Panasonic K-EF134L02E Manual de usuario

HD IR Weatherproof Network Dome Camera

Quick Start Guide

Model No. K-EF134L02E

K-EF134L03E

K-EF134L06E

Version 1.0.2

Welcome

Thank you for purchasing our network camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated DC12V in the IEC60950-1. (Refer to general introduction)

Please note: Do not connect two power supplying sources to the device at the same time;

it may result in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper

handling or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (MOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (MOS) optical component damage.

Please keep the sound ventilation.

Thunder-proof device is recommended to be adopted to better prevent thunder.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily

maintenance work.

Do not touch the CCD (MOS) optic component. You can use the blower to clean the dust on the

lens surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water

to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to

clean the device.

Please put the dustproof cap to protect the CCD (MOS) component when you do not use the

camera.

Dome enclosure is the optical component, do not touch the enclosure when you are installing the

device or clean the enclosure when you are doing maintenance work. Please use professional

optical clean method to clean the enclosure. Improper enclosure clean method (such as use

cloth) may result in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation template label

Important Safety Instructions

iii

Table of Contents

1Structure ......................................................................................................................................1

1.1 Components..................................................................................................................1

1.2 Framework and Dimension.........................................................................................2

2Device Installation ......................................................................................................................3

2.1 Installation Steps for Plastic Dome............................................................................3

2.2 Restore Factory Default Setup Introduction.............................................................5

3Quick Configuration Tool...........................................................................................................6

3.1 Overview........................................................................................................................6

3.2 Operation.......................................................................................................................6

4Web Operation............................................................................................................................8

4.1 Network Connection.....................................................................................................8

4.2 Login and Main Interface.............................................................................................8

1Structure

1.1 Components

You can refer to the following figure for multiple-function combination cable information. See Figure

1-1.

Figure 1-1 Multiple-function combination cable

No.

Portname

Function

Connection

Note

LAN

Network

port

Ethernet

To connect to standard

Ethernet cable.

DC12V

Power input

port

Power input port. Input DC

12V.

No.

Component Name

Device lens

Dome body

Dome enclosure

1.2 Framework and Dimension

Please refer to the following two figures for dimension information. The unit is mm. See Figure 1-2 and

Figure 1-3.

Figure 1-2 Dimension illustration 1

Figure 1-3 Dimension illustration 2

2Device Installation

Important

•Make sure that the installation area is strong enough to hold the product, such as a concrete

ceiling.

•Install the camera in the foundation area of the architecture or where sufficient strength is

assured.

•If a wall or ceiling board such as plasterboard is too weak to support the total weight, the area

shall be sufficiently reinforced.

Please see Figure 2-1 and Figure2-2.

2.1 Installation Steps for Plastic Dome

Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference.

Step 1

Rotate decoration ring clockwise and take it out.

Step 2

Affix the installation template label (accessory) to the ceiling or wall, and use a pen to mark the

positions of the screws and cable mounting hole in the ceiling or wall. Remove the installation template

label and attach the camera with 3 screws (locally procured).

Step 3

Loosen the M3X8 cross pan head screw on pedestal, and be careful do not loosen completely. Now

you can adjust position according to monitoring area. After adjustment, fasten the M3X8 cross pan

head screw with sheeting.

Step4

Rotate decoration ring bottom up and face the three spigots toward the three slots. When you hear a

“Ca” sound, it is rotated in place.

Figure 2-1 Device installation illustration 1

Important

Please pay attention to the dome camera direction when you are installing. Please refer to the

following figure for detailed information. See Figure 2-2.

Figure 2-2 Device installation illustration 2

Note

This series product supports two cable exits. One is from the bottom and the other is from the

side. Please refer to the following figure for cable exit from the side information.

Figure 2-3 Device installation illustration 3

2.2 Restore Factory Default Setup Introduction

Important

Please use RESET button when device is running.

Step1

Please refer to step1 and step2 in chapter 2.1 to loose the dome body. Push a little bit; you can take

the dome body from the gland cover.

Step2

Take the dome body out and then turn the top cover hard to remove.

Step3

Slightly press the RESET button to complete the reset function. See Figure 2-4.

Step4

Turn the top cover back to the original position. Please make sure it reaches the original position,

otherwise it may result in water leakage!

Step5

Put the dome back to the gland cover. Please refer to step4 in chapter 2.1 to install the decoration ring

back.

Figure 2-4 Reset

3Quick Configuration Tool

3.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can

use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

3.2 Operation

Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 3-1.

In the device list interface, you can view device IP address, port number, subnet mask, default

gateway, MAC address and etc.

Figure 3-1 Search interface 1

Select one IP address and then right click mouse, you can see an interface is shown as in Figure 3-2.

Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 3-2 Search interface 2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Panasonic

Panasonic

Panasonic WV-S1132 Manual de funcionamiento

Panasonic

Panasonic BL-C210 Series Manual de usuario

Panasonic

Panasonic WVNP244 - COLOR CCTV CAMERA Manual de usuario

Panasonic

Panasonic BB-HCE481A - Network Camera Manual de funcionamiento

Panasonic

Panasonic AW-HE120KE Manual de usuario

Panasonic

Panasonic WV-CW374 Manual de usuario

Panasonic

Panasonic WV-CL930 Series Manual de usuario

Panasonic

Panasonic WVNF302 - NETWORK CAMERA Manual

Panasonic

Panasonic WV-CP240EX Manual de usuario

Panasonic

Panasonic WV-CW970 Manual de usuario

Panasonic

Panasonic WVCW474F - COLOR CCTV CAMERA Manual de usuario

Panasonic

Panasonic WV-NW502S Manual de usuario

Panasonic

Panasonic WV-CF314LE Series Manual de usuario

Panasonic

Panasonic AKHC910 - 1080I CAMERA Manual de usuario

Panasonic

Panasonic GP-KR222E Manual de usuario

Panasonic

Panasonic WV-CP110E Manual de usuario

Panasonic

Panasonic BB-HCM580A Manual de usuario

Panasonic

Panasonic WVBP330 - B/W CCTV CAMERA Manual de usuario

Panasonic

Panasonic WV-SW598APJ Manual de usuario

Panasonic

Panasonic OneHome KX-HCM110A Manual de usuario

Panasonic

Panasonic KX-HCM10 Manual de usuario

Panasonic

Panasonic AJ-HDC27FE Manual de usuario

Panasonic

Panasonic WV-SP500 Series Manual de usuario

Panasonic

Panasonic WV-SW598 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario