Panasonic External Presentation unit 1728 Manual de lista de piezas

Technical Description

MEW01297

Revision 2

External Presentation unit 1728,

ver. 1.4.x

Author: Jan Pettersson

Date of issue: 2010-04-08

Date of rev: 2011-08-15

This page has deliberately been left blank.

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

Table of contents

1Introduction________________________________ 3

2Definitions / Explanations ____________________ 4

3General description _________________________ 5

3.1 Ext. Presentation Unit 1728 __________________________ 5

3.1.1 SW mode 1728 - 1587___________________________ 5

3.1.2 SW mode 1728 - 1582___________________________ 5

4Selective alarm presentation __________________ 7

4.1 Ext. Presentation unit 1728___________________________ 7

5LED indicators, Push buttons, etc. _____________ 9

5.1 Ext. Presentation Unit 1728 __________________________ 9

6SW mode & Address setting _________________ 12

6.1 SW mode setting__________________________________ 12

6.1.1 SW mode setting via jumper "J4" _________________ 13

6.2 Address setting ___________________________________ 13

6.2.1 Address setting mode via the c.i.e. ________________ 14

6.3 Flow chart _______________________________________ 14

7User definable text messages (alarm texts)______ 16

8Commissioning a new unit / SSD download_____ 17

9Restart ___________________________________ 19

10 Fault messages_____________________________ 21

10.1 Fault messages in the Ext. Presentation Unit (EPU) ______ 21

10.2 Fault messages in the c.i.e. __________________________ 21

10.2.1 System EBL512 ______________________________ 21

10.2.2 System EBL128 ______________________________ 22

10.2.3 System EBL512 G3____________________________ 22

11 Disablement message _______________________ 24

12 Software (S/W) ____________________________ 25

12.1 S/W version______________________________________ 25

12.2 S/W download____________________________________ 26

13 Operation_________________________________ 27

14 Connections_______________________________ 29

15 Technical data_____________________________ 31

15.1 Power supply_____________________________________ 31

15.2 RS485 __________________________________________ 31

15.2.1 Cable _______________________________________ 31

15.3 RS232 __________________________________________ 31

15.4 Connection ______________________________________ 31

15.5 Current consumption_______________________________ 32

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

16 Revision history____________________________ 33

This page has deliberately been left blank.

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

1 Introduction

This document

describes the External Presentation unit 1728

(Informationstablå). The shorter expression EPU will also be used in

this document.

The 1728 unit can run in one of two SW modes:

SW mode 1728 - 1587

SW mode 1728 - 1582

See chapter "General description", page 5.

System EBL128 and EBL512

This document is valid for the 1728 software version 1.4.x, which

require a software version > 2.3.2 in EBL512 and a software version >

1.0.5 in EBL128 only if the functions described below are to be used.

The 1728 software version 1.4.x can be used in the systems EBL512

and EBL128 with lower versions but then without the possibility to

use these functions.

Functions

- The buzzer will sound (continuously) for any not acknowledged fault

in the system or a fault in the unit.

- Push button "Silence buzzer" will silence the buzzer.

- Disablement(s) in the system will be presented as "General

disablement in system".

System EBL512 G3

The 1728 software version 1.4.x has to be used in the system EBL512

G3.

Original file name: L:\User documents\EBL\Doc\Eng\MEW01297 (Rev

2).doc

Not valid for the Swedish convention (SBF).

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

2 Definitions / Explanations

Definitions / explanations / abbreviations / etc. frequently used or not

explained elsewhere in the document.

EPU External Presentation Unit

C.i.e. Control and indicating equipment (=control unit)

C.U. Control unit (=Control and indicating equipment)

S/W Software

H/W Hardware

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

3 General description

The ext. Presentation unit is intended for pre-warning, co-incidence,

fire and heavy smoke / heat alarm presentation. Any fault in the

system will be presented as "General fault in system".

Any disablement in the system will be presented as "General

disablement in system".2

3.1 Ext. Presentation Unit 1728

Figure 1. Left: The External Presentation Unit 1728SE has a

Swedish front. Right: 1728UK has an English front.

The enclosure is made of grey (RAL 7035) high impact ABS, with

temperature resistance up to 85° C. Fitted with a supplementary "O"

ring gasket, it will comply with IP65, in respect of dust and moisture.

Dimensions (W x H x D): 220 x 145 x 50 mm.

The Ext. Presentation unit shall be wall mounted.

3.1.1 SW mode 1728 - 1587

This SW mode has the highest performance with regard to

functionality, response time, ability to store fire alarms, etc.

The Ext. Presentation unit 1728SE, running in SW mode 1728 –1587,

is intended to succeed the existing Display unit 2236SE and the

External presentation display 2428SE.

In system EBL512, 1728 units running in SW mode 1728 –1587 have

to be connected to an Ext. FBP / DU interface board 1587 mounted

in the EBL512 c.i.e. EBL512 software version > 2.2 is required.

In system EBL128, 1728 units running in SW mode 1728 –1587 are

connected directly to the main board but an optional RS485

transceiver component 4552 is required on the main board.

In system EBL512 G3, 1728 units running in SW mode 1728 –1587

are connected directly to the main board connector "J4".

3.1.2 SW mode 1728 - 1582

The Ext. Presentation unit 1728SE, running in SW mode 1728 –1582,

is intended to be a spare part for the existing External presentation

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

display 2428SE. Note, the functionality / performance is the same but

the size, the look and the front layout are different.

In system EBL512, 1728 units running in SW mode 1728 –1582 have

to be connected to an Ext. FBP interface board 1582 mounted in the

EBL512 c.i.e.

In systems EBL128 and EBL512 G3, 1728 units running in SW mode

1728 –1582 can NOT be connected.

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

4 Selective alarm presentation

Normally all fire alarms will be presented in the c.i.e:s, ext. FBPs and

Presentation units, etc. There are some possibilities to select which

alarms that shall be presented in each unit. It is also programmable, if

the fire alarm presentation shall be according to EN54, i.e. when only

one point in a zone is in alarm status it will be presented as a point

alarm (zone and address), else presented as a zone alarm.

4.1 Ext. Presentation unit 1728

The alarm presentation in 1728 will be like in the c.i.e. that it is

connected to, i.e. point alarm or zone alarm presentation. See the

Operating Instructions, chapter "Fire alarm" for the system

respectively.

Via Win512 / Win128 / Win512 G3, it is possible to select which

alarms that shall be presented in the unit respectively. For example, if

there are many buildings in an installation, the units in one specific

building shall only present alarms activated within this building.

The following, so called operands are available (CU alternatives not

valid for EBL128):

1. Control unit (CU)

2. Consecutive control units (CU1, CU2)

3. Zone (zone)

4. Consecutive zones (zone1, zone2)

5. Zone –address (zone, addr)

6. Consecutive zone –addresses (zone1, addr1, zone2, addr2)

Explanations:

1. CU = Control unit number (c.i.e. no. 00-29)

2. CU1 = The first control unit number in the sequence. CU2 = The

last control unit number in the sequence.

3. zone = Zone number (001-999) In EBL128 (01-32).

4. zone1 = The first zone number in the sequence. zone2 = The last

zone number in the sequence.

5. zone, addr = Zone number and address within the zone (001, 01 –

999, 99)

6. zone1, addr1 = The first zone number and address in the sequence.

zone2, addr2 = The last zone number and address in the sequence.

Up to 50 operands can be used to make a, so called selector for an ext.

Presentation unit. Here follows a selector example:

Control unit (00), Consecutive zones (100, 500), Zone –address

(900, 01) In this 1728 unit will only be presented alarms that origin

from the c.i.e. no. 00 or from zone 100 up to and including zone 500

or from the alarm point 900-01.

Panasonic Electric Works Nordic AB

MEW01297 Rev: 2 Technical Description External Presentation Unit 1728, ver. 1.4.x

Default in systems EBL512 and EBL512 G3 is: Control units (00,

29), i.e. all alarms from all c.i.e:s will be presented in all ext.

Presentation units 1728.

Default in system EBL128: Zones (01 - 32), i.e. all alarms will be

presented in all ext. Presentation units 1728.

Otros manuales para External Presentation unit 1728

Tabla de contenidos

Otros manuales de Sistema de seguridad de Panasonic

Panasonic

Panasonic 1735 Manual de lista de piezas

Panasonic

Panasonic EBL128 Manual de usuario

Panasonic

Panasonic KX-HGW600 Manual de usuario

Panasonic

Panasonic VIDEOLARM PCF5 Hoja de instrucciones

Panasonic

Panasonic AW-HE100 Manual de usuario

Panasonic

Panasonic SF4B C Series Manual de usuario

Panasonic

Panasonic WV-SC386 Manual de usuario

Panasonic

Panasonic WVCP230 - CCD 120V Manual de usuario

Panasonic

Panasonic WJ-ND300A/10000V Manual de servicio

Panasonic

Panasonic BL-WV10 Manual de usuario

Panasonic

Panasonic WJ-NV200 Manual de usuario

Panasonic

Panasonic External Presentation unit 1728 Manual de lista de piezas

Panasonic

Panasonic WV-CW4C Manual de usuario

Panasonic

Panasonic WV-AS710 Manual de usuario

Panasonic

Panasonic WV-PB5564E Manual de usuario

Panasonic

Panasonic KX-HNS101 Manual de usuario

Panasonic

Panasonic Fire Alarm Systems Heat Detectors 6275 Manual de usuario

Panasonic

Panasonic KX-HNS105 Manual de usuario

Panasonic

Panasonic BL-WV10 Manual de usuario

Panasonic

Panasonic WJ-ND400/1000 Manual de servicio

Panasonic

Panasonic KX-HNS105AZ Manual de usuario

Panasonic

Panasonic 4414 Manual de usuario

Panasonic

Panasonic VL-GC001A Instrucciones de funcionamiento

Panasonic

Panasonic Alert annunciation unit 1736 Manual de lista de piezas

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario