Paradyne Hotwire ReachDSL 6350-A4 Manual de usuario

Hotwire®ReachDSL™Modem, Model 6350-A4

with Inline Phone Filter

Installation Instructions

Document Number 6350-A2-GN12-00

September 2001

Contents

Hotwire 6350 ReachDSL Modem Overview ................................................. 1

Getting Started .............................................................................................. 4

Installing the Hotwire 6350 ReachDSL Modem ............................................ 5

Power-On ...................................................................................................... 7

Troubleshooting ............................................................................................. 9

Increasing the Number of End-User Systems .............................................. 10

Cables & Connectors .................................................................................... 11

Optional ReachDSL Modem Wall Placement ............................................... 13

Technical Specifications for Hotwire 6350 ReachDSL Modem ..................... 15

Important Safety Instructions ........................................................................ 16

Warranty, Sales, Service, and Training Information ...................................... 22

Hotwire 6350 ReachDSL Modem Overview

The Hotwire®6350 ReachDSL™Modem is a component in the Hotwire ReachDSL

System and interoperates with the Hotwire 8312 or 8314 ReachDSL/MVL®Card in the

Hotwire GranDSLAM (Digital Subscriber Line Access Multiplexer) system. This system

provides high-speed Internet or corporate LAN access over traditional twisted-pair

copper telephone wiring.

The ReachDSL technology:



Operates over existing copper wire with existing telephone jacks.



Utilizes an inline phone filter on the modem’s PHONE jack.



Includes a second line pass-through from the ReachDSL modem’s LINE jack to

PHONE jack to accommodate an attached 2-line telephone.



Provides adaptive data rates to dynamically adapt and allocate bandwidth to

optimize applications.

Hotwire ReachDSL System

Copper pairs run from the central office (CO) to the customer premises (CP) to create

the local loop. The local loop terminates on the customer premises at the demarcation

point.

NOTES:

In this document:

—A telephone is used to represent any equipment that plugs into a phone jack

and uses the POTS line, such as a phone, modem, or fax machine.

—End-user system is used to represent any PC with an Ethernet connection and

ReachDSL-based service.

—RJ11 wall jack is used to represent either an RJ11 or an RJ14 wall jack. The

RJ14 wall jack is used for a phone with two lines.

—Service provider is used to represent any Internet Service Provider (ISP) or

remote LAN access provider.

00-16867

ReachDSL

Modem

Customer Premises (CP)

DSL/POTS

Ethernet

Crossover

Cable Ethernet

Cable

Central

Office

(CO) Local Loop

Hub

DSL –Digital Subscriber Lines

POTS –Plain Old Telephone Service

End-user

Systems

Network

Service

Provider

(NSP) Demarcation

Point

Phone Filter

Depending on the type of phone handset and the quality of the home or business wiring,

a phone filter is recommended to minimize background noise during a phone

conversation. An internal phone filter is included with the Hotwire 6350 ReachDSL

Modem. If additional telephones are used on the same phone line as the ReachDSL

modem, install one phone filter on each telephone.

There are two Hotwire phone filters:



Hotwire 6035 Universal Phone Filter is designed for use with a tabletop phone.



Hotwire 6040 Wall Jack Phone Filter is designed for use with a wall phone.

Product-Related Documents

To install a phone filter, refer to the appropriate document:

Contact your sales or service representative to order additional product documentation.

Paradyne documents are available on the World Wide Web at www.paradyne.com.

Select

Library

→

Technical Manuals

→

Hotwire DSL & MVL Systems.

Document

Number Document Title

6035-A2-GN11

Hotwire 6035 Universal Phone Filter Installation Instructions

6040-A2-GN11

Hotwire 6040 MVL Wall Jack Phone Filter Installation Instructions

PHONELINE

ETHERNET

POWER

01-16998

RJ11

Wall Jack

RJ11

Wall

Jack

Customer

Premises (CP)

ReachDSL

Modem

6035

Phone Filter 6040

Wall Jack

Phone

Filter

Getting Started

Before beginning your modem’s installation, make sure that you have all the equipment

that you need.

Package Checklist

Verify that your package contains the following:

❑Hotwire 6350 ReachDSL Modem

❑DSL interface cable with RJ11 connectors

❑Power cord with power transformer

Be sure to register your warranty at www.paradyne.com/warranty.

Wiring and Cables You Need

The following standard cables and connectors are used with this product:

❑Standard RJ11 (or RJ14) wall jack for the DSL cabling.

❑Standard Ethernet 8-pin, non-keyed modular plug for a PC or workstation with an

Ethernet straight-through or crossover cable.

—Refer to

Installing the Hotwire 6350 ReachDSL Modem

on page 5 for Ethernet

cable installation details.

—Refer to

Cables & Connectors

on page 11 for DSL and Ethernet cable pin

assignments.

Installing the Hotwire 6350 ReachDSL Modem

Place the Hotwire 6350 ReachDSL Modem on a flat surface with clearance for the rear

connectors.

Procedure

1. If a telephone is connected at the RJ11

wall jack where the modem will be installed,

unplug the telephone line from the wall jack.

2. Connect a telephone to the modem.

(Optional –go to Step 3 if you are not

connecting a telephone to the ReachDSL

modem.)

Plug the existing telephone interface cable

that was unplugged in Step 1 into the jack

labeled PHONE.

3. Use the supplied RJ11 6-pin interface cable for the ReachDSL LINE connection.

Insert one end of the cable into the jack labeled LINE. Insert the other end of the

cable into the RJ11 wall jack.

NOTE:

If you are installing a POTS splitter with another telephone, connect the

telephone to the jack labeled PHONE, then connect the jack labeled LINE to a

wall jack. Do NOT plug any cable into the POTS splitter jack labeled either

MODEM or DSL. In particular, make NO connections between a POTS splitter

and the modem.

01-17015a

RJ11

Wall Jack

01-17015

RJ11

Wall Jack

PHONE LINE

ETHERNET

POWER

RJ11

6-pin

Interface Cable

PHONE LINE

4. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable

into the jack labeled ETHERNET.

—Use a straight-through cable and connect the other end to an Ethernet hub.

(To connect to a hub’s Uplink connection, use an Ethernet crossover cable).

–or–

—Use an Ethernet crossover cable and connect the other end to a PC with an

Ethernet Network Interface Card (NIC) installed.

PHONE LINE

ETHERNET

POWER

01-17008

Ethernet

Line

Ethernet

Hub

87654321

Ethernet

Straight-Through

Cable

01-17009

Ethernet

Line

PC with Ethernet

Network Interface

Card

Ethernet

Crossover

Cable

PHONE LINE

ETHERNET

POWER

5. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the

transformer into an AC outlet.

The ReachDSL modem hardware installation is now complete. When the power cord is

installed, the ReachDSL modem goes through a power-on self-test.

Power-On

When power is applied, the ReachDSL modem performs self-diagnostics and the PWR

LED is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on

for one second.

PHONE LINE

ETHERNET

POWER

01-17010

Power

Jack

Transformer

ReachDSL

TST LINE ETHERNET

ALMPWR TX/RX

01-17003

Power –green

Alarm –red

Test –yellow

Transmit/Receive –green

Ethernet Link –green

DSL Line –green

Status LEDs

All of the LEDs turn on and off during the power-on self-test. After a successful self-test,

the LEDs should appear as indicated in BOLD in the Condition column below.

Refer to

Troubleshooting

on page 9 for LED indications requiring action.

LED Condition Status

PWR ON ReachDSL modem has power.

ALM OFF

No active alarms.

An alarm condition exists.

TST OFF

No active tests.

The TST LED is on during the power-on self-test and

during a test initiated by the service provider.

LINE ON

OFF

The DSL link is active and ready to transmit and receive

data.

The DSL link has not been established.

TX/RX ON

OFF

Data transmission is in progress on the DSL line.

The modem is not transmitting or receiving data.

ETHERNET ON

OFF

The Ethernet connection to the Ethernet hub or PC is

active.

No Ethernet 10BaseT device is detected.

Troubleshooting

LED Symptom Action

All LEDs are on. If LEDs remain on after ten minutes, the modem is not

functional. Contact the service provider.

ALM LED remains

on. The power-on self-test may have failed. Unplug the unit and

reapply power. If the alarm LED is still on, contact the service

provider.

ALM and TST LEDs

are blinking. Firmware download may be in progress. If firmware download is

not in progress or the LEDs continue blinking after ten minutes,

contact the service provider.

Ethernet LED is off. Verify that the Ethernet cable is securely installed at both ends,

and at least one PC is connected and powered on.

Verify that the correct straight-through or crossover cable is

installed. Refer to

Installing the Hotwire 6350 ReachDSL

Modem

on page 5.

LINE LED is off. Verify that the DSL LINE cable is securely installed on both

ends. If the problem continues, contact the service provider.

Verify that the line has dial tone. If there is no dial tone, contact

the service provider.

LINE LED is on and

there is no data

transmission.

The DSL link has been established but there is no data

transmission. Verify the Ethernet connection. If the problem

persists, contact the service provider.

LINE and Ethernet

LEDs are on and

there is no data

transmission.

The DSL and Ethernet links have been established but there is

no data transmission. If the problem continues, contact the

service provider.

PWR LED is off. Check that the power cord is securely installed on both ends.

If no LEDs are on, the power supply may be defective. Test the

outlet to verify power. If the problem persists, contact the

service provider.

If other LEDs are on, the PWR LED may be burned out. Unplug

the unit and reapply power; watch all LEDs during the power-on

self-test to verify if the PWR LED is functioning.

TST LED is on. A test initiated by the service provider may be active. Wait five

minutes. If the TST LED does not go off, contact the service

provider.

To improve data transmission throughput and minimize background noise during a

telephone conversation, make sure that:



The Hotwire 6350 ReachDSL Modem is always powered on, even when not in use,

and



A Hotwire phone filter is installed on every telephone on the same line as the

Hotwire 6350 ReachDSL Modem (see

Phone Filter

on page 3).

Increasing the Number of End-User Systems

A single end-user system is attached to the Hotwire 6350 ReachDSL Modem by using

an Ethernet crossover cable. To increase the number of end-user systems, connect all

the PCs to an Ethernet hub using a straight-through cable.

The Hotwire ReachDSL/MVL port card supports 32 hosts/subnets per DSL port and the

Hotwire ReachDSL Modem supports up to 256 MAC entries.

Otros manuales para Hotwire ReachDSL 6350-A4

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Paradyne

Paradyne

Paradyne COMSPHERE 3911 Manual de usuario

Paradyne

Paradyne COMSPHERE 3820Plus Manual de usuario

Paradyne

Paradyne CopperJet 810 Manual de usuario

Paradyne

Paradyne Hotwire 6310 MVL Manual de usuario

Paradyne

Paradyne COMSPHERE 3810 Manual

Paradyne

Paradyne HOTWIRE 7925 Manual de usuario

Paradyne

Paradyne 6218-A1-200 Manual de usuario

Paradyne

Paradyne COMSPHERE 3910 Manual de usuario

Paradyne

Paradyne COMSPHERE 6700 Series Manual de instrucciones

Paradyne

Paradyne HotWire 5170 Manual de usuario

Paradyne

Paradyne COMSPHERE 3910 Manual del propietario

Paradyne

Paradyne 3162 Manual de usuario

Paradyne

Paradyne COMSPHERE 3920PLUS Series Manual del producto

Paradyne

Paradyne 3980-A2-GZ40-20 Hoja de especificaciones

Paradyne

Paradyne BitStorm 6200 Manual de usuario

Paradyne

Paradyne KeepInTouch 3766 Manual de usuario

Paradyne

Paradyne 7984 Manual de usuario

Paradyne

Paradyne COMSPHERE 3920PLUS Series Manual de usuario

Paradyne

Paradyne COMSPHERE 3810Plus Manual de operación y mantenimiento

Paradyne

Paradyne Hotwire 7985 Manual de usuario

Paradyne

Paradyne Hotwire 6390 Manual de usuario

Paradyne

Paradyne COMSPHERE 3811 Manual de usuario

Paradyne

Paradyne FrameSaver FLEX 9123 Manual de usuario

Paradyne

Paradyne Hotwire 6205 Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario

Zoom

Zoom 1070 Series Manual de usuario