Paradox Digiplex DGP-620 Instrucciones de montaje
20-Zone & 48-Zone LED Keypads V1.3
Installer’s Guide
TABLE OF CONTENTS
INTRODUCTION ................................................3
Specifications ..............................................................3
INSTALLATION .................................................4
Connecting the Keypad ..............................................4
Connecting Keypad Zones .........................................4
Programmable Output (PGM) .....................................6
Finding an Unlabeled Keypad’s Serial Number ..........6
PROGRAMMING ...............................................7
Enter Module Programming Mode ..............................7
Programming Methods ...............................................8
Feature Select Programming .........................................8
Decimal Programming ...................................................9
Level Programming .......................................................9
WinLoad Programming ..................................................9
Module Broadcast .......................................................9
SYSTEM OPTIONS ..........................................11
Basic Overview .........................................................11
Partition Assignment .................................................12
Zone Display .............................................................12
Confidential Mode .....................................................13
Muting .......................................................................14
Beep on Exit Delay ...................................................14
Chime on Zone Closure ............................................14
Beep on Trouble .......................................................15
Keypad Tamper Enable ............................................16
Access Control .........................................................16
PGM PROGRAMMING ....................................17
PGM State ................................................................17
PGM Activation Event ...............................................17
PGM Deactivation Event ..........................................18
PGM Timed Mode ....................................................19
PGM Timer ...............................................................19
PGM Base Time .......................................................20
PGM Override ...........................................................20
Digiplex LED Keypads 3
1.0 INTRODUCTION
Thank you for choosing Paradox®Security Systems. The
Digiplex™ Security System is an advanced technology security
system that will provide reliable security protection and powerful
features that are easy to use.
The elegant Digiplex™ LED Keypads will allow easy access to
the security system’s functions. The illuminating LEDs provide
the system’s status at a glance.
Since all programming is accomplished through the keypad,
please read this manual carefully.
1.1 SPECIFICATIONS
Power input: 9-16 Vdc, 45mA typical
Operation Speed: 16 MHz
PGM current limit: 50 mA
Number of inputs: 1
Number of zones: 1 standard zone, no tamper recognition
Power indication: Yellow LED on
Locate indication: Greenand yellowLEDs flashsimultaneously
Network fault indication:Red and yellow LEDs flash alternately
Locate deactivation: Tamper switch
Weight: 200 g
Compatibility: Digiplex DGP-48 Control Panels
4 Installer’s Manual
2.0 INSTALLATION
2.1 CONNECTINGTHEKEYPAD
The Digiplex™ LED Keypads are connected to the control
panel's communication network in a star and/or daisy chain
configuration. The 4-wire communication network provides
power and two-way communication between the control panel
and all modules connected to it. Connect the four terminals
labeled red, black, green and yellow of each keypad to the
corresponding terminals on the control panel as shown in Figure
2.1. Refer to the Digiplex Control Panel's Reference &
Installation Manual for the maximum allowable installation
distance from the control panel.
2.2 CONNECTINGKEYPAD ZONES
Each keypad has one traditional hardwired input terminal,
allowing you to connect one detector or door contact directly to
the keypad. For example, a door contact located at the entry
point of an establishment can be wired directly to the input
terminal of the entry point keypad instead of wiring the door
contact all the way to the control panel.
Connect the device to the keypad's input terminal as shown in
Figure 2.1.
The keypad zone follows the control panel’s EOL
definition.
Digiplex LED Keypads 5
In order to communicate its status to the control panel, devices
connected to the keypad's input terminal must be assigned to a
zone in the control panel and the zone's parameters must be
defined.
The control panel does not recognize tampers
originating from the keypad zone.
For more information on zone assignment, please refer to the
Digiplex Control Panel's Reference & Installation Manual. Please
note that even with the ATZ (zone doubling) feature enabled, the
keypad supports only one detection device.
6 Installer’s Manual
2.3 PROGRAMMABLEOUTPUT(PGM)
Each keypad has one on-board PGM. A PGM is a programmable
output that toggles to its opposite state (i.e. a normally open PGM
will close) when a specific event has occurred in the system (see
section 5.2 of this manual). Upon activation, the PGM can provide
50mA to any device connected to it. If the current drawn is to
exceed the current limit, a relay should be connected to the PGM
as shown in Figure 2.1.
2.4 FINDINGAN UNLABELEDKEYPAD’SSERIALNUMBER
If the keypad’s serial number is missing, you can view the serial
number by entering 000 in Step 3 of Module Programming Mode
(see section 3.1 of this manual, page 7). The serial number will
illuminate one number at a time as you press the button
([10] LED represents zero).
Digiplex LED Keypads 7
3.0 PROGRAMMING
To program the Digiplex LED keypad you must enter “Module
Programming Mode”. Use the Digiplex LED Keypads Programming
Guide to keep track of which sections were programmed and how.
We strongly recommend you read this entire manual before you
begin programming.
3.1 ENTERMODULEPROGRAMMINGMODE
The keypad, like all other modules in the Digiplex system, is
programmed through the control panel. To do so, enter the
“Module Programming Mode”:
Step 1:
From Normal Mode press and hold the [0] key.
The keypad will emit a Confirmation Beep.
Step 2:
Enter the [INSTALLERCODE](by default 000000).
The [PRG]LED will flash.
Step 3:
Enter section [953].
The [PRG] LED and the [10] LED will illuminate ([10] represents
zero).
(To view an unlabeled keypad’s serial number, enter section [000]
instead of [953] and use the button to view the numbers one at
a time.)
8 Installer’s Manual
Step 4:Now in “Module Programming Mode”.
Enter the keypad’s 8-digit [SERIALNUMBER].
The keypad will emit a Confirmation Beep and the [PRG] LED will flash.
Step 5:
Enter the 3-digit [SECTION]you want to program.
The keypad will emit a Confirmation Beep. The [PRG]LED and
the numerical LEDs for any lt or previously programmed data will
illuminate.
Step 5:
Enter the required [DATA].
Depending on the section entered, the data required may differ.
The control panel will now redirect all programming to the
selected keypad. Every time the [CLEAR]button is pressed it will
revert to the preceding step, unless entering data, in which case
it will erase the current data entry. Please note that the serial
number is located on the keypad's PC board.
3.2 PROGRAMMINGMETHODS
3.2.1 Feature Select Programming
Program sections [001] to [005] by enabling or disabling options.
Within the sections, numbers from [1] to [8] represent a specific
keypad option (refer to the Digiplex LED Keypads Programming
Guide). Press the button corresponding to the desired option and the
digit’s LED will illuminate. This means the option is enabled. Press
the button again to extinguish the digit’s LED, thereby disabling the
option. Press the [ENTER]button when the options are set.
Otros manuales para Digiplex DGP-620
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Teclado de Paradox
Paradox
Paradox Spectra 1689 Manual de usuario
Paradox
Paradox 1686V Manual de usuario
Paradox
Paradox Esprit+ 642 Manual de usuario
Paradox
Paradox K32LCD+ Manual de usuario
Paradox
Paradox Digiplex EVO DGP2-641BL Manual de usuario
Paradox
Paradox K70C Manual de usuario
Paradox
Paradox Spectra 1689 Manual de usuario
Paradox
Paradox TM50 Touch Manual de usuario
Paradox
Paradox Paradox Digiplex DGP-610 Manual de usuario
Paradox
Paradox TM50 Touch Manual de usuario
Paradox
Paradox K32LCD+ Manual de usuario
Paradox
Paradox Spectra 1641 Manual de usuario
Paradox
Paradox MAGELLAN K10V/H Manual de usuario
Paradox
Paradox Digiplex DGP2-648 Manual de usuario
Paradox
Paradox Spectra 1641BL Manual de usuario
Paradox
Paradox Digiplex DGP2-648 Instrucciones de montaje
Paradox
Paradox Esprit+ 642 Instrucciones de montaje
Paradox
Paradox Paradox Esprit 616LED Manual de usuario
Paradox
Paradox Digiplex Manual de usuario
Paradox
Paradox TM50 Touch Manual de usuario
