - 1.024M

JP7 Installed JP8, JP9 & JP10 Removed - 2.048M

Factory Test Jumper (JP1)

INSTALLATION AND OPERATIONS MANUAL1206P

118001UA

PATTONELECTRONICSCO.

SETUP & INSTALLATION 2-4

ThefactorytestjumpermustbeinstalledfortheModemeliminatortoproperlyfunction. Insure

thisjumperisinstalledpriortooperationoftheunit.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Patton electronics

Patton electronics

Patton electronics 1082/F Manual de usuario

Patton electronics

Patton electronics 1140 Manual de usuario

Patton electronics

Patton electronics IM2RC/F-128K Manual de usuario

Patton electronics

Patton electronics 1088/I Manual de usuario

Patton electronics

Patton electronics 1226 Manual de usuario

Patton electronics

Patton electronics 1110 Manual de usuario

Patton electronics

Patton electronics 1058DVs Manual de usuario

Patton electronics

Patton electronics 3012/V24, 3014/V24, 3018/V24 Manual de usuario

Patton electronics

Patton electronics 1089/I Manual de usuario

Patton electronics

Patton electronics 1006 Manual de usuario

Patton electronics

Patton electronics 1015 Manual de usuario

Patton electronics

Patton electronics 1004 Manual de usuario

Patton electronics

Patton electronics MODEL 1075 Manual de usuario

Patton electronics

Patton electronics 1088/K Manual de usuario

Patton electronics

Patton electronics NetLink 1082/I Manual de usuario

Patton electronics

Patton electronics 1045 Manual de usuario

Patton electronics

Patton electronics 1205P Manual de usuario

Patton electronics

Patton electronics 1202 Manual de usuario

Patton electronics

Patton electronics 1180/35 Manual de usuario

Patton electronics

Patton electronics 1092 Manual de usuario

Patton electronics

Patton electronics 1140RC Manual de usuario

Patton electronics

Patton electronics 1000 Manual de usuario

Patton electronics

Patton electronics 1012B Manual de usuario

Patton electronics

Patton electronics 1110A Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario