ParaBody LP5 Manual de usuario
LP5 LEG PRESS 5
CLASSH
PART#7357701
REV.B
Version: LP5A-101
Revision: 11/08/02
1
ASSEMBLY INSTRUCTIONS
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
j
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
IMPORTANT SAFETY INFORMATION
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Parts List.........................4
NOTE: In a continual effort to improve our products, specifications are subject to change
2002 Life Fitness, a division of Brunswick Corporation. All rights reserved.
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
Assembly Instructions.....5-12
General Maintenance.......13
Warranty Statement.........14
Product Services.............15
Insert-Registration Card
©
Tools Required forAssembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
3
NOTE:BOLTLENGTH IS MEASUREDFROMTHEUNDERSIDEOFTHEHEADOFTHE BOLT.
BOLT LENGTH RULER:
BoltLengthRuler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody LP5 Leg Press. Please read these
instructions thoroughly and keep them for future reference.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
4
PARTS LIST
PART #
ACU04-1444
ACU04-1447
ACU04-1449
ACU04-1445
ACU04-1446
ACU04-1448
ACU02-1298
ACU07-0135
ACUDA1E03830016NB
KEY
1
2
3
4
5
6
7
8
9
QTY
1
1
1
1
1
1
1
2
6
PART #
ACUDC1250100020B
ACUDB2E03811000B
ACUDA1E02143413NB
ACUDB2E01212000B
ACU11-0080
ACU05-0372
ACU06-0437
ACUDACM04006007YB
DESCRIPTION
3/8”FLATWASHER
3/8”LOCKNUT
1/2X4-3/4” BOLT
1/2”LOCKNUT
SPRINGPINKNOB
3/4X 4” SHAFT
BUMPER,1-1/2X2
SETSCREW,M4X0.7X6L
QTY
8
2
4
4
1
4
2
1
DESCRIPTION
FRAME
SEATADJUST
HANDLE
MAINARM
SECONDARM
FOOTPLATE
PULLEYBRACKET
PAD
3/8X3”BOLT
KEY
10
11
12
13
14
15
16
17
NOTE:Someofthecomponentmaybepre-assembled.
9−1/2"
5
FIGURE 1
STEP 1:
• SECURELY assemble the SECONDARM (5) totheFRAME(1) using one 1/2 X 4-3/4” BOLT(12), one 3/4 X 4” SHAFT(15)
andone1/2” LOCK NUT (13). See FIGURE 1.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
12 1/2X 4-3/4”
1
13
15
4
5
• SECURELYassemble theMAINARM (4) tothe FRAME (1)using one 1/2X 4-3/4” BOLT(12),two3/4” FLANGEBEARINGS(14), one
3/4X 4” SHAFT(15)and one 1/2” LOCK NUT(13).SeeFIGURE 1. (NOTE:MakesureMAINARM isorientatedcorrectly,tophole
shouldbe9-1/2”fromthetopofarmasshowninFIGURE1.)
• NOTE:FollowSTEP1fortheassemblyoftheLEGPRESStotheGS1,GS2,GS4andGS8GymSystems.IfyouhavetheCM3orGS6
GymSystemproceedtoSTEP2.
• Proceed to to STEP 3.
• SECURELYassemble two1-1/2 X 2“ BUMPERS (16)to each sideofthe MAINARM(4)where theMAINARM(4) contacts theFRAME
(1)SeeFIGURE1.
16
Forassemblyto the GS1, GS2, GS4, GS8 Gym Systems .
Make sure MAINARM
is orientated correctly
• NOTE: FLANGEBEARINGSSHOULDBEPRE-INSTALLED
11−1/4"
6
FIGURE 2
STEP 2:
• SECURELY assemble the SECONDARM (5) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT(15) and one
1/2”LOCKNUT(13).SeeFIGURE2.
• SECURELY assemble the MAINARM (4) to the FRAME (1) using one 1/2 X 4-3/4” BOLT(12), one 3/4 X 4” SHAFT (15) and one 1/2”
LOCKNUT(13).SeeFIGURE2.(NOTE:MakesureMAINARMisorientatedcorrectly,topholeshouldbe11-1/4”fromthetopofarm
asshowninFIGURE2.)
• NOTE:FollowSTEP2fortheassemblyoftheLEGPRESStotheCM3andGS6GymSystem.IfyouhavetheGS1,GS2,GS4orGS8
GymSystemsproceedtoSTEP3.
• Proceed to to STEP 3.
• SECURELYassemble two 1-1/2X2 BUMPERS (16) to eachside of the MAINARM(4) wherethe MAINARM(4) contactsthe FRAME
(1)SeeFIGURE2.
12 1/2X 4-3/4”
1
13
15
4
5
16
Forassemblytothe CM3andGS6 GymSystem.
Make sure MAINARM
is orientated correctly
• NOTE: FLANGEBEARINGSSHOULDBEPRE-INSTALLED
FIGURE 3
STEP 3:
7
• Insert one 3/4 X 4” SHAFT(15)thru pre-installed FLANGE BEARINGS in the SECONDARM (5) as shown in FIGURE 3.
• Insert one3/4 X 4” SHAFT(15) thru pre-installed FLANGE BEARINGS in theMAINARM (4)as shown in FIGURE 3.
4
5
0123456
1/2 1/2 1/2 1/2 1/2 1/2
15
8
STEP4:
FIGURE 4
• SECURELYassembletheFOOTPLATE(6) tothe SECONDARM(5) and theMAINARM(4)using two 1/2X 4-3/4”BOLTS(12)and two
1/2”LOCKNUTS(13).SeeFIGURE4.
12 1/2 X 4-3/4”
6
5
13
4
9
STEP5:
FIGURE 5
3/8 X 3” 9
1
11
10
3
• SECURELY assemble the HANDLE (3) to the FRAME (1) using two 3/8 X 3” BOLTS (9), four 3/8” FLATWASHERS(10) and two 3/
8”LOCK NUTS(11)as showninFIGURE 5.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
10
STEP6:
FIGURE 6
• CAREFULLEYslide the SEATADJUST (2) into the FRAME (1) as shown.The SEAT can be adjusted by turning the SPRING PIN
KNOB (14) clockwise and pulling. The SEAT can be secured in place by releasing the pin into an adjustment hole and turning
clockwise until tight.
1
2
14
17
• Securely assemble one PLUNGER PIN(14)to the FRAME (1) as shown. (NOTE: ScrewPLUNGERPIN(14)in all the way)
• Securely assemble one M4 SET SCREW (17) to the plunger pin barrel on the FRAME (1) then back off 1/4 turn so PLUNGER PIN (14)
rotates freely until the threads come in contact with the M4 SET SCREW (17)
Tabla de contenidos
Otros manuales de Gimnasio en casa de ParaBody
ParaBody
ParaBody PBF064 Manual de usuario
ParaBody
ParaBody PBF849 Manual de usuario
ParaBody
ParaBody 440 Manual de usuario
ParaBody
ParaBody PBF405C Manual de usuario
ParaBody
ParaBody PBF506 Manual de usuario
ParaBody
ParaBody 950 st Manual de usuario
ParaBody
ParaBody 375101 Manual de usuario
ParaBody
ParaBody 950102 Manual de usuario
ParaBody
ParaBody Parabody 663 Manual de usuario
ParaBody
ParaBody 951 Manual de usuario
ParaBody
ParaBody cm3 Manual de usuario
ParaBody
ParaBody 40 Manual de usuario
ParaBody
ParaBody 216 Manual de usuario
ParaBody
ParaBody 807 BODYSYSTEM Manual de usuario
ParaBody
ParaBody 425104 Manual de usuario
ParaBody
ParaBody 465104 Manual de usuario
ParaBody
ParaBody PBF049A Manual de usuario
ParaBody
ParaBody 473 Manual de usuario
ParaBody
ParaBody 400102 Manual de usuario
ParaBody
ParaBody 917101 Manual de usuario
Manuales populares de Gimnasio en casa de otras marcas
Horizon Fitness
Horizon Fitness OXFORD 6 Manual de usuario
Energetics
Energetics Multi Trainer 5.1 Manual de usuario
Matrix
Matrix MG-PL Series Manual de usuario
Reebok
Reebok Tbr2i Manual de operación y mantenimiento
Weider
Weider 8300 Hard Drive Manual de usuario
Pure Fitness
Pure Fitness 8526HE Manual de usuario
