Panasonic AWE300S - SEPERATE CAMERA Manual de usuario

OPERATING INSTRUCTIONS

Before attempting to connect, operate or adjust this product, please

read these instructions completely.

1/3-inch Camera With Separate Head

Model AW- P

FOCUS

LOCK

indicates safety information.

CAUTION

RISK OF ELECTRIC SHOCK

O NOT OPEN

CAUT ON: TO REDUCE THE R SK OF ELECTR C SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERV CEABLE PARTS NS DE.

REFER TO SERV C NG TO QUAL F ED SERV CE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (service)

instructions in the literature accompanying the appliance.

WARNING:

TO RE UCE THE RISK OF FIRE OR SHOCK HAZAR , O NOT

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

CAUTION:

TO RE UCE THE RISK OF FIRE OR SHOCK HAZAR AN ANNOYING

INTERFERENCE, USE THE RECOMMEN E ACCESSORIES ONLY.

FCC Note:

This device complies with Part 15 of the FCC Rules. To assure continued

compliance follow the attached installation instructions and do not make any

unauthorized modifications.

This equipment has been tested and found to comply with the limits for a class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . 4

Features. . . . . . . . . . . . . . . . . . . . . . . . . . 4

Special Notes on Operation. . . . . . . . . . 5

Precautions . . . . . . . . . . . . . . . . . . . . . . . 6

Parts and Their Functions . . . . . . . . . . . 7

$Main unit . . . . . . . . . . . . . . . . . . . . . . 7

$Camera head unit . . . . . . . . . . . . . . . 9

Installation. . . . . . . . . . . . . . . . . . . . . . . 10

$Attaching the lens . . . . . . . . . . . . . . 10

$nstallation on a camera stand

(tripod, etc.) . . . . . . . . . . . . . . . . . . . 10

System Configuration (Connections)

. . . 11

$Connecting equipment with a

composite video input connector. . . 11

$Connecting a remote control unit

(RCU) . . . . . . . . . . . . . . . . . . . . . . . 12

$Connecting a remote control box

(RCB) . . . . . . . . . . . . . . . . . . . . . . . 13

$Connecting multiple cameras

(achieving genlock) . . . . . . . . . . . . . 14

$Connections for exercising control

from a computer . . . . . . . . . . . . . . . 15

$Reference: Model numbers of related

equipment . . . . . . . . . . . . . . . . . . . . 16

Operating Mode Selection . . . . . . . . . . 17

How to select the operating mode

. . 18

Operating Procedures . . . . . . . . . . . . . 19

Adjustments . . . . . . . . . . . . . . . . . . . . . 20

$Flange back adjustment . . . . . . . . . 20

$White balance adjustment. . . . . . . . 21

$Black balance adjustment . . . . . . . . 23

$Black level (total pedestal)

adjustment. . . . . . . . . . . . . . . . . . . . 24

$Genlock adjustment. . . . . . . . . . . . . 25

Menu Item Settings and Changes . . . . 27

$Setting the menu items . . . . . . . . . . 27

Halogen light, fluorescent light and

outdoor mode sub-menu screens

. . . 29

$User mode sub-menu screens . . . . 35

Returning to Initial Settings. . . . . . . . . 42

$nitial settings (factory settings). . . . 43

Outline rawings . . . . . . . . . . . . . . . . . 45

$Main unit . . . . . . . . . . . . . . . . . . . . . 45

$Camera head unit . . . . . . . . . . . . . . 45

Specifications . . . . . . . . . . . . . . . . . . . . 46

$Accessories. . . . . . . . . . . . . . . . . . . 47

Introduction

OFeaturing digital video signal processing, this 1/3-inch 3-CCD system color camera with

its separate head achieves a high picture quality and high reliability as well as many and

varied functions despite its compact size and light weight.

OThe head is separate which means that it can easily be mounted on a microscope (C

mount), for instance.

OUsing a menu screen format, the camera’s shooting conditions and functions can easily

be set and changed.

OThe camera can be connected to a peripheral unit such as an RCB or RCU for

expanding the capabilities of the system to suit the intended applications.

OA wide range of applications can be supported by installing optional cards.

Features

High picture quality, high reliability, many and varied functions, a compact size and

light weight achieved by incorporating digital video signal processing

OResolution: 800 lines (high band DTL ON), S/N ratio: 62 dB (DNR ON)

OMinimum illumination: 1.5 lux (f/1.4 ‘night eye’ mode)

Many and varied functions despite compact size

OSetting of camera parameters using menu screens enabled

OAuto functions such as ATW, ELC and AGC incorporated

OCCD readout (field, frame) switching supported

The vertical resolution can be improved by switching to the frame mode, and this is

useful for capturing still images and other kinds of image processing.

OSynchro scan function provided to reduce horizontal line noise when computer screens

are shot

OFunctions for controlling camera by computer incorporated

OExtension of cable (standard length of 3 meters) between head unit and main unit up to

10 meters possible

Faithful image reproduction assured by many compensation circuits

OEven areas with dark colors reproduced clearly by chroma detail enhancement

ONatural detail enhancement enabled even for dark areas by dark detail circuit

ONatural dynamic range reproduced by digital highlight chroma

OFaithful reproduction of colors enabled by digital color matrix

Full spectrum of video productions supported

OConditions optimally suited to each application selectable from 4 operation modes

(halogen light mode, fluorescent light mode, outdoor mode and user mode)

OSMPTE color bar display provided

ORemote control enabled by RCU or RCB

Special Notes on Operation

OTurn the power off before connecting or disconnecting cables.

OConnection or disconnection of any studio cable, RCB cable or other cable to any unit of

equipment must be performed while power is off.

While the camera is in automatic mode:

OShooting of bright objects in ELC operation mode may result in a smeared picture

unique to the CCD.

OThe ATW function under fluorescent illumination can adversely change the white

balance.

Precautions

ODo not attempt to disassemble the camera, Remote Control Unit (RCU) or other units.

n order to prevent electric shock, do not remove screws or covers. There are no user-

serviceable parts inside.

ODo not mishandle the camera. Avoid striking, shaking, etc. The camera contains

precision components which could be damaged by improper handling or storage.

ODo not let the lens remain uncovered when the camera is not in use. f the lens is not

installed, do not leave the lens mount hole uncovered.

ODo not touch the surface of the lens or prism.

ODo not use strong or abrasive detergents when cleaning the camera body.

ODo not aim the camera toward the sun, irrespective of whether it is turned on or not.

ODo not expose the camera or Remote Control Unit (RCU) to rain or moisture, and do not

try to operate the equipment in wet conditions. Do not operate the camera or RCU if it is

wet.

ODo not operate the camera or Remote Control Unit (RCU) outdoors during a thunder

storm.

ODo not use the camera where it will be subject to high temperatures or high humidity.

ODo not leave the camera and Remote Control Unit (RCU) turned on when not in use. Do

not unnecessarily turn the camera power on and off repeatedly. Do not block the

ventilation slots.

ORefer any servicing to qualified service personnel.

OHandle the camera with care.

OPlace the lens cap on the lens when the camera is not in use. f the lens is not installed,

protect the surface of the prism by placing the body cap over the lens mount hole.

OUse a mild blower or lens cleaning tissue designed for coated lenses to clean the

surface of the lens or prism if it requires cleaning.

OUse a dry cloth to clean the camera if it is dirty. f the dirt is hard to remove, use mild

detergent and wipe gently.

OUse caution when operating the camera near spot lights or bright lights, as well as any

objects and surfaces which may reflect light.

Of the camera or RCU gets wet, turn the power off immediately and have the unit

checked by an authorized service facility.

OFollow normal safety precautions to avoid personal injury.

OUse the camera in an environment where the temperature is within 14°F to 113°F

(–10°C to +45°C), and the relative humidity is within 30 % to 90 %.

OAlways turn the power off when the camera is not going to be used. Operate the

camera and RCU only when there is adequate ventilation.

OOperating a wireless device that generates powerful radio waves near the camera may

adversely affect the output images.

$Main unit

OPT ON CARD

TEM / AWC

YES / ASC

NO / BAR

V DEO OUT

G / L N

/ F REMOTE

R S

DC12V N

;

Parts and Their Functions

1Cable connector

This is used to connect the camera to the camera head unit using a cable.

2MENU switch [MENU (t)]

The menu will appear on the screen when this switch is pressed for about 5 seconds.

When it is pressed while a menu is displayed, the menu item immediately above is

selected.

3ITEM/AWC switch [ITEM/AWC (y)]

When this switch is pressed while a menu is displayed, the menu item immediately

below is selected. While a menu is not displayed (when the camera is in the shooting

mode), it serves as the automatic white balance control (AWC) switch.

4YES/ABC switch [YES/ABC (+)]

When this switch is pressed while a menu is displayed, the sub-menu of a menu item

appears on the screen. When it is pressed while a sub-menu is displayed, the higher of

the two settings shown is selected. While a menu is not displayed, it serves as the

automatic black balance control (ABC) switch.

5NO/BAR switch [NO/BAR (–)]

When this switch is pressed while the main menu is displayed, the next item down can

be selected. When it is pressed while a sub-menu is displayed, the lower of the two

settings shown is selected. When it is pressed for about 5 seconds while a menu is not

displayed, the color bar signals and camera (shooting mode) are switched.

Parts and Their Functions

6Video output connector [VI EO OUT]

The composite video signals are output from this connector.

(1 V [p-p], 75 Ω, BNC connector)

7Iris connector [IRIS]

This is the standard input connector of the lens which comes with an auto iris function.

8Interface/remote connector [I/F REMOTE]

This is used to connect the remote control unit (RCU: WV-RC700A or WV-RC550),

remote control box (RCB: WV-CB700A), etc.

The AW-CA50A26 RCU cable is required to connect the WV-RC700A or WV-RC550.

The AW-CA50T10 RCB cable is required to connect the WV-CB700A.

9Power LE

This lights up red when DC power is supplied to the DC 12V input socket :.

:C 12V input socket [ C 12V IN]

The DC 12 V power supply (2 A or above) is connected here using the AW-CA4T1 DC

power cable.

;Cable clamp

This clamps the AW-CA4T1 DC power cable which has been connected to the DC 12V

input socket :to prevent the cable from becoming disconnected.

<Genlock input connector [G/L IN]

The external sync (black burst) signals are supplied to this connector to achieve genlock

with the camera.

=Option card slot

This slot is used by the option cards.

For further details, refer to the operating instructions of the option card concerned.

?> @

FOCUS

LOCK

FOCUS

LOCK

$Camera head unit

Parts and Their Functions

>Lens mount

A 1/3-inch C mount lens or microscope adapter, etc. is attached here.

?Flange back adjust screw [FOCUS/LOCK]

When the flange back needs to be adjusted, remove the cap, loosen the LOCK screw,

and adjust by turning the FOCUS screw. (Adjustment range: ±0.2 mm)

Upon completion of the adjustment, re-tighten the LOCK screw.

@Cable connector

This is used to connect the head unit to the main unit using a cable.

ACamera mounting adapter

(mounting screw holes: M2.6a10, spring washers provided)

This is used to secure the head unit when it is to be installed on a wall or ceiling or a

tripod is to be used. The head unit can be mounted on the top or bottom surface.

Otros manuales para AWE300S - SEPERATE CAMERA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Panasonic

Panasonic

Panasonic KX-HNC200FX Manual de usuario

Panasonic

Panasonic AWHE60H Manual de usuario

Panasonic

Panasonic WV-BF320 Manual de usuario

Panasonic

Panasonic WV-CP410 Manual de usuario

Panasonic

Panasonic WV-CS850 Manual de usuario

Panasonic

Panasonic KX-HCM230 Manual de usuario

Panasonic

Panasonic GP-US932CA Manual de usuario

Panasonic

Panasonic WV-SF549 Manual de usuario

Panasonic

Panasonic CV-CPW100 Series Manual de usuario

Panasonic

Panasonic SDIII Manual de usuario

Panasonic

Panasonic WV-CF284T Manual de usuario

Panasonic

Panasonic WV-CF504 Manual de usuario

Panasonic

Panasonic BB-HCM381 Instrucciones de funcionamiento

Panasonic

Panasonic BL-C160 Manual de usuario

Panasonic

Panasonic WV-SFV311 Manual de usuario

Panasonic

Panasonic AW?HE60SN Manual de usuario

Panasonic

Panasonic WV-NP304E Manual de usuario

Panasonic

Panasonic WV-SW175 Manual de usuario

Panasonic

Panasonic BB-HCM515A Manual de usuario

Panasonic

Panasonic Super Dynamic III WV-CS950 Manual de usuario

Panasonic

Panasonic WV-SW558 Manual de usuario

Panasonic

Panasonic WV-BP142 Manual de usuario

Panasonic

Panasonic BL-C230 Series Manual de usuario

Panasonic

Panasonic WV-SPV781L Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario