Panduit CT-400 Manual de usuario

CT-400: PA24435A01_04 Page: 1 of 4 6-2018

CT-400

PA24435A01

Rev. 046-2018

NEW TOOLS – BEFORE PLACING INTO SERVICE

1. VISUALLY INSPECT TOOL

FOR DAMAGE.

All Panduit crimping tools are calibrated and inspected before they are shipped from

the factory. There is, however, a possibility of damage in shipment. All new tools

should therefore be inspected before being used.

2. CHECK DIE CLOSURE

3. CLEAN EXCESS OIL FROM

CRIMP DIES AND USE.

New tools are shipped factory lubricated. They do not require extensive cleaning.

After inspection, simply clean any excess oil from the crimping dies and place into

service.

CAUTION: Verify power is “OFF”

before working on wiring with this tool.

The plastic grips are for the user’s

comfort—and are not intended to

insulate against shock while working

on live electrical circuits.

WARNING: Controlled cycle device prevents tool from opening before cycle is

completed. Keep hands and other objects clear of pinch areas before closing.

ATTENTION: TO DISENGAGE CONTROLLED CYCLE DEVICE:

Turn the ratchet release screw counterclockwise and open handles.

The controlled cycle device will automatically reset after screw is released.

Email:

techsupport@panduit.com

EU Website:

www.panduit.com/emea

EU Email:

emeatoolservicecenter

@panduit.com

www.panduit.com

Technical Support:

1-800-777-3300

Panduit Europe • EMEA Headquarters

Tel: +31 (0) 546 580 452

Fax: +31 (0) 546 580 441

Ratchet Release

Screw

Notch

Lock Screw

BACK

VIEW

(FIG. 1)

FRONT

VIEW

(FIG. 2)

Adjustment

Locator Retention

Screws

Locator

CRIMP DIES for

Pan-Term

insulated terminals,

splices and wire joints.

CT-400: PA24435A01_04 Page: 2 of 4 6-2018

INSULATED TERMINAL INSTRUCTIONS

1. With handles in open position, insert terminal in

proper size die so that tongue slides into locator

slot. See product packaging for proper crimping

pockets.

2. Position terminal against locator and close handles

until barrel is held snugly in place -- do not deform

barrel.

Insert stripped wire into terminal until conductor

extends beyond barrel. See product packaging for

wire strip length.

Crimp by closing handles until controlled cycle

device releases. Handles will open automatically,

and crimped terminal may be removed.

FIG. 3

INSULATED SPLICE INSTRUCTIONS

1. Remove locator using a 2mm Allen wrench on the

locator retention screws [see FIG. 1]. (The 2.5mm

wrench may be used simultaneously to secure

screws on opposite side.)

With locator removed and handles opened, insert

splice in proper size die so that barrel extends 1/16"

beyond insulation closures.

3. Close handles until barrel is held snugly in position -

- do not deform barrel.

4. Insert stripped wire into splice and crimp by closing

handles until controlled cycle device releases.

Remove splice and repeat operation for crimping

other half of barrel.

FIG. 4

INSULATED WIRE JOINT INSTRUCTIONS

1. Remove locator using a 2mm Allen wrench on the

locator retention screws [see FIG. 1].

(The 2.5mm

wrench may be used simultaneously to secure

screws on opposite side.)

With terminal locator removed, insert wire joint in

proper size die so that ribs of molded insulator are

positioned against face of tool.

3. Twist ends of stripped wire together, trim and insert

into wire joint.

4. Crimp by closing handles until controlled cycle

device releases. Handles will open automatically,

and crimped joint may be removed.

FIG. 5

CT-400: PA24435A01_04 Page: 3 of 4 6-2018

IN-SERVICE TOOLS – AFTER TOOLS HAVE BEEN IN SERVICE

1. CLEAN AND VISUALLY

INSPECT FOR DAMAGE

ONCE A MONTH.

In-service tools should be cleaned and inspected at least ONCE A MONTH.

To clean---immerse in a commercial degreasing compound and wipe clean

with a lint free cloth. If a degreasing compound is not available, wipe with a

clean cloth.

2. CHECK DIE CLOSURE

After cleaning, inspect the crimping dies for proper die closure. See FIG. 6

for plug gaging instructions.

3. LUBRICATE TOOL ONCE A

WEEK.

4. CLEAN EXCESS OIL FROM

CRIMP DIES AND USE.

In-service tools should be lubricated ONCE A WEEK, and after every

cleaning. Lubricate all pins, pivots and bearing surfaces with a good grade

S.A.E. 20 or equivalent motor oil. Be sure to clean any excess oil from

crimping dies before using.

VISUAL INSPECTION

1. Visually inspect tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Remove the terminal locator and visually inspect the crimping dies for worn, chipped or broken surfaces.

Damaged crimping dies are objectionable and may go undetected when gaging the die closure.

3. If parts are missing, defective or damaged; contact your local Panduit Sales Office for information on repair

or replacement of tools; or contact Technical Support at 1-800-777-3300.

DIE CLOSURE INSPECTION: CT-400

Die Closure inspection is made by using the GO/NO-GO gaging dimensions listed in FIG. 6.

TO PERFORM DIE CLOSURE INSPECTION

1. Clean die and plug gage surfaces.

2. Close tool handles until crimping jaws are bottomed and handles are fully closed.

3. Using the proper gage member, insert the GO side into the die – it must pass completely through the

closure.

4. Reverse the gage and try to insert the NO-GO side into the die closure (Do Not use excessive force).

The NO-GO side may partially enter the die closure but must not pass completely through.

5. Perform the above procedure for both the crimp die closure and the insulation die closure, as listed in

FIG. 6.

CT-400: PA24435A01_04 Page: 4 of 4 6-2018

6. If both the GO and NO-GO conditions are met; the tool is dimensionally correct – if either condition fails,

adjust the DIE CLOSURE as follows:

1. Remove lock screw with small wrench [see FIG. 2].

2. With adjustment wrench provided, turn adjustment pin one notch – each notch produces approximately

.002” of adjustment. A clockwise turn increases the die closure and a counter-clockwise turn decreases

the die closure.

3. Close the tool and plug gage the die closure as instructed above. If the GO/NO-GO conditions are not

met, repeat Step (2) in one-notch increments until the tool is gages to be dimensionally correct.

Replace and tighten both lock screws after final adjustment.

7. If the above procedure fails to satisfy all GO and NO-GO conditions, contact your local Panduit Sales Office;

or contact Technical Support at 1-800-777-3300.

FIG. 6

POCKET

SIZE

CRIMP DIE CLOSURE

GAGING GAGE ELEMENT

DIAMETERS

GO NO-GO GO NO-GO

22-18 RED 0.096 0.106 0.0960 - 0.0963 0.1057 - 0.1060

16-14 BLUE 0.114 0.124 0.1140 - 0.1143 0.1237 - 0.1240

POCKET

SIZE

INSULATION DIE CLOSURE

GAGING GAGE ELEMENT

DIAMETERS

GO NO-GO GO NO-GO

22-18 RED 0.100 0.116 0.1000 - 0.1003 0.1157 - 0.1160

16-14 BLUE 0.142 0.158 0.1420- 0.1423 0.1577 - 0.1580

Otros manuales de Herramientas eléctricas de Panduit

Panduit

Panduit CT-1700 Manual de usuario

Panduit

Panduit GTH Manual de usuario

Panduit

Panduit PN433 Manual de usuario

Panduit

Panduit CT-2930/L Manual de usuario

Panduit

Panduit PBTMT Manual de usuario

Panduit

Panduit PTS Manual de usuario

Panduit

Panduit PDM Manual de usuario

Panduit

Panduit CT-1525 Manual de usuario

Panduit

Panduit GS4EH Manual de usuario

Panduit

Panduit CT-1090 Manual de instrucciones

Panduit

Panduit CT-1701 Manual de usuario

Panduit

Panduit BT2HT Manual de usuario

Panduit

Panduit ST2MT Manual de usuario

Panduit

Panduit BlackFin CT-2920 CCP Series Manual de usuario

Panduit

Panduit BlackFin CT-2980 Manual de usuario

Panduit

Panduit GS2B Manual de usuario

Panduit

Panduit GTH Manual de usuario

Panduit

Panduit CT-2940 Series Manual de usuario

Panduit

Panduit CA-800EZ Manual de usuario

Panduit

Panduit CT-2980/L Manual de usuario

Panduit

Panduit CT-260 Manual de usuario

Panduit

Panduit ST-100 Manual de usuario

Panduit

Panduit PA24849A01 Manual de usuario

Panduit

Panduit CP-991 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual