Outback Excel Onyx 2 Manual de usuario
EX311
Assembly and Operating Instructions for Outback®
Excel Onyx 2 Burner Gas BBQ
Photographs are not to scale.
Specifications subject to change
without prior notice.
WARNING
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow instructions
could result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children and pets
away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions
may be dangerous and will invalidate your warranty. This does not affect your
statutory rights.
Retain these instructions for future reference.
Leak test annually, and whenever the gas bottle is removed or replaced. Check
that the hose connections are tight and leak test each time you reconnect the
gas bottle.
For Flare-up control please refer to the ‘OPERATION’ section of this manual.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1. Do not store or use petrol or other
flammable vapours or liquids in the vicinity
of this or any other appliance.
2. A gas bottle not connected for use must not
be stored in the vicinity of this or any other
appliance.
0359
2
Parts List
Quantity varies according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see the corresponding ‘Hardware Reference Diagram’.
Pre-Assembled Component
Quantity varies according to model purchased
Appearance, size, and construction may differ according to model purchased
CODE PART QTY OUTBACK®
EXCEL ONYX 2 BURNER GAS
HOOD
A1 Hood (Pre-Assembled to Body)
1 √
A2 Hood Handle 1 √
A3 Warming Rack 1 √
A4 Heat Indicator 1 √
BODY
B1 Barbecue Body 1 √
B2 Burner 1 √
B3 Control Panel 1 √
B4 Knob (Pre-Assembled) 2 √
B5 Hose and Regulator Assembly 1 √
B6 Lava Rock in Basket 1 √
B7 Cooking Grill 1 √
B8 Ignition Button (Pre-Assembled) 1 √
B9 Control Panel Heat Shield 1 √
B10 Main Electrode 1 √
B11 Hinge Bracket (Pre-Assembled) 2 √
B12 Body Heat Shield 1 √
B13 Body Support 2 √
B14 Grease Cup Holder 1 √
B15 Grease Cup 1 √
TROLLEY
C1 Side Shelf (with bracket)
C2 Side Shelf (without bracket) 1 √
C3 Side Shelf Bracket A 1 √
C4 Side Shelf Bracket B 1 √
C5 Side Burner Knob 1 √
C6 Side Burner Grid 1 √
C7 Side Burner Shelf 1 √
C8 Side Burner 1 √
C9 Side Burner Electrode 1 √
C10 Side Burner Valve / Hose Assembly 1 √
C11 Left Front Leg 1 √
C12 Left Rear Leg 1 √
C13 Right Front Leg 1 √
C14 Right Rear Leg 1 √
C15 Gas Bottle Holder 1 √
C16 Leg End Loop 1 √
C17 Wheel Spacer 2 √
C18 Wheel 2 √
C20 Axle 1 √
C21 Bottom Shelf 1 √
C22 Gas Bottle Strap 1 √
HARDWARE
D1 M6x15 Bolt 28 √
D2 M5x10 Bolt 4 √
D3 M4x10 Bolt 1 √
D4 ST4.0x10 Screw 7 √
D5 ST4.0x15 Screw 4 √
D6 ST4.8x15 Screw 2 √
D7 M8 Locknut 2 √
D8 M5 Nut 2 √
D9 Spacer 6 √
D10 Hose Tidy 1 √
C19 Wheel Hubcap 2 √
3
A2
B1
A1
B11
Parts Diagram:
Quantity varies according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see the corresponding ‘Hardware Reference Diagram’.
A3
C6
C8
C7
C5
B2
B12
B13
B10
B7
B6
B15
B14
C2
C3
C4
C12
C22
C15
C18 C20
C16
C13
C14
C21
C11
C17
B8
B4
B3
B9
C9
B5
C10
A4
C19
4
Hardware Reference Diagram:
Specifications subject to change without prior notice.
D1
D1
D2D4
D8
D3
D9 D5 D7D6
D10
5
C14
Assembly
IMPORTANT!
TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,
adjustable spanner or metric spanner set.
The assembly of this barbecue requires 2 people.
Whilst every care is taken in the manufacture of this product, care must be taken during assembly in
case sharp edges are present.
Please read the Important Information section carefully before assembly and use of your
barbecue.
2
Attach the Left Front Leg (C11) and Left Rear Leg (C12) to the Gas Bottle Holder (C15) using
ST4.0x10 Screws(D4x4pcs).
C16
Attach the Right Front Leg (C13) and Right Rear Leg (C14) to the Leg End Loop (C16). The
legs are a push fit onto the leg end loop. In case of difficulty, they may need tapping with a soft
faced mallet. Take care not to damage the parts.
1
C11
C12
C15
C13
C14
6
Attach the Bottom Shelf (C21) to the Gas Bottle Holder (C15) using ST4.8x15 Screws
(D6x2pcs). Take care not to over tighten these screws which will damage the plastic gas
bottle holder.
Attach the leg assembly to the bottom shelf assembly using M6x15 Bolts (D1x4pcs).
4
3
C21
C15
D6
D1
7
Insert the Axle (C20) through the clamping brackets underneath the Gas Bottle Holder (C15) and
tighten the clamping screws. Take care not to over tighten these screws which will damage the
plastic gas bottle holder.
Slide a Wheel Spacer (C17) over each end of the Axle (C20). Note: the spacers are packed in a
plastic bag with the main electrode, grease cup holder and grease cup.
Slide the Wheels (C18) over each end of the axle. Secure the wheels into place with the M8 Lock-
nuts (D7x2pcs). Place the Wheel Hubcaps (C19) onto the outside of the wheels.
Carefully turn the completed trolley over, right side up.
Attach the Body Support (B13) to the legs using M6x15 Bolts (D1x4pcs).
6
5
C15
C20 C17
D7
D1
B13
√
×
C18 C19
8
a. Unscrew the nut from the Heat Indicator(A4).
Place the heat indicator through the hole on the top of Hood(A1). Tighten the heat indicator
with the nut.
b. Attach the Hood Handle (A2) to the Hood (A1) using the M5x10 Bolts (D2x2pcs).
Carefully place the Barbecue Body (B1) onto the tops of the legs.
Attach the barbecue body to the trolley assembly using the M6x15 Bolts (D1x8pcs). Ensure the tabs
on the body fit over the legs as shown in the diagram and do not go down inside of the legs.
WARNING: DO NOT RELEASE THE BARBECUE BODY WHILE THE BARBECUE HAS NOT BEEN
PROPERLY SEATED. THIS MAY RESULT IN INJURY OR DAMAGE TO YOUR BARBECUE.
8
7
B1
A1
A4
A2
D2
D1
9
Feed the Grease Cup Holder (B14) through the hole in barbecue body.
Insert the Grease Cup (B15) into the grease cup holder.
10
9
Install a M6x15 Bolt (D1) and a Spacer (D9) into the upper fixing hole on each front leg.
Place the Control Panel (B3) assembly in position by aligning the spacers with the slot on
each side of control panel and fix it to the trolley assembly using M6x15 Bolts (D1x2pcs).
B14
B15
D1
D9
D1
1
3
2
B3
10
Insert the Main Electrode (B10) into the hole at the bottom of the barbecue body and
secure with the pre-assembled nut.
Feed the Burner (B2) into barbecue body. Ensure that the burner venturi tubes are over the
ends of the gas valves. They are a loose fit and not a gas tight seal. Secure the burner with
the ST4.0x10 Screws (D4x2pcs).
View from underneath the body
12
11
B2
B10
D4
√
×
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Parrilla de Outback
Outback
Outback Spectrum 2 Burner Manual de usuario
Outback
Outback GD4222S-S Manual de usuario
Outback
Outback THG2302P-3 Manual de usuario
Outback
Outback RC4341C Manual de usuario
Outback
Outback Excel 310 Manual de usuario
Outback
Outback Dual Fuel 2 Manual de usuario
Outback
Outback CS3200 Manual de usuario
Outback
Outback THG3302PC Manual de usuario
Outback
Outback Meteor Select 3 Burner Gas BBQ MH3330 Manual de usuario
Outback
Outback Cook Dome 571 Manual de usuario
Outback
Outback Mayfair Manual de usuario
Outback
Outback Sapphire THG3216AW Manual de usuario
Outback
Outback Trooper Plus Manual de usuario
Outback
Outback Omega 100 Manual de usuario
Outback
Outback Jupiter 4 Manual de usuario
Outback
Outback OUTBACK TROOPER 359 Assembly and Manual de usuario
Outback
Outback Cuisine Manual de usuario
Outback
Outback CK578T Manual de usuario
Outback
Outback Spectrum THG2302PA Manual de usuario
Outback
Outback Gourmet 4 Manual de usuario
