Panasonic WV-PB5564E Manual de usuario

-1-

Alarm Board

WV-PB5564E

Before attempting to connect or operate this product, please read these instructions completely

PREFACE

The WV-PB5564E Alarm Board is provided for expanding the system capability of the Matrix

Switcher.

When handling this board, hold only by circuit board edges. Otherwise components on the

board may be damaged by static electricity.

Caution

APPEARANCE

1. Alarm Number display

This display indicates the alarm input number when the associated alarm sensor unit is activat-

ed.

Note: The display indicator lights up as shown below When the alarm number is over one hun-

dred.

2. Mode Selection Switch (MODE)

This rotary switch, in combination with the test switch, is used to select the alarm test mode.

Mode 0: Press the Test Switch to receive, from memory, a chronologically organized display (in

the Alarm Number Display) of all alarms received from the Alarm Input Connector.

Mode 1: Press the Test Switch to simulate receiving alarm inputs 1-64 in ascending order, one

alarm per second. Use this mode to test the system for Alarm Mode-1, Mode-2 or Mode-3

set up.

Mode 2: Press the Test Switch to simulate receiving alarm inputs 1-64 all at the same time. Use

this mode to test the system for Alarm Mode-1, Mode-2 or Mode-3 set up.

Mode 3-9: These modes are not available.

Note: The alarm inputs 65-128 are activated above modes if the SW1 on the board is set at

alarm number 65-128. Refer to the BOARD SETTING on page 2.

3. Test Switch (TEST)

This switch is used to run the alarm test mode in combination with the Mode Selection Switch.

4. Reset Switch (RESET)

This switch is used to stop the alarm test mode or clear alarm the records from the internal

memory.

33-64

ALARM

TEST

1-32

RESET

MODE

0 0

indicator

BOARD

NO.

Pin No.Pin No.

-2-

(Close) Alarm Sensor(Open) Alarm Sensor

Normal Condition Alarm In Alarm Signal

Normally Open

(NOR OPEN)

t 100 msec.

Normally Closed

(NOR CLOSE)

(Close) Alarm Sensor (Open) Alarm Sensor t 100 msec.

Alarm 1(65)

Alarm 2(66)

Alarm 3(67)

Alarm 4(68)

Alarm 5(69)

Alarm 6(70)

Alarm 7(71)

Alarm 8(72)

Alarm 9(73)

Alarm 10(74)

Alarm 11(75)

Alarm 12(76)

Alarm 13(77)

Alarm 14(78)

Alarm 15(79)

Alarm 16(80)

Alarm 17(81)

Alarm 18(82)

Alarm 19(83)

Designation

Pin No.

Alarm 20(84)

Alarm 21(85)

Alarm 22(86)

Alarm 23(87)

Alarm 24(88)

Alarm 25(89)

Alarm 26(90)

Alarm 27(91)

Alarm 28(92)

Alarm 29(93)

Alarm 30(94)

Alarm 31(95)

Alarm 32(96)

Not used

Ground

Designation

Alarm 33(97)

Alarm 34(98)

Alarm 35(99)

Alarm 36(100)

Alarm 37(101)

Alarm 38(102)

Alarm 39(103)

Alarm 40(104)

Alarm 41(105)

Alarm 42(106)

Alarm 43(107)

Alarm 44(108)

Alarm 45(109)

Alarm 46(110)

Alarm 47(111)

Alarm 48(112)

Alarm 49(113)

Alarm 50(114)

Alarm 51(115)

Designation

Pin No.

Alarm 52(116)

Alarm 53(117)

Alarm 54(118)

Alarm 55(119)

Alarm 56(120)

Alarm 57(121)

Alarm 58(122)

Alarm 59(123)

Alarm 60(124)

Alarm 61(125)

Alarm 62(126)

Alarm 63(127)

Alarm 64(128)

Not used

Ground

Designation

1-32

33-64

OFF

1-64

65-12

ALARM

INPUT NO. SW1 SETTING

BOARD SETTING

Before installing this board, the following settings should be made by qualified service personnel or system installers.

1. Set switches (SW1) on the board to meet the alarm input number as shown below.

OFF

SW1

UNIT ADR

5. Alarm Input Connector (1-32, 33-64)

This connector accepts the alarm signals, either normally open or normally closed, from the associated alarm sensor unit.

-3-

3. Confirm switchers (SW12) on the board are set to the following positions.

OFF

SW12

These switches are used only for factory test.

Always keep these switches in the "OFF" positions in the

field.

Note

2. Set switches (SW4 - SW11) on the board to meet the

alarm input requirements. Initially, normally open

(NOR, OPEN) positions are selected at the factory.

12345678

OFF

SW4

NOR

OPEN

12345678

OFF

SW5

SW4

SW5

SW6

SW7

SW8

SW9

SW10

SW11

Switch No.

1 - 8 (65-72)

9 - 16 (73-80)

17 - 24 (81-88)

25 - 32 (89-96)

33 - 40 (97-104)

41 - 48 (105-112)

49 - 56 (113-120)

57 - 64 (121-128)

Alarm Input

OFF

SW1

OFF

SW12

UNIT ADR

SW4

SW5

SW6

SW7

SW8

SW9

SW10

SW11

The following installation should be made by qualified ser-

vice personnel or system installers.

1. Remove the screws from the rear panel(s) of the

Matrix Switcher.

2. Remove the rear panel(s).

3. Place the Alarm Board into the desired position in the

rear of Matrix Switcher by sliding it inside the board

quides.

INSTALLATION

Before installing this board be sure to turn off the Power

Switch of the Matrix Switcher.

Caution

Each slot is identical, so the board can installed in any

slot.

However it is recommended to install the board as

shown below for an orderly installation.

Note

Rear Panel(s)

Remove screws.

4. Make sure to push in the Alarm Board until it is seated

firmly.

5. Secure the Alarm Board by tightening the two screws

on the board.

6. Close off open spaces on the rear of the Matrix

Switcher by using WV-Q63E Blank Panels (Optional)

or supplied rear panel(s).

(Refer to the instructions for WV-Q63E)

Refer to the Operating Instructions of WJ-SX550A for

more details.

Note

SPECIFICATIONS

Alarm Input (1 - 64): Normally open or normally closed selectable

(contact time more than 100 msec.)

37 pin D-Sub connector (x2)

Dimensions: 24.5(W) x 265(H) x 260(D) mm

15/16"(W) x 10-7/16"(H) x 10-1/4"(D)

Weight: 400g(0.9 lbs.)

Weight and dimensions indicated are approximate.

specifications are subject to change without notice.

N1094-1026 YWV8QA3426BN Printed in Japan

N 19

Matsushita Electric Industrial Co., Ltd.

Central P.O. Box 288, Osaka 530-91, Japan

Blank Panel

Tighten screws.

Alarm Board

Alarm Board WV-PB5564

Video Input

Board Video Output

Board

CPU

RS-232C

TIME

ADJUST IN

COM

PRINTER

OUT

VS/VD

OUT

OFF

+9V

+5V

−

POWER

11A00001

OUT

MONITOR

ALARM OUT

RESET OUT

EXT TIMING IN

RECOVER IN

OUTPUT

MONITOR

ALARM OUT

RESET OUT

EXT TIMING IN

RECOVER IN

MONITOR

ALARM OUT

RESET OUT

EXT TIMING IN

RECOVER IN

MONITOR

ALARM OUT

RESET OUT

EXT TIMING IN

RECOVER IN

OUT

OUTPUT

OUT

OUTPUT

OUT

OUTPUTINPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

INPUT

CAMERA IN

VIDEO OUT1

VIDEO OUT2

33-64

ALARM

TEST

1-32

RESET

MODE

CONTROL

DATA 1

DATA 2

DATA 3

DATA 4

DATA 5

DATA 6

DATA 7

DATA 8

TEST 1

TEST 2

Tabla de contenidos

Otros manuales de Sistema de seguridad de Panasonic

Panasonic

Panasonic EBL128 Manual de usuario

Panasonic

Panasonic Alert annunciation unit 1736 Manual de lista de piezas

Panasonic

Panasonic 4414 Manual de usuario

Panasonic

Panasonic BL-WV10 Manual de usuario

Panasonic

Panasonic BB-HGW700A - Network Camera Router Manual de usuario

Panasonic

Panasonic KX-HNS105 Manual de usuario

Panasonic

Panasonic KX-HNS105AZ Manual de usuario

Panasonic

Panasonic WJ-HDE400 Manual de usuario

Panasonic

Panasonic KX-HGW600 Manual de usuario

Panasonic

Panasonic KX-HNS105 Manual de usuario

Panasonic

Panasonic External Presentation unit 1728 Manual de lista de piezas

Panasonic

Panasonic Fire Alarm Systems Heat Detectors 6275 Manual de usuario

Panasonic

Panasonic AW-HE100 Manual de usuario

Panasonic

Panasonic WJ-ND400/1000 Manual de servicio

Panasonic

Panasonic BL-WV10A Manual de usuario

Panasonic

Panasonic External Presentation unit 1728 Manual de lista de piezas

Panasonic

Panasonic WV-SC386 Manual de usuario

Panasonic

Panasonic WJ-ND300A/10000V Manual de servicio

Panasonic

Panasonic WV-AS710 Manual de usuario

Panasonic

Panasonic WV-CW4C Manual de usuario

Panasonic

Panasonic WJ-NV200 Manual de usuario

Panasonic

Panasonic A02-ACAM3KIT Manual de usuario

Panasonic

Panasonic KX-HNS101 Manual de usuario

Panasonic

Panasonic 4350 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario