Panduit CTFP-40 Manual de usuario

CTFP-40

PA29443A01

Rev. 02 3-2019

BENCHMOUNT PNEUMATIC CRIMPING PRESS

OPERATING INSTRUCTIONS

Original Instructions

TO REDUCE THE RISK OF INJURY, USER

MUST READ INSTRUCTION MANUAL

NOTE: In the interest of higher quality and value, Panduit products are

continually being improved and updated. Consequently, pictures may vary

from the enclosed product.

For the most current version of this instruction manual, go to

www.panduit.com.

Email:

techsupport@panduit.com

EU Website:

www.panduit.com/emea

EU Email:

emeatoolservicecenter

@panduit.com

www.panduit.com

Panduit Corp.

USA Technical Support

Tel: 800-777-3300

Panduit Europe • EMEA Service Center

Tel: +31 546 580 452 • Fax: +31 546 580 441

ENGLISH

PA29443A01_02_ENG Page: 1 of 8 3-2019

Table of Contents

1. SAFETY.............................................................................................................................2

1.1 Basic information.............................................................................................................2

1.2 Symbols ..........................................................................................................................2

1.3 Dangerousness of the machine.......................................................................................2

1.4 Designated use ...............................................................................................................2

1.5 Sources of danger...........................................................................................................3

1.6 Work places.....................................................................................................................3

1.7 Safety devices.................................................................................................................3

1.8 Permitted operators.........................................................................................................3

1.9 Guarantee .......................................................................................................................3

2. DESCRIPTION...................................................................................................................4

2.1 Application.......................................................................................................................4

2.2 Components....................................................................................................................4

2.3 Accessories.....................................................................................................................4

3. OPERATION......................................................................................................................5

3.1 Commissioning................................................................................................................5

3.2 Operation ........................................................................................................................5

4. MAINTENANCE.................................................................................................................6

4.1Cleaning..........................................................................................................................6

4.2 Lubrication.......................................................................................................................6

5. SPARE PARTS..................................................................................................................7

6. TECHNICAL DATA ............................................................................................................8

Keep this for future use!

ENGLISH

PA29443A01_02_ENG Page: 2 of 8 3-2019

1. SAFETY

1.1 ....... Basic information

The basic prerequisitefor ensuring safe use and continuous operation of theCTFP-40 is knowledge of

and compliance with the safetyinstructions.

It is a question of your own safety!

All persons working with the CTFP-40 must observe the notes on safety.

In addition, rules and regulations that apply to the place of use, particularly regarding accident

prevention, must be observed.

1.2 ....... Symbols

The following symbols will be used in these operating instructions:

indicates a possible accident or injury hazard and/or possible damage to the CTFP-40.

!indicates notes on application.

1.3 ....... Dangerousness of the machine

The CTFP-40 has been constructed according to recognized technical safety regulations and has

undergone a safety examination and received official acceptance.

It is equipped with safety devices.

However, operating error and misuse could present a danger to:

•life and limb of the operator,

•the machine.

The CTFP-40 should only be used:

•for the designated application and

•in perfect condition with regard to technicalsafety.

All persons involved with commissioning, operating and maintaining the CTFP-40, must:

•be appropriately qualified and follow these operating instructionsprecisely.

1.4 ....... Designated use

The CTFP-40 is to be used exclusively for crimping wire-end ferrules with cross sections between

#24 –12AWG (0,25 and 4,0 mm²). Under no circumstances should large metal parts or similar objects

be introduced; the die set will be ruined.

Unauthorized amendments to the CTFP-40 are prohibited for safety reasons!

Observation of all instructions and compliance with the prescribed operating conditions

are part of the designated use.

ENGLISH

PA29443A01_02_ENG Page: 3 of 8 3-2019

1.5 ....... Sources of danger

The CTFP-40 must only be operated when the finger guard is screwed on. Only filtered compressed

air with a maximum pressure of 6 bar can be used.

Disconnect the machine from the compressed air before working on the CTFP-40, during breaks and

when the device is not in use. Do not pull on the compressed air tubing to disconnect.

1.6 ....... Work places

The following should be avoided for operation and storage:

•damp or dusty places,

•places which are subject to high levels of heat, direct sunlight or low temperatures:

operating range: 59°F to 95°F (15 °C to 35 °C).

Protect the compressed air tubing from heat, oil and sharp edges.

1.7 ....... Safety devices

The CTFP-40 has a finger guard at the front as a contact safety device.

Under no circumstances should this be removed.

The CTFP-40 is stopped when disconnected from the compressed air supply.

1.8 ....... Permitted operators

Only authorized and instructed operators can work on the CTFP-40. The operator is responsible to

third parties in the working area.

The owner must:

•make the operating instructions available to the operatorand

•make sure that the operator has read and understood the instructions

1.9 ....... Guarantee

In principle, our "General terms of purchase and delivery" apply. These are available to the owner

when the contract is concluded at the latest.

Guarantee and liability claims resulting from damage to personnel or property are inadmissible if the

following points have been violated:

•Non-designated use of the CTFP-40.

•Inappropriate working places.

•Inappropriate use and use which goes beyond that described in the operatinginstructions.

•Unauthorized structural amendments to the CTFP-40.

•Continued use of the CTFP-40 when a malfunction has beenestablished.

•Repairs carried outinappropriately.

!Only use original spare parts

ENGLISH

PA29443A01_02_ENG Page: 4 of 8 3-2019

2. DESCRIPTION

2.1 ....... Application

The CTFP-40 is a pneumatic crimping tool for wire-end ferrules with a cross-section of between

#24 –12AWG (0,25 and 4,0 mm²).

The CTFP-40 comprises a tabletop unit and a foot-operated switch. As both hands are free to insert

the wire fitted with wire-end ferrules, the CTFP-40 is ideally suited to pre-confectioning cables.

2.2 Components

Figure 1 - Spare Parts

1 Tabletop unit

2 Compressed air tubing

3 Foot-operated switch

4 Switch

Storage compartment for wire-end

ferrules

6 Head

7 Finger guard

8 Die set

2.3 Accessories

Table clamp

ENGLISH

PA29443A01_02_ENG Page: 5 of 8 3-2019

3. OPERATION

3.1 ....... Commissioning

•Check whether finger guard (1) is present

andis sitting firm.

•Check whether the die set (2) is free from

foreign matter.

•Check whether the pneumatic tubing nuts

(3) have been tightenedfirmly.

•Insert the table clamp (4) into thebore hole

in the tabletop unit and screw tightly to the

worktable.

•Check the compressed-air supply:

min. 4 bar, max. 6 bar filtered air

•Connect the free connection (5) on

thefoot switch to the compressed-air

supply

Figure 2 - Commissioning

3.2 ....... Operation

•Introduce stripped wire with wire-end

ferrules alreadyfitted, atthe side (1) or

fromthefront (2).

•Press the switch (3), the crimping

processwill be triggered.

•Release the switch (4), the crimped wire

canbe removed again (5).

Figure 3 - Operation

ENGLISH

PA29443A01_02_ENG Page: 6 of 8 3-2019

4. MAINTENANCE

The CTFP-40 must be

opened. Disconnect

compressed air!

4.1 ....... Cleaning

•Unscrew hexagon socket screw(1).

•Pull out the die set (2).

•Clean die set (3) and lightly oil pivot (4).

•Push in die set (5).

•Tighten hexagon socket screw(6).

Figure 4 - Cleaning

4.2 Lubrication

•Unscrew the head (1).

•Remove the spring (2) and piston(3).

•Lubricate the two arms of the die set(4) (e. g.

CHEMPLEX 746).

•Insert arms of the die set and spring.

•Insert head (5) and fasten fingertight.

Figure 5 - Lubrication

ENGLISH

PA29443A01_02_ENG Page: 7 of 8 3-2019

5. SPARE PARTS

Address:

Panduit Corp.

16530 W. 163rd St.

Lockport, IL 60441 U.S.A.

Tel. 1-800-777-3300

The following spare parts can be ordered with the

appropriate Article No.

Figure 6 - Spare parts

No.

Part

Article-No.

No.

Part

Article-No.

Compressed air tube

008137

Head part incl. screw and seal

009691

Body

001564

Axis

001569

Adhesive rubber pads

001727

Die Set

009059

Sealing ring

001135

Finger spring

001556

Piston

005121

Finger guard

009749

Spring

001555

Foot-operated switch

005541

Head complete

008688

Table clamp

001551

ENGLISH

PA29443A01_02_ENG Page: 8 of 8 3-2019

6. TECHNICAL DATA

Instrument...........................................................................................................Pneumatic Crimper

Crimping range.............................................................................#24 - #12 AWG (0,25 – 4,0 mm²)

Compressed-air connection.............................................................................................. min. 4 bar

........................................................................................................................................ max. 6 bar

Air consumption.......................................................................................0.2 liter / Crimping at 5 bar

Dimensions (diameter x length x height)................................................................. 7.8” x 5.3” x 2.9”

.........................................................................................................................(200 x 135 x 75 mm)

Weight .........................................................................................................approx. 6.2 lbs. (2.8 kg)

Acoustic pressure emissions LpA.....................................................................................< 70 dB (A)

Name plate

Panduit Corp.

18900 Panduit Drive

Tinley Park, IL 60487 USA

CTFP-40

Cross Section (working range)

Serial Number

Manufactured: MM-YY

Compliance

Country of Origin

Q. C. Number

CTFP-40 Label

Tabla de contenidos

Idiomas:

Otros manuales de Herramientas eléctricas de Panduit

Panduit

Panduit CP-881 Manual de usuario

Panduit

Panduit GS4EH Manual de usuario

Panduit

Panduit CT-2980/L Manual de usuario

Panduit

Panduit ST2MT Manual de usuario

Panduit

Panduit CA-800EZ Manual de usuario

Panduit

Panduit CP-881/E Manual de usuario

Panduit

Panduit PA24849A01 Manual de usuario

Panduit

Panduit CT-1525 Manual de usuario

Panduit

Panduit CT-260 Manual de usuario

Panduit

Panduit BlackFin CT-2920 CCP Series Manual de usuario

Panduit

Panduit PTS Manual de usuario

Panduit

Panduit GTH Manual de usuario

Panduit

Panduit RT2HT Manual de usuario

Panduit

Panduit PBTMT Manual de usuario

Panduit

Panduit CT-1090 Manual de instrucciones

Panduit

Panduit CT-400 Manual de usuario

Panduit

Panduit CT-2940 Series Manual de usuario

Panduit

Panduit ST-100 Manual de usuario

Panduit

Panduit PN433 Manual de usuario

Panduit

Panduit CP-991 Manual de usuario

Panduit

Panduit CT-1700 Manual de usuario

Panduit

Panduit GTH Manual de usuario

Panduit

Panduit CT-720 Manual de usuario

Panduit

Panduit PDM Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual