Paradyne KeepInTouch 3760 Manual de usuario

You have accessed an older version

of a Paradyne product document.

Paradyne is no longer a subsidiary

of AT&T. Any reference to

AT&T Paradyne is amended to

read Paradyne Corporation.

3760-A2-GB92-00

Issue 1

November 1994

KeepInTouch

Card Modem

Model 3760-B2

User’s Guide

Printed on recycled paper

dyn

Important Regulatory Information

AIssue 1 November 1994

  

1994 AT&T Paradyne Corporation*

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of

this publication may be copied or distributed, transcribed, stored

in a retrieval system, or translated into any human or computer

language in any form or by any means, electronic, mechanical,

magnetic, manual or otherwise, or disclosed to third parties

without the express written permission of AT&T Paradyne

Corporation, 8545 126th Ave. N., P.O. Box 2826, Largo, Florida

34649-2826.

AT&T Paradyne Corporation makes no representation or

warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for

a particular purpose. Further, AT&T Paradyne Corporation

reserves the right to revise this publication and to make changes

from time to time in the contents hereof without obligation of

AT&T Paradyne Corporation to notify any person of such

revision or changes.

Changes and enhancements to the product and to the

information herein will be documented and issued as a new

release to this manual.

A Reader’s Comments form is provided at the front of this

publication and your comments are appreciated. If the form has

been removed, address comments to AT&T Paradyne

Corporation, Technical Publications, 8545 126th Ave. N., P.O.

Box 2826, Largo, Florida 34649-2826. AT&T Paradyne may use

or distribute any of the information supplied, as appropriate,

without incurring any obligation whatsoever.

*AT&T Paradyne is a member of AT&T’s Multimedia Products

and Services Group.

Important Regulatory Information

Issue 1 November 1994

Trademarks

Bell is a registered trademark of the Regional Bell Operating

Company.

KeepInTouch is a trademark of AT&T.

MNP is a registered trademark of Microcom, Inc.

PKUNZIP is a registered trademark of PKWARE, Inc.

All other product names are copyrighted and registered trademarks

of their respective owners.

Warranty

A limited warranty is provided with this product. Refer to the

enclosed Warranty Card for more information.

Important Safety Instructions

1. Read and follow all warning notices and instructions

marked on the product or included in the manual.

2. Do not attempt to service this product yourself, as opening

or removing covers may expose you to dangerous high

voltage points or other risks. Refer all servicing to qualified

service personnel.

3. General purpose cables are provided with this product.

Special cables, which may be required by the regulatory

inspection authority for the installation site, are the

responsibility of the customer.

4. When installed in the final configuration, the product must

comply with the applicable Safety Standards and

regulatory requirements of the country in which it is

installed. If necessary, consult with the appropriate

regulatory agencies and inspection authorities to ensure

compliance.

5. A rare phenomenon can create a voltage potential

between the earth grounds of two or more buildings. If

products installed in separate buildings are

interconnected, the voltage potential may cause a

hazardous condition. Consult a qualified electrical

consultant to determine whether or not this phenomenon

exists and, if necessary, implement corrective action prior

to interconnecting the products.

Important Regulatory Information

CIssue 1 November 1994

In addition, if the equipment is to be used with

telecommunications circuits, take the following precautions:

– Never install telephone wiring during a lightning storm.

– Never install telephone jacks in wet locations unless the

jack is specifically designed for wet locations.

– Never touch uninsulated telephone wires or terminals

unless the telephone line has been disconnected at the

network interface.

– Use caution when installing or modifying telephone lines.

– Avoid using a telephone (other than a cordless type)

during an electrical storm. There may be a remote risk

of electric shock from lightning.

– Do not use the telephone to report a gas leak in the

vicinity of the leak.

Government Requirements and Equipment Return

Certain governments require that instructions pertaining to

modem connection to the public switched telephone network be

included in the installation and operation manual. Specific

instructions are listed in the following sections.

United States

Notice To Users Of The Public Switched Telephone Network

1. This equipment complies with Part 68 of the FCC rules. On

the equipment is a label that contains, among other

information, the FCC registration number and ringer

equivalence number (REN) for this equipment. If requested,

this information must be provided to the telephone company.

2. The Universal Service Order Code (USOC) associated with

the services the equipment is to be connected is RJ11C.

3. The Ringer Equivalence Number (REN) is used to determine

the quantity of devices which may be connected to the

telephone line. Excessive RENs on the telephone line may

result in the devices not ringing in response to an incoming

call. In most, but not all areas, the sum of the RENs should

not exceed five (5.0). To be certain of the number of devices

that may be connected to the line, as determined by the total

RENs, contact the telephone company to determine the

maximum RENs for the calling area.

Important Regulatory Information

Issue 1 November 1994

4. If the modem causes harm to the telephone network, the

telephone company will notify you in advance that temporary

discontinuance of service may be required. But if advance

notice is not practical, the telephone company will notify the

customer as soon as possible. Also, you will be advised of

your right to file a complaint with the FCC if you believe it is

necessary.

5. The telephone company may make changes in its facilities,

equipment, operations, or procedures that could affect the

operation of the equipment. If this happens, the telephone

company will provide advance notice in order for you to

make the necessary modifications in order to maintain

uninterrupted service.

6. If your modem needs to be returned for repair or

replacement, follow the return policy as indicated on your

warranty card.

7. No repairs may be made by the end use customer.

8. This modem cannot be used on public coin service provided

by the telephone company. Connection to Party Line Service

is subject to state tariffs. (Contact the state public utility

commission, public service commission or corporation

commission for information.)

9. The Telephone Consumer Protection Act of 1991 makes it

unlawful for any person to use a computer or other

electronic device to send any message via a telephone fax

machine unless such message clearly contains in a margin

at the top or bottom of each transmitted page or on the first

page of the transmission, the date and time it is sent and an

identification of the business or other entity, or other

individual sending the message and the telephone number

of the sending machine of such business, or other entity, or

individual.

In order to program this information, follow the steps outlined

in the manual supplied with your fax software.

10. An FCC compliant telephone cord with modular plugs is

provided with this equipment. This equipment is designed to

be connected to the telephone network or premises wiring

using a compatible modular jack which is Part 68 compliant.

Important Regulatory Information

EIssue 1 November 1994

EMI Warnings

!WARNING:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and

used in accordance with the instruction, may cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on. The user is

encouraged to try to correct the interference by one or more

of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and

receiver

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician

for help

!WARNING:

The authority to operate this equipment is conditioned by the

requirement that no modifications will be made to the

equipment unless the changes or modifications are expressly

approved by AT&T Paradyne.

To Users of Digital Apparatus in Canada:

This digital apparatus does not exceed the Class B limits for

radio noise emissions from digital apparatus set out in the

radio interference regulations of the Canadian Department of

Communications.

Le presént appareil numérique n’émet pas de bruits

radioélectriques dépassant les limites applicables aux

appareils numériques de la Classe B prescrites dans le

règlement sur le brouillage radioélectrique édicté par Le

Ministère des Communications du Canada.

Important Regulatory Information

Issue 1 November 1994

Canada

Notice To The Users Of The Canadian

Public Switched Telephone Network

The Canadian Department of Communications label identifies

certified equipment. This certification means that the equipment

meets certain telecommunications network protective,

operational and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is

permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be

installed using an acceptable method of connection. In some

cases, the company’s inside wiring associated with a single line

individual service may be extended by means of a certified

connector assembly (telephone extension cord). The customer

should be aware that compliance with the above conditions may

not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized

Canadian maintenance facility designated by the supplier. Any

repairs or alterations made by the user to this equipment, or

equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical

ground connections of the power utility, telephone line and

internal metallic water pipe system, if present, are connected

together. This precaution may be particularly important in rural

areas.

!CAUTION:

Users should not attempt to make such connections

themselves, but should contact the appropriate electric

inspection authority, or electrician, as appropriate.

The Load Number for this equipment is listed on the modem’s

label. The Load Number (LN) assigned to each terminal device

denotes the percentage of the total load to be connected to a

telephone loop which is used by the device to prevent

overloading. The termination on a loop may consist of any

combination of devices subject only to the requirement that the

total of the Load Numbers of all devices does not exceed 100.

Important Regulatory Information

GIssue 1 November 1994

If your equipment is in need of repair, return it to its place of

purchase or arrange to have your equipment repaired by

contacting Inventory Control Office, 100 York Blvd., Suite 200,

Richmond Hill, Ontario L4B1J8, telephone (416) 494-0453.

Issue 1 November 1994

Contents

1Introduction

Welcome to the World of Portable, High-Speed

Data Communications! 1-1. . . . . . . . . . . . . . . . . . .

KeepInTouch Card Modem Package 1-2. . . . . . . . . . . .

Supplied Equipment 1-2. . . . . . . . . . . . . . . . . . . . . .

Additional Equipment You Will Need 1-3. . . . . . . .

Where to Find Additional Information 1-3. . . . . . . . . . . .

2Installation

KeepInTouch Card Modem Installation

Procedures 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fax Application Software 2-3. . . . . . . . . . . . . . . . . . . . . .

3Using Your Modem

What is a Modem? 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Modes (Command and Data) 3-2. . . . . . . . .

Using AT Commands 3-3. . . . . . . . . . . . . . . . . . . . . . . . . .

Making a Call with Your Modem 3-4. . . . . . . . . . . . . . . .

Dial Modifiers 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . .

Examples of Dial Command Strings 3-6. . . . . . . .

Disconnecting a Call 3-7. . . . . . . . . . . . . . . . . . . . . . . . . .

Manually Answering a Call 3-8. . . . . . . . . . . . . . . . . . . . .

Using the Escape Sequence — Switching Between

Data Mode and Online Command Mode 3-9. . . .

Viewing, Selecting, and Saving Modem Settings 3-9. .

View User Profile Command (&V) 3-10. . . . . . . . . .

Save (Write to Memory) Command (&W) 3-10. . . .

Reload Factory Settings Command (&F) 3-11. . . .

Reload Settings from a User Profile (&Y) 3-12. . . .

Reset Modem and Load User Profile (Z) 3-12. . . .

Otros manuales para KeepInTouch 3760

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Paradyne

Paradyne

Paradyne COMSPHERE 3921 Manual de operación y mantenimiento

Paradyne

Paradyne COMSPHERE 3810 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

Paradyne

Paradyne Hotwire 6210 Instrucciones de funcionamiento originales

Paradyne

Paradyne 3920 Guía de inicio rápido

Paradyne

Paradyne COMSPHERE 3610 Manual de instrucciones

Paradyne

Paradyne Hotwire 6205 Manual de usuario

Paradyne

Paradyne HotWire 5170 Manual de usuario

Paradyne

Paradyne COMSPHERE 3800 Series Manual de usuario

Paradyne

Paradyne COMSPHERE 3800 Series Manual del propietario

Paradyne

Paradyne 6310 Manual de usuario

Paradyne

Paradyne Hotwire 8775 Manual de usuario

Paradyne

Paradyne HotWire 7915 Manual de usuario

Paradyne

Paradyne COMSPHERE 3825Plus Manual de usuario

Paradyne

Paradyne COMSPHERE 3910 Manual de instrucciones

Paradyne

Paradyne Hotwire 7974 Manual de usuario

Paradyne

Paradyne COMSPHERE 3810 Manual del propietario

Paradyne

Paradyne COMSPHERE 3810Plus Manual de operación y mantenimiento

Paradyne

Paradyne Hotwire 7985 Manual de usuario

Paradyne

Paradyne COMSPHERE 3821PLUS Manual de usuario

Paradyne

Paradyne CopperJet 810 Manual de usuario

Paradyne

Paradyne COMSPHERE 3811Plus Manual de usuario

Paradyne

Paradyne FrameSaver FLEX 9123 Manual de usuario

Paradyne

Paradyne COMSPHERE 3920PLUS Series Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario

Zoom

Zoom 1070 Series Manual de usuario