Onicon D-100 Manual de usuario

D-100 FLOW DISPLAY

BACnet Network Interface Installation Guide

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699

www.onicon.com • [email protected] 03-18

0635-11 / 18341

BACnet

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 2

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 3

TABLE OF CONTENTS

1.0 INTRODUCTION ..................................................................................................5

1.1 PURPOSE OF THIS GUIDE .......................................................................5

1.2 TYPICAL D-100 FLOW DISPLAY .............................................................5

1.3 SPECIFICATIONS ......................................................................................5

1.4 NETWORK SIGNAL CONNECTIONS.......................................................6

1.4.1 BACnet MS/TP................................................................................6

1.4.2 BACnet/IP........................................................................................7

1.4.3 Optional Network Interface with

Isolated Digital Pulse Input (Di3) ...................................................8

1.5 BACnet MS/TP BAUD RATE, BIASING AND TERMINATION .............11

1.5.1 Baud Rate ......................................................................................11

1.5.2 Biasing and Termination...............................................................12

1.6 NETWORK ADDRESSING.......................................................................12

1.6.1 Changing the MAC (Device) Address...........................................12

1.6.2 Changing the IP Address ..............................................................14

1.6.3 Changing the Gateway Address....................................................17

2.0 BACnet PICS AND OBJECTS .............................................................................20

2.1 PIC STATEMENT .....................................................................................20

2.2 BAC OBJECTS..........................................................................................22

2.3 ADDITIONAL BACnet OBJECT INFORMATION ...................................23

2.4 ANALOG INPUT(S).................................................................................24

2.5 ANALOG VALUE(S) ................................................................................25

2.6 BINARY VALUES(S)................................................................................26

3.0 NETWORK TROUBLESHOOTING TIPS ...........................................................27

3.1 TROUBLESHOOTING .............................................................................27

APPENDIX

A-1 D-100 PROCESSOR BOARD

A-2 D-100 BACnet MS/TP BOARD

A-3 D-100 BACnet IP BOARD

A-4 D-100 BACnet/IP Auxiliary Input Board (Di3)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 4

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 5

D-100

SCROLL RESET PROGRAM

ONICON

3864

Steam Building

Domestic Water Supply

Flow rate and total data to

Data Acquisition System or

Building Control System

120VAC or 24VAC

Input Voltage

1.3 SPECIFICATIONS

BACnet NETWORK INTERFACE

MS/TP RS485

Transceiver: 2-wire, half-duplex

MAC address (device address) range: 1 - 254 (Default: 017)

Device Instance: 0-4,194,303 (Default: 57017)

Baud rate: 9600, 19200, 38400, 76800 or Auto-Baud (Default: Auto)

Termination: 120 ohms or none (Default: none)

Biasing: None

Flow control: None

UDP/IP

Transceiver: Base 10T, 10Mbps, Rj45 connection

Device Instance: 0 - 4,194,303 (Default: 57017)

Default IP address: 192.168.1.24 (Subnet Mask 255.255.255.0) (Port 47808)

Flow control: None

SECTION 1: INTRODUCTION

1.1 PURPOSE OF THIS GUIDE

The purpose of this guide is to provide installation and commissioning procedures and basic

operating and servicing instructions for the ONICON D-100 BACnet serial interface.

1.2 TYPICAL D-100 FLOW DISPLAY

The D-100 is a totalizing display module that provides a local indication of liquid, gas or

steam ow rate and total data. It can also be provided with an optional BACnet MS/TP or

BACnet/IP serial interface to communicate data to the building control network.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 6

1.4 NETWORK SIGNAL CONNECTIONS

1.4.1 BACnet MS/TP

BACnet MS/TP, 2-wire (half-duplex) serial output connections are connected to terminal

T1 as shown. Do not exceed 4.4 in-lb (0.5 Nm) of torque when tightening.

Terminal

Do not connect

shields to this

terminal.

CAUTION

Only qualied service personnel should make connections between the D-100 Flow Display

and the user’s external equipment. ONICON assumes no responsibility for damage caused to

the external equipment as a result of an improper installation.

CAUTION

Incoming and outgoing RS485 cable shield wires should be connected together, but must not be

connected to the display.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 7

1.4.2 BACnet/IP

BACnet/IP, Base 10T output connections are made as shown. Requires Base 10T cable and

RJ45 connector.

CAUTION

Only qualied service personnel should make connections between the D-100 Flow Display and the

user’s external equipment. ONICON assumes no responsibility for damage caused to the external

equipment as a result of an improper installation.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 8

1.4.3 Optional Network Interface With Isolated Digital Pulse Input (Di3)

The D-100-BACnet Display can be provided with an digital input pulse for totalizing pulse

outputs from external devices such as water or gas meters. Pulses are accumulated in an

internal register, and the totalized value is available on the network. This register can be

zeroed via the network. The maximum register is 9,999,999. The register will rollover to

zero when this value is exceeded.

If the digital pulse input option was ordered at the same time the display was ordered,

it will arrive fully congured and ready to use. If it was ordered after the display was

delivered and is being installed as a eld upgrade, it may be necessary to congure the

pulse input. The information required to congure the input is provided below and on the

following pages:

The input pulse must meet the following criteria:

1. Frequency input range, 50 Hz maximum

2. 10 millisecond minimum pulse duration

Input Pulse Denition:

In order to congure the communications card for an digital input pulse, you must

rst determine which type of pulse your meter produces. The allowable types of input

pulses are described on the following pages. Based on the type of pulse, set the selector

switch (S1) on the communications circuit board (Fig. 1) to the correct setting.

Fig. 1

120 ohm Jumper Selectable

Termination Resistor

Pulse Type Selector Switch (S1)

Input Impedance Jumper (J1)

Digital Pulse Input (Di3) Connector

RS485 Connector (T1)

NOTE: BACnet MS/TP shown above. See appendix A-4 for BACnet/IP auxiliary input board.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 9

Powered Pulse:

This type of output refers to a pulse which has an associated voltage with it (see Fig. 2).

Set the selector switch, S1 to Pwrd Pulse. The allowable voltage range is 5-24 VDC. The

input impedance is set at the factory to be 11 KOHM via the impedance selector jumper

(J1, see Fig. 1). A lower impedance, 3 KOHM can be selected if required by the instrument

providing the pulse output. Consult the instrument manufacturer or ONICON if you are

uncertain as to the proper jumper selection.

Fig. 2

Open Collector (Sourcing):

This type of output refers to an open Collector Switch congured for a sourcing function

(see Fig. 3). Set the selector switch, S1 to SRC. The switch must be rated for at least 20 mA

at 20 VDC.

Fig. 3

ONICON BTU Meter

DI3 In (+)

J1 = HI (11 Kohm)

DI3 In (-)

ONICON BTU Meter

DI3 In (+)

DI3 In (-)

Pulse Switch and Jumper Location

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100 Display Module BACnet Installation and Operation Guide 03/18 - 0635-11 / 18341 Page 10

Open Collector Sinking or Dry Contact:

This type of output refers to an open collector switch congured in a current sinking

arrangement or a dry contact switch (see Fig. 4 and 5). Set the selector switch, S1 to Sink.

In either case, the switch must be rated for at least 20 mA at 20 VDC.

Fig. 4

Fig. 5

DI3 In (+)

DI3 In (-)

DI3 In (+)

DI3 In (-)

ONICON BTU Meter

Otros manuales para D-100

Tabla de contenidos

Otros manuales de Instrumento de medición de Onicon

Onicon

Onicon Fox Thermal FT1 Manual de usuario

Onicon

Onicon D-1401 Instrucciones de funcionamiento

Onicon

Onicon F-4300 Instrucciones de funcionamiento originales

Onicon

Onicon F-1000 SERIES Manual de usuario

Onicon

Onicon System-10 BTU Meter Instrucciones de funcionamiento

Onicon

Onicon FP-4400 Instrucciones de funcionamiento originales

Onicon

Onicon System-10 BTU Meter Manual de usuario

Onicon

Onicon F-3200 Series Instrucciones de funcionamiento originales

Onicon

Onicon D-100 Manual de usuario

Onicon

Onicon FT-3400 Instrucciones de funcionamiento

Onicon

Onicon SYSTEM-30 Instrucciones de funcionamiento

Onicon

Onicon F-1000 SERIES Manual de usuario

Onicon

Onicon F-5000 Instrucciones de funcionamiento

Onicon

Onicon D-100 Manual de usuario

Onicon

Onicon FT-4600 Instrucciones de funcionamiento

Onicon

Onicon F-5200 Instrucciones de funcionamiento

Onicon

Onicon SeaMetrics AG90 Manual de usuario

Onicon

Onicon SYSTEM-20 Instrucciones de funcionamiento

Onicon

Onicon SYSTEM-30 Instrucciones de funcionamiento

Onicon

Onicon F-2500 series Instrucciones de funcionamiento

Onicon

Onicon F-4300 Instrucciones de funcionamiento originales

Onicon

Onicon F-1000 SERIES Instrucciones de funcionamiento

Onicon

Onicon Fox Thermal FT2A Manual de usuario

Onicon

Onicon F-4300 Instrucciones de funcionamiento originales

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario