ParaBody GS2 Manual de usuario

GS2 GYM SYSTEM

CLASSH

PART # 7250101

REV.C Revision:11/01/02

USER’S GUIDE

WARNING:

Read and follow all directions

for each step to insure proper

assembly of this product.

Version: GS2-101

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF

EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!

1. Before using, read all the warnings and instructions

on the use of this machine. Use only for intended

exercise. DO NOT modify the machine.

2. Obtain a medical exam before beginning any

exercise program.

3. Keep body and clothing free of all moving objects.

4. Inspect the machine before use. DO NOT use it if it

appears damaged. DO NOT attempt to fix a broken or

ammed machine. Notify your authorized ParaBody

dealer before use and have repairs made by an

authorized service technician.

5. Be certain that weight pin is completely inserted.

Use only the pin provided by the manufacturer. If

unsure, call your authorized ParaBody dealer.

6. Never pin the weights or prop plate into an elevated

position. DO NOT use the machine if found in this

condition. DO NOT attempt to fix. Notify your

authorized ParaBody dealer.

7. Inspect cables and their connections before using

machine. Pay particular attention to the cable ends.

DO NOT attempt to fix. Notify your authorized

ParaBody dealer before use and have repairs made by

an authorized service technician.

8. Make sure all spring loaded pull pins are fully

engaged in the adjustment position and fully tighten

thumbscrew before use.

9. Children must not be allowed near this machine.

Supervise teenagers.

IMPORTANT SAFETY INFORMATION

TABLE OF CONTENTS

Safety Statement.............2

General Notes..................3

Tools Required................3

Gym Layout.....................4

NOTE: In a continual effort to improve our products, specifications are subject to change

ParaBody is a trademark of Brunswick Corporation

www.parabody.com

Parts list..........................5

Assembly Instructions.....6-21

General Maintenance.......22

Warranty Statement..........23

Product Services..............24

Insert-Registration Card

IMPORTANT NOTES

Please note:

Tools Required forAssembly

* Thank you for purchasing the ParaBody GS2 Gym System. Please read these

instructions thoroughly and keep them for future reference.

* Rubber mallet or hammer

* 3/4” wrench

* 9/16” wrench

* Ratchet with 3/4” and 9/16” sockets

* 5/32”Allen wrench

*Adjustable wrench

* Tape measure

NOTE:BOLTLENGTH IS MEASURED FROMTHEUNDERSIDEOFTHEHEADOFTHE BOLT.

BOLT LENGTH RULER:

* This product must be assembled on a flat, level surface to assure its proper function. DO NOT

securely tighten any frame connections until the entire frame has been assembled, unless

otherwise stated.

Bolt Length Ruler

0123456

1/2 1/2 1/2 1/2 1/2 1/2

BOLT LENGTH

Minimum Required Usable Space

Length = 82 inches (208.5 cm) 6’ 10”

Width = 71 inches (180.5 cm) 5’11”

Height = 83 inches (211 cm) 6’ 11”

1 Square = 1’ X 1’

Length = 82 inches (208.5 cm) 6’ 10”

Width = 108 inches (180.5 cm) 9’ 0”

9’

1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’

1’

7’

6’

5’

4’

3’

2’

Dimensions Including LP5 Leg Press (optional)

PARTS LIST

0123456

1/2 1/2 1/2 1/2 1/2 1/2

PART #

ACU04-1163

ACU04-1158

ACU02-1060

ACU04-1160

ACU04-1384

ACU04-1383

ACU04-1161

ACU04-1164

ACU04-1159

ACU04-1162

ACU04-1157

ACU02-1071

ACU07-0135

ACU01-1782

ACU6194601

ACU01-1783

ACU04-1099

ACU01-2009

ACU10-0204ASY

ACU13-0091-2

ACU13-0019-1

ACU7292501

ACU06-0024

ACU12-0041

ACU05-0193

ACUDA1E03813416NB

ACUDA1E03821216NB

ACUDA1E03830016NB

ACUDA1E03833416NB

ACUDA1E003883416NB

ACUDA1C01210413NB

ACUDA1E01283413NB

KEY

QTY

PART #

ACUDB2E03811000B

ACUDB2E01208000B

ACUDC1250100020B

ACUDC126013020B

ACU04-1171

ACU06-0363

ACU05-0322

ACU08-0074

ACU08-0073

ACU08-0011

ACU05-0320

ACU04-1165

ACU06-0047

ACU05-0323

ACU05-0212

ACU11-0059

ACU11-0068

ACU11-0060

ACU06-0194

ACU05-0017

ACU05-0036

ACU06-0357

ACU05-0311

ACUDI1080080U

ACU04-0622

ACUDB2E01212000B

ACU7308601

ACU04-1100

ACUDA1E03840016NB

ACU04-1344

ACU06-0364

ACU06-0416

DESCRIPTION

3/8” LOCK NUT

1/2” LOW HT LOCK NUT

3/8” FLAT WASHER

1/2” FLAT WASHER

3-1/2” CABLE GUARD

3/4” PLASTIC WASHER

3/4 X 4” SHAFT

3/8 X 3/4” FLANGE SPACER

3/8 X 1-1/16” FLANGE SPACER

3/8 X 1” LG SPACER

3/8 X 1-1/2” LG SPACER

WEIGHT STACK SPACER

WEIGHT STACK CUSHION

5/16 X 2” ROLL PIN

SHAFTCOLLAR

TAPER/LOCK SPRING PIN

T-HANDLE SPRING PIN

WEIGHT SELECTOR PIN

STAR KNOB 3/8”

ADJUSTABLE GLIDE

STARLOCK COLLAR

RH CAP

1/2” RHCAP HOLDER WASHER

SNAP LINK

LOW ROW BAR

1/2” LOCK NUT

WEIGHTSTACK LABEL

FOOTPLATE

3/8 X 4” BOLT

FRAME BRACE

PRESSARMSPACER

OVALENDCAP

QTY

DESCRIPTION

FRAME

BASE

BASEPLATE

BOOMPLATE LEFT

BOOMPLATERIGHT

PRESSHANDLERIGHT

PRESSHANDLELEFT

PRESSARM

PRIMARYPIVOT

SEATADJUST

LEGPEDESTAL

PULLEYPLATE

SEAT/BACKPAD

3/4X 17”TUBE

4X7”ROLLERPAD

72-3/8”GUIDEROD

LATBAR

3/4X 17/1/2” TUBE

HEADPLATEASSY

LATCABLE

LOWCABLE

WEIGHTPLATE

3-1/2”PULLEY

ANKLESTRAP

CHAIN

3/8X 1-3/4” BOLT

3/8X 2-1/2” BOLT

3/8X 3” BOLT

3/8X 3-3/4” BOLT

3/8X 8-3/4” BOLT

1/2X104mmBOLT

1/2X 8-3/4” BOLT

KEY

NOTE: SOMEOFTHEPARTSLISTEDMAYBEPRE-INSTALLED.

FIGURE 1

STEP 1:

3/8 X 3 29

• LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30)

and four 3/8” LOCK NUTS (34). See FIGURE 1.

3/8 X 4

• LOOSELY assemble the FOOTPLATE (62) to the lower holes in the FRAME (1) using one 3/8 x 3” BOLT (29) and one

3/8 LOCKNUT (34)

• LOOSELY assemble the TOP of FRAME BRACE (64) to the FRAME (1) using two 3/8 x 4” BOLT (63), two 3/8 WASHERS

(36) and two 3/8 LOCKNUTS (34) Assemble BOTTOM of FRAME BRACE (64) to FRAME (2) using one 3/8 x 3” BOLT

(29), one 3/8 x 2-1/2” BOLT (28) three 3/8 WASHERS (36) and one 3/8 LOCKNUT (34)

3/8 X 3

28 3/8 X 2-1/2

3/8 X 3-3/4

FIGURE 3

FIGURE 2

• CHECK THATTHE HEADPLATEANDWEIGHT PLATESAREASSEMBLEDAS SHOWN IN FIGURES 2 & 3

• Insert two GUIDE RODS (16) into the BASE (2) as

shown on FIGURE 4. (NOTE: If the GS2 SHROUD

OPTION was purchased, place the GUIDE RODS

(16) through the BOTTOM SHROUD BRACKET

(FOUNDINTHESHROUD KIT BOX) intotheBASE

(2), as shown in FIGURE 4.

• Using EXTREME CARE slide all fifteen

WEIGHT PLATES (22) down the GUIDE RODS (16)

onto the WEIGHTSTACK CUSHIONS (46). Make sure

that the keyholes of the WEIGHT PLATES (22) are all

facing the right way.

• Slide the head plate assembly down GUIDE RODS

(16) onto the weight stack.

• Slide one SHAFT COLLAR (48) down each

GUIDE ROD (16).

FIGURE 4

• Slide the following items in order down each GUIDE

ROD (16), one WEIGHT STACK SPACER (45), and

one WEIGHT STACK CUSHION (46)

STEP 5:

• Carefully slide the RIGHT (5) and LEFT (4) BOOM PLATES onto the GUIDE RODS (16 )as shown in FIGURE 5 and loosely

assembly BOOM PLATES (5), (4) to frame (1) using two 3/8 x 3-3/4” BOLTS (30) and two 3/8” LOCK NUT (34)

[CAUTION MUST BETAKEN NOT TO PULLGUIDE RODS (16) OUT OF BASE (2)]

• Screw ADJUSTABLE GLIDE (53) approximately 1/2” into FRAME (1) and tighten jam nut securely as shown

FIGURE 5

STEP 4:

3/8 X 3-3/4

HEAD

PLATE

ASSY

• (NOTE: Lubricate GUIDE RODS (16) with silicon

or teflon spray available at most hardware stores.)

GS2 SHROUD

BRACKET

OPTIONONLY

STEP 7:

• Using hammer tap one 5/16 X 2” ROLL PIN (47)

thru LEFT PRESS HANDLE (7) until it is flush

with other side of HANDLE as shown in

FIGURE 6

6 7

FIGURE 6

STEP 6:

• Place LEFT PRESS HANDLE (7) onto PRESS

ARM (8). Place PRESS ARM SPACER (65) as

shown over 5/6 x 2 ROLL PIN (47), make sure

that the 5/16 X 2” ROLL PIN (47) passes into

the slot located in the plate of the PRESS ARM

(8)

FIGURE 7

• Once in place secure and tighten the LEFT

PRESS HANDLE (7) to PRESS ARM (8)

using one 3/8” WASHER (36) and one

3/8” LOCK NUT (34)

0123456

1/2 1/2 1/2 1/2 1/2 1/2

NOTE:

Place PRESS ARM (8) upside down on floor as shown to complete this step.

HANDLES(7) MUSTBE PLACEDTOWARDS INSIDE OFPRESSARM

• Repeat STEP 6 for the RIGHT PRESS

ARM HANDLE (6)

• Repeat STEP 7 for the RIGHT PRESS

ARM HANDLE (6)

FLUSHSIDE

• IMPORTANT! Do not overtighten: PRESS

ARM should rotate freely

FIGURE 8

STEP 8:

• PlacePRESSARM (8) into PRIMARYPIVOT(9) and securely tighten using two 3/8 X 3”BOLTS (29), four 3/8” FLAT

WASHERS(36)two 3/8”LOCK NUTS(34)

• Insert and tighten two3/8”TAPER/LOCK SPRING PINS (49) into PRESSHANDLES(6),(7).

TIGHTEN

20lbs/ft

• LockPRESSARMS (6), (7)intoplace using 3/8”LOCKINGSPRING PINS (49)

Taper/Lock

Spring Pin

• Insert one OVAL END CAP(66) into openning of each arm as shown in FIGURE 8

3/8 X 3”

• TodisengageLOCKINGSPRINGPINS (49), pull out and twist 1/4 turn.

Otros manuales para GS2

Tabla de contenidos

Otros manuales de Gimnasio en casa de ParaBody

ParaBody

ParaBody 777 Manual de usuario

ParaBody

ParaBody PBF011 Manual de usuario

ParaBody

ParaBody Serious Steel 425104 Manual de usuario

ParaBody

ParaBody PBF203B Guía de inicio rápido

ParaBody

ParaBody LP5 Manual de usuario

ParaBody

ParaBody 843 Manual de usuario

ParaBody

ParaBody 425103 Manual de usuario

ParaBody

ParaBody PBF410A Manual de usuario

ParaBody

ParaBody 950 st Manual de usuario

ParaBody

ParaBody 807 BODY SYSTEM Manual de usuario

ParaBody

ParaBody 917101 Manual de usuario

ParaBody

ParaBody 359101 Manual de usuario

ParaBody

ParaBody 76 Manual de usuario

ParaBody

ParaBody 462 Manual de usuario

ParaBody

ParaBody 205101 Manual de usuario

ParaBody

ParaBody GS4 Manual de usuario

ParaBody

ParaBody PBF060 Manual de usuario

ParaBody

ParaBody 829 Manual de usuario

ParaBody

ParaBody 445104 Manual de usuario

ParaBody

ParaBody GS6 Manual de usuario

ParaBody

ParaBody 225 Manual de usuario

ParaBody

ParaBody Serious Steel 940101 Manual de usuario

ParaBody

ParaBody ex 350 Manual de usuario

ParaBody

ParaBody 415101 Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario

Insportline

Insportline RW600 Manual de usuario